NOCO GENIUS GENIUS5UK Smart Car Charger User Guide
- June 12, 2024
- NOCO genius
Table of Contents
NOCO GENIUS GENIUS5UK Smart Car Charger
Product Information
The product is the GENIUS5UK, an electrical device that can be used for charging batteries. It has seven charging modes: Standby, 12V, 12V AGM, 12V LITHIUM, 6V, REPAIR, and FORