NANLITE D672B LED Panel Light User Manual

USER MANUAL
D672B LED Panel Light
Guangdong NanGuang Photo&Video Systems Co., Ltd

D672B LED Panel Light

Product Show

Technical Data

LED Power: 148W
Power Input: AC 110V-220V
Color temperature: 3200K-5600K
CRI(Ra): 95

Product Details

Detailed Description

1. Barndoor: For adjusting the illumination range of fixture.
2.  2.4G Antenna: Use to receive 2.4G remote control signals.
3. Display Screen: For showing the related data.
4. Address Code Button: For adjusting the address code for the fixture’s wireless control.
5. DMX OUT: DMX signal output interface.
6. DMX IN: DMX signal intput interface.
7.  Dimmer Knob: For adjusting the brightness of the light.
8. Yoke: For connecting the fixture to the light stand and adjusting the direction of the light.
9.  Angle Fixing Knob: For adjusting and securing the position of the light on in a given position or direction.
10. Fuse Holder: For placing the fuse.
11. Power Switch: For powering the fixture on or off.
12. CCT Knob: For adjusting the color temperature of the light.
13. AC Power Socket: AC power input interface.
14. Bracket fixing knob: For connecting the fixture and adjusting the horizontal direction of fixture on a stand or other mounting solutions.

Usage

1. Connection with the controller
   ·The connection cable between the light fixture and control unit, light fixture and light fixture should use three core shielded cable and make sure it’s diameter is not less than 0.3mm2. XLR plug/socket and the wires should be connected as the pictures as above.
   ·Pin1, Pin2, Pin3 is for connecting DMX signals, Pin4, Pin5 is connectionless.
   ▲NOTE: When connecting with socket, make sure the internal pins are not in contact with the inner case. The fixture can match the DMX(1990) control signal.
   ·Plug of five-core and three-core XLR plug/socket conversion.
   The fixture comes with the five-core XLR plug. If you use the three-core XLR plug, kindly follow below instruction.

2. 3-Pin DMX circuit
   In DMX mode, make sure the last light is the only light with cable connected to DMX output. There is a resistance about 120(OHM) between the second pin and third pin of this plug(as below photo). Make sure this plug is installed into the output of the last fixture which can avoid noise and reflection phenomenon caused by DMX signal in the transmitting process.

3. DMX channel control
   When the light is bi-color, select the address code to 001, it correspond to the CH1, CH2 of the console. After confirming the address code, the address code will be the last setting address when turning on the light.

4. 2.4G Wireless Remote Control
   The D672B is designed to work with a 2.4G remote controller or Nanguang/Nanlite WIFI-APP via WIFI transfer device to control the light remotely.
   NOTE: 2.4G remote controller or WIFI transfer device sold separately. (See separate instructions for remote controller or WIFI transfer device.)

Operating Instructions

1. Fix the light on a light stand, unfold the barn door, adjust the angle and tightening knob and bracket fixing knob of the fixture to the the desired direction and angle.

2. Please make sure that the power switch on the fixture is in the “off” position, then connect the power cable before turning on the power.

3. When setting the brightness, rotate the dimmer knob in a clockwise rotation to increase brightness and counterclockwise to decrease brightness. The display will show the data of the brightness range from L.000 to L.100.(As figure 1)

4.  When setting the color temperature, rotate the CCT knob in a clockwise rotation to increase the color temperature and counterclockwise to decrease color temperature. The range of the color temperature is 3200K-5600K.(As figure 2)

5. When setting the address code, press the “+” to increase the address code number and press “-” to decrease the address code number. The display will shows the address code number of the fixture in the range from A.001 to A.512.
   These two buttons support click or long press.(As figure below)

6. When finished using the fixture, power off the fixture.

Safety Precautions

1. Please open the package to check if it is damaged due to transportation after receiving the light. In case of damaged cased by transportation, please do not use the light and contact the dealer or manufacturer as soon as possible.
2. Do not use a power cord with damaged insulation. Do not unplug hard or drag the power cord directly.
3. Make sure that the power supply voltage used matches the voltage specified by the light before installation.
4. When not using or cleaning the light, please turn it off.
5. Keep the light safely stored and away from children.

Notice

1. Please make sure that the power voltage and frequency is within the specified range when connecting the power.

2. When the light is on, don’t look direct at the emitter.

3. Don’t place objects on the light emitter or allow liquid to flow inside the fixture or the emitter.

4. Don’t place fixture near flammable substances like alcohol or gasoline.

5. When cleaning the fixture, please wipe off debris or dirt using cloth and only dampen with water or light cleanser.

6. The fixture should be placed in a well ventilated place and do not use in humid, dusty or overheated environment.
   Please also check if the ventilation hole is not obstructed.

7. Do not repair the fixture yourself. Repair professionals, please adhere the user manual while troubleshooting.

8. For optimal cooling of the fixture, the vents should not be covered whening using, or will damage the equipment.
   When using the fixture for a long time, the temperature of the fixture is high, please pay attention to anti-scalding.

What’s in the box ? Please kindly check

Genaral Fault Detection and Diagnosis

fixture is in “off” position.
2. Please check if there are any loose connection between     the adapter, power cord or port on fixture.
The fixture can light normally, but controllers are not function.| 1. Please check whether the DMX original address setting of     the fixture is correct or not.
2. Please check if the XLR signal cable is connected correctly     or is damaged.
LCD display is on but can not opreate light.| The internal CPU is damaged, please contact the supplier or return to the manufacture.

If the failure is not solved after the above troubleshooting procedures, please contact the dealer or manufacturer for repair.
This manual and all stats within it were produced under controlled conditions, and are accurate at time of print. Any future changes to design/technical data can be found at www.nanlite.com.

Version:V2 2020-01-09
**** +86-754-85751187
service@nanlite.com
+86-754-85300887
Zhanglin,324,Dongli Chenghai Shantou Guangdong China
www.nanlite.com

References

• NANLITE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>