Fellowes Saturn 3i 95 Thermal Laminator Machine Quick Start Guide

Fellowes Saturn 3i 95 Thermal Laminator Machine

LAMINATOR CONTROLS

• A. On / off switch
• B. Laminator feed sensor
• C. Pouch selection buttons ( , 3 Mil, 4 Mil, 5 Mil)
• D. Release lever ( )
• E. Pouch / document entry slot
• F. Entry support shelf
• G. Pouch / document exit

CAPABILITIES

• Entry width: 125 = 12.5” / 318mm; 95 = 9.5” / 240mm
• Pouch thickness (min): 3 Mil (per side)
• Pouch thickness (max): 5 Mil (per side)
• Warm-up time (estimate): 1 minute
• Cool down time: 60-90 minutes
• Lamination speed (+/- 5%): approx. 12”/min (fixed speed)
• Number of rollers: 2
• Ready indication: Light & beep
• Release lever: Yes
• Cold lamination: Yes

Technical Data

• Voltage / Frequency / Current(Amps): 125 = 120V AC, 60Hz, 6.1A; 95 = 120V AC, 60Hz, 6.1A
• Wattage: 125 = 750 Watts; 95 = 750 Watts
• Dimensions (HxWxD): 125 = 4-1/8” x 20-15/16” x 5-3/4”; 95 = 4-1/8” x 17-3/16” x 5-1/2”
• Net weight: 125 = 5 lb; 95 = 4 lb
• Max document thickness (laminating capacity): .02” / 0.5 mm

IMPORTANT SAFETY INSTRUCTIONS

KEEP FOR FUTURE USE

• The machine is for indoor use only. Plug the machine into an easily accessible socket.
• To prevent electrical shock – do not use the appliance close to water, do not spill water on to the appliance, power cord or wall socket.
• DO ensure the machine is on a stable surface.
• DO test laminate scrap sheets and set the machine before final laminations.
• DO remove staples and other metal articles prior to laminating.
• DO keep the machine away from heat and water sources.
• DO turn off the machine after each use.
• DO unplug the machine when not in use for an extended period.
• DO use pouches designed for use at the appropriate settings.
• DO keep away from pets, while in use.
• DO ensure self-adhesive pouches are only used with the cold setting
• DO NOT leave the power cord in contact with hot surfaces.
• DO NOT leave power cords hanging from cupboards or shelves.
• DO NOT use the appliance if the power cord is damaged.
• DO NOT attempt to open or otherwise repair the machine.
• DO NOT exceed the machine’s quoted performance.
• DO NOT allow children to use this machine without adult supervision.
• DO NOT laminate sharp or metal objects (eg: staples, paper clips).
• DO NOT laminate heat-sensitive documents (eg: tickets, ultrasounds, etc) on hot settings.
• DO NOT laminate with self-adhesive pouches on hot settings.
• DO NOT laminate an empty pouch.

FEATURES & TIPS

Lamination Feed Sensor
When the machine senses a pouch has been mis-fed or has not gone completely through the machine in normal operating time the Lamination Feed Sensor LED will blink. Use the release lever located at the rear of the machine to remove the laminate.

Auto Shut Off
If the machine is not active for 30 minutes, the Sleep Mode function will place the machine into standby mode. All LEDs will be dimly blinking. To operate the machine, press any button or cycle the power switch.

‘Release’ function
To remove or re-align a pouch during lamination, activate the release lever located at the rear of the machine. The pouch can only be removed from the entry slot when the lever is activated.

• For best results, use Fellowes® brand pouches: 3 Mil, 4 Mil, 5 Mil, and 5 Mil Cold Pouches.
• For self-adhesive (cold pouches) only use the cold setting.
• This machine does not need a carrier to laminate. It is a carrier-free mechanism.
• Always put the item to be laminated into the appropriately sized pouch.
• Always test laminate with a similar size and thickness before the final process.
• Prepare pouch and item for lamination. Place item within the pouch centered and touching the leading sealed edge. Ensure the pouch is not too large for the item.
• If required, trim excess material from around the item after lamination and cooling.
• When working with different pouch thicknesses’ (temperature settings) it is recommended to first start with the thinnest pouches.

SETTING UP THE LAMINATOR

1. Ensure the machine is on a stable surface.

2. Check there is enough clear space (min 20”) behind the machine to allow items to pass through freely.

3. Plug the machine into an easily accessible main socket.
   HOW TO LAMINATE
   

4. Switch the power on (located at the rear of the machine).

5. The control panel buttons will flash once as part of a check light system to ensure proper function.

6. The machine defaults to the 3mil hot setting. For 4mil, 5mil or cold laminating press the corresponding pouch selection buttons.

7. When the machine is ready, a beep will sound and the temperature setting button will stop flashing and remain on.

8. Place the document into the open pouch. Ensure the document is centered against the sealed edge. Use the appropriate pouch size for the document.

9. Ensure the pouch enters the machine-sealed edge first. Keep the pouch straight and central within the slot, not at an angle. Use the entry markings as a guide.

