NANLITE WC-USBC-C1 Wire Controller User Manual
- June 6, 2024
- NANLITE
Table of Contents
WC-USBC-C1
USER MANUAL
WC-USBC-C1 Wire Controller
Product Diagram
WC-USBC-C1 wire controller is compatible with PavoBulb 10C and PavoTube T8-7X.
Usage
-
Connect the wired controller to the fixture, then toggle the power switch to turn on the wired controller, the “NANLITE” logo will be displayed on startup.
-
When the wired controller is connected to the fixture, the wired controller will first read the information of the fixture, including the address and fixture model.
①When the wired controller is not connected to the fixture, the display will show “Disconnected” (As shown in figure 1);
②When the wired controller is connected to the fixture, the screen will display the corresponding lighting mode interface or menu of the fixture. (As shown in figure 2)
Note: (1) When the wire controller is connected to
PavoBulb 10C, the lighting mode options include CCT, HSI, and EFFECT.
(1) When the wire controller is connected to PavoTubeT8-7X, the lighting mode options include CCT, HSI, EFFECT, PIXEL FX. -
MODE button: For switching lighting modes and menu.
-
SWITCH button: For switching corresponding options under different light modes, or to switch the channel, language, DMX mode, DMX pixel (only for PavoTube T8-7X), wireless protocol (only for PavoBulb 10C), Bluetooth reset, firmware update, and version under the menu options.
-
+ – button: For adjusting the value of the corresponding options under the lighting mode. (As shown in figure 3)
-
Press the MODE button to enter the menu.
Press the SWITCH button to CH.
Press + – button to adjust the value of the address code.
Press the SWITCH button to LANGUAGE.
Press + – button to select Chinese or English.
Press the SWITCH button to DMX MODE.
Press + – button to select the desired DMX mode.
④DMX PIXEL setting (Note: Only controllable with PavoTube T8-7X.)
Press the SWITCH button to DMX PIXEL.
Press + – button to adjust the number of DMX pixels.
⑤Wireless protocol setting (Note: Only controllable with PavoBulb 10C.)
Press the SWITCH button to WIRELESS PROTOCOL.
Press + – button to select V1.0 or V2.0.
Press the SWITCH button to BT.
Press + – button to enter the interface of Bluetooth
reset.
Press the SWITCH button to RESET.
Press the MODE button to confirm reset and it will return to the menu interface after resetting the Bluetooth.
⑦Firmware update
-
Firmware update for the wired controller
Switch off the wired controller, and then insert the USB flash drive with the new firmware for the wired controller, the screen will show as below:
Press the SWITCH button to UPDATE.
Press the MODE button to confirm the update, it will
prompt “FIRMWARE UPDATED” after the firmware is upgraded. -
Firmware update for fixtures via wire controller
Switch on the controller and connect it to the fixture to be upgraded, insert the USB flash drive with the new firmware of the fixture, turn on the fixture, then press the MODE button to switch to the menu interface.
In the menu, press the SWITCH button to the firmware update.
Press + – button to enter the firmware update interface.
Press the SWITCH button to UPDATE.
Press the MODE button to confirm the update, it will
prompt “FIRMWARE UPDATED” after the firmware is upgraded.
Press the SWITCH button to VERSION.
7. USB Type C port: For firmware updates, or connect with the USB cable, and
then connect to the USB adapter with an output of 5V/2A or above to charge the
wire controller.
8. The wired controller has a built-in lithium battery and can power the
PavoBulb 10C and PavoTube T8-7X directly.
9. Please switch off the controller when not in use.
Notice
- The wired controller is only compatible with PavoBulb 10C and PavoTube T8-7X.
- When the battery level is low, it is recommended to reduce the brightness to less than 50% for charging or turn it off and fully charge before using it again.
- When the wired controller is not connected to the fixture and is powered off, connect the power supply, now the display will show ” ” and the icon is scrolling; when the battery is fully charged, the display shows ” “.
This manual has been compiled according to the rigorous testing of our company’s products. Product designs are subject to change without prior notice. You can download the latest version of the manual for this particular product from www.nanlite.com.
Version: V2 2022-02-16
+86-754-85751187
service@nanlite.com
+86-754-85300887
Zhanglin,324,Dongli Chenghai Shantou Guangdong China
www.nanlite.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>