Ashly FX500.2 500W 2 RU Class-D Amplifier User Manual
- June 12, 2024
- ASHLY
Table of Contents
Ashly FX500.2 500W 2 RU Class-D Amplifier
Description
The Ashly FX500.2 belongs to the FX Series by Ashly and is a 2U Compact Class D Power Amplifier delivering 1000W of power. The FX Series is the culmination of successful compact Class D design from the FA Series and Ashly’s years of user-friendly software provision. Featuring a newly integrated DSP engine & software UI, FX raises the bar for amplification. FX offers networkability through Ethernet for wired LAN or its built-in WiFi hotspot, eliminating the need for a network router.
This integration of functions saves both space and time, negating the necessity for additional equipment such as standalone DSP or speaker system processors—all contained within a single box. With 6 models available, ranging from 2 x 60W in a ½ RU to 4 x 500W in 2 RU, there’s an FX suitable for a wide array of projects. Each model comes equipped with a variety of IO options, including Digital SPDIF In & Out, and programmable integration ports for remote Volume control, GP triggers, and more.
Specifications
- Channels: 2 x Lo-Z / 1x Hi-Z
- Output Power @ 4Ω/8Ω: 2x500W (SE) at 2Ω, 2x500W (SE)/1x1000W (BTL) at 4Ω, 2x400W (SE)/1x1000W (BTL) at 8Ω
- Output Power @ 25V: To Be Determined
- Output Power @ 70V/100V: 1x1000W (BTL)
- Powershare – Across All Channels (up to): 1x750W (SE)
- Total System Power: 1000W
- DSP: 4 Input x 2 Outputs with Input, Zone, Output & Speaker Processing, plus General Settings
- Networking: Browser-based UI Software with Ethernet & WiFi Connectivity
- Power Consumption: 550W
- Dimensions: 89×482.5x320mm (19×3.5×12.6 inch)
- Weight: 7.5 kg (16.5 lbs)
- Output Circuitry: UMAC Class D – Full bandwidth PWM Modulator with Ultra-low Distortion
- Output Voltage: 85 Vp / 170 Vpp (unloaded) // Bridged 170 Vp / 340 Vpp (unloaded)
- Signal to Noise-Ratio: >108 dB (A-Weighted, 20 Hz – 20 kHz, 8 Ω load)
- THD+N (typical): <0.05% (20 Hz – 20 kHz, 8 Ω load, 3 dB below rated power)
- Frequency Response: 20Hz-20kHz (+/- 0.5dB, 8 Ω load, 3 dB below rated power)
- Protection Circuits: Short Circuit, DC, Undervoltage, Temperature, and Overload Protection
- Power Supply: UREC Universal Mains switch mode power supply with Power Factor Correct (PFC) and Standby Converter
- Operating Temperature: 0-40°C
- Operating Voltage/Frequency: Universal Mains, 100V – 240V, 50Hz – 60Hz
- Standby Consumption: To Be Determined
- Accessories: Rack Ears (Included)
- Power Ratings: 1% THD @ 120 Vac and 230 Vac
Specifications of Multiple Series
This robust Class D power amplifier is particularly well-suited for applications in auditoriums, catering, and conference rooms, among others.
What’s in the Box
Upon unboxing the Ashly FX500.2 500W 2 RU Class-D Amplifier, you’ll find:
- Ashly FX500.2 Amplifier Unit
- Removable Euroblock connectors for balanced Mic/Line inputs
- Unbalanced RCA input connectors
- Rack Ears for installation in standard equipment racks
- User Manual and Quick Start Guide
- Power Cord
Various Connectivity Ports
Key Features
- High power density: 500W x 2Ch in 2 RU chassis
- Selectable Low (2*/4/8 Ohm) or Hi Impedance (70/100V) operation via software
- Balanced Mic/Line inputs on removable Euroblock connectors, along with unbalanced RCA inputs
- 2-channel SPDIF Digital IO
- Front panel LEDs for amp, Input, output & network status
- Networkable via Ethernet or built-in WiFi
- Built-in advanced DSP on all inputs & outputs, offering Sensitivity, Routing, Gain, PEQ, Compressor, Limiter, FIR Filters, X-Over, Polarity & Delay
- Browser-based UI accessible through PC or mobile devices—no software installation needed
- All models are equipped with 4 Input channels x 2 or 4 Output channels
- Auto/Manual Power Saver Mode (sleep/standby), adjustable via Software
- Customizable Speaker Presets can be created, saved & loaded for each output channel
- Addressable GPIO, Standby/Mute & VC remote ports; VC assignable per channel via software
- Highly efficient Class D technology with a lightweight build
How to Use
Using the Ashly FX500.2 500W 2 RU Class-D Amplifier involves several steps to ensure optimal performance and functionality.
Here’s a basic guide on how to use the amplifier:
-
Physical Setup:
- Rack Installation: Mount the amplifier in a standard 2 RU equipment rack using the included rack ears.