10. Upon exit, the laminated pouch may be hot and soft. For the best quality and to prevent jamming remove the pouch immediately. Place the pouch onto a flat surface to cool. Take care when handling a hot pouch. Always remove the laminate pouch before starting the next laminate.

11. To release a pouch during lamination activate the release lever located at the rear of the machine. Gently pull the pouch out of the machine.

NEED HELP?

Let our experts help you with a solution.
Customer Service... www.fellowes.com
Always call Fellowes before contacting your place of purchase, see the rear cover for contact details.

TROUBLESHOOTING

machine at the rear next to plug inlet and at the wall socket
Lamination Feed Sensor LED is blinking| Laminate was misfed| Hold down the release lever and remove the item by hand
All LEDs are dimly blinking| Laminator has gone into Auto Shut Off mode| Press any button or cycle the power switch to re-start the machine

The pouch does not completely seal the item

| The item may be too thick to laminate| Check pass through-thickness is correctly selected and pass through again
Temperature setting may be incorrect| Check pouch thickness is correctly selected and pass through again
The pouch has waves or bubbles| Temperature setting may be incorrect| Check pouch thickness is correctly selected and pass through again
The pouch is lost in the machine| Pouch is jammed| ****

Operate the release lever and pull out the item by hand

Jamming

| The pouch was used ‘open end’ first
The pouch was not centered on the entry
The pouch was not straight upon entry
An empty pouch was used
The pouch is damaged after lamination| Damaged rollers or adhesive on rollers| Pass cleaning sheets through the machine to test and clean rollers

STORAGE & CLEANING

• Switch off the machine at the wall.
• Allow the machine to cool.
• The outside of the machine can be cleaned with a damp cloth.
• Do not use solvents or flammable materials to polish the machine.
• Cleaning sheets can be used with the machine.
• When the machine is warm – run the sheets through the machine to clean any residue off the rollers.
• For optimum performance, it is recommended that cleaning sheets are used with the machine regularly. (Cleaning sheet order codes #5320603)

FCC CLASS B NOTICE

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CANADA CLASS B NOTICE – AVIS CANADA, CLASSE B
This Class B digital apparatus complies with Canadian ICES-003.

MODIFICATIONS
Any modifications made to this device that are not approved by Fellowes may void the authority granted to the user by the FCC and/or by Industry Canada to operate this equipment. 

Help Line

• Canada: + 1-800-665-4339
• México: +001-800-514-9057
• United States: + 1-800-955-0959

FAQ’s

What is the Fellowes Saturn 3i 95 Thermal Laminator Machine?

The Fellowes Saturn 3i 95 Thermal Laminator Machine is a device designed for laminating documents, photos, and other items using heat-activated laminating pouches. It provides a protective layer to preserve and enhance the appearance of your documents.

What is the maximum document size that the Saturn 3i 95 can laminate?

The Fellowes Saturn 3i 95 Thermal Laminator Machine can laminate items up to 9.5 inches wide, making it suitable for a variety of standard paper sizes, photos, and more.

How does thermal laminating work with this machine?

Thermal laminating involves inserting a document into a laminating pouch and passing it through the machine. The machine uses heat to activate the adhesive on the pouch, bonding it to the document and providing a protective layer.

What types of documents can I laminate using the Saturn 3i 95?

You can laminate a wide range of documents, including photographs, certificates, important papers, ID cards, educational materials, and more.

Does the machine come with adjustable temperature settings?

Yes, the Fellowes Saturn 3i 95 Laminator typically features adjustable temperature settings, allowing you to select the appropriate temperature for different laminating pouch thicknesses and materials.

What pouch thicknesses are compatible with the Saturn 3i 95?

The Fellowes Saturn 3i 95 Laminator is compatible with laminating pouches of various thicknesses, including 3 mil and 5 mil pouches. This versatility enables you to choose the level of protection and rigidity you need for your documents.

How long does the laminator take to warm up?

The warm-up time of the Fellowes Saturn 3i 95 Laminator varies, but it typically heats up within a few minutes, allowing you to start laminating quickly.

Is the laminator suitable for both home and office use?

Yes, the Fellowes Saturn 3i 95 Thermal Laminator Machine is designed for both home and small office use, offering a convenient way to protect and enhance your documents.

Can I use the laminator for back-to-back laminating without waiting?

Some laminators, including the Fellowes Saturn 3i 95, may require a cooldown period after laminating a few items back-to-back. It's advisable to follow the manufacturer's guidelines to ensure optimal performance and prevent overheating.

Does the laminator come with any safety features?

Yes, the Fellowes Saturn 3i 95 Laminator often features advanced safety mechanisms, including a heat guard to protect users from accidental contact with the heated rollers.

Does the laminator offer both hot and cold lamination options?

The Fellowes Saturn 3i 95 Laminator generally supports only hot lamination, which uses heat to bond the pouch to the document. Cold lamination, which doesn't involve heat, might not be supported by this model.

Is the Saturn 3i 95 laminator easy to operate?

Yes, the Fellowes Saturn 3i 95 Laminator is user-friendly and straightforward to operate, making it suitable for both beginners and experienced users. It typically comes with clear instructions for setup and use.

References:Fellowes Saturn 3i 95 Thermal Laminator Machine – Device.report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>