- Connections: Connect your audio sources (microphones, line-level devices, etc.) to the balanced Mic/Line inputs using Euroblock connectors or unbalanced RCA inputs as needed. Connect your speakers to the amplifier’s output terminals.
- Power: Plug in the power cord and ensure the amplifier is connected to a suitable power source.
-
Power On and Initial Check:
- Power On: Turn on the amplifier using the power switch.
- LED Status Lights: Check the front panel status LEDs for amp, input, output, and network status. This will give you an initial indication of the amplifier’s functioning.
-
Remote Control and Configuration:
- Network Setup: If you wish to control the amplifier remotely, connect it to your network either via Ethernet or the built-in WiFi hotspot. Consult the user manual for instructions on connecting to the network.
- Browser-Based UI: Access the amplifier’s settings and controls using the browser-based UI software. Open a web browser on your PC or mobile device and enter the amplifier’s IP address or hostname. This will give you access to various parameters and configurations.
-
Audio Configuration:
- Input Routing: Use the DSP settings to route your input sources to the desired output channels. You can adjust sensitivity, gain, EQ, compression, and other audio processing settings.
- Output Configuration: Configure your output channels based on your speaker setup. You can apply EQ, crossover settings, and other parameters to optimize the sound.
-
Speaker Presets:
- Customization: Create and save customized speaker presets for each output channel. This allows you to quickly recall specific settings for different setups.
-
Remote Control and Monitoring:
- Remote Control: Use the browser-based UI to adjust settings, change presets, and monitor the amplifier remotely.
-
Energy Efficiency and Standby Mode:
- Power Saver Mode: Configure the amplifier’s power saver mode to automatically go into standby or sleep mode when not in use. This helps save energy.
-
Monitoring and Maintenance:
- Status Checks: Regularly monitor the front panel LEDs and browser-based UI for any status updates or issues.
- Firmware Updates: Check for firmware updates from Ashly’s official website and follow the instructions to keep your amplifier up to date.
-
Shutdown:
- Power Off: When you’re done using the amplifier, turn it off using the power switch.
-
Safety Precautions:
- Proper Ventilation: Ensure the amplifier has adequate ventilation to prevent overheating.
- Load Matching: Use appropriate speakers and match impedance settings to avoid damaging the amplifier or speakers.
User Support
- SUPPORT HOURS
- Monday – Friday 8:30 AM – 6:00 PM EST Closed on US Holidays
TECH SUPPORT GURUS
- Jim Schwenzer – Email Jim
- 585-872-0010 x124
- Mike Bow – Email Mike
- 585-872-0010 x140
CALLING TECH SUPPORT
North America & The Caribbean
- +1-800-828-6308 (toll-free)
- +1-585-872-0739 (fax)
- Email Tech Support
All International Countries
- +1-585-872-0010
FAQ’s
What is the power output of the Ashly FX500.2 amplifier?
The Ashly FX500.2 amplifier delivers 500W of power per channel, making it suitable for a wide range of audio applications.
Is the FX500.2 amplifier compact?
Yes, despite its high power output, the FX500.2 is designed with a compact 2 RU form factor, saving space in equipment racks.
Does the amplifier have built-in DSP?
Yes, the FX500.2 features an advanced DSP engine that provides functions like Sensitivity, Routing, PEQ, Compressor, Limiter, FIR Filters, X-Over, Polarity, and Delay.
Can I control the amplifier remotely?
Absolutely, the FX500.2 offers remote control capabilities through browser- based UI software, accessible via PC or mobile devices.
Is network connectivity available?
Yes, the amplifier is networkable through Ethernet or its built-in WiFi hotspot, eliminating the need for an external network router.
How many input and output channels does the amplifier have?
The FX500.2 has 4 input channels and 2 output channels, allowing for flexible audio routing and configuration.
Can I save and load customized speaker presets?
Yes, you can create, save, and load customized speaker presets for each output channel, ensuring optimal sound for different setups.
Does the amplifier offer both high and low impedance operation?
Yes, you can select between Low (2*/4/8 Ohm) or Hi Impedance (70/100V) operation via software settings.
Is the amplifier energy-efficient?
Yes, the FX500.2 features Auto/Manual Power Saver Mode (sleep/standby), which can be adjusted in software to optimize power consumption.
What kind of protection circuits does the amplifier have?
The amplifier is equipped with protection circuits for Short Circuits, DC, Undervoltage, Temperature, and Overload, ensuring the safety of both the amplifier and connected speakers.
What are the dimensions of the FX500.2 amplifier?
The dimensions are 89x482.5x320mm (19x3.5x12.6 inches), making it suitable for rack installations.
What applications is the FX500.2 amplifier ideal for?
The FX500.2 is ideal for various applications including auditoriums, catering, conference rooms, and more, thanks to its high power output and versatile features.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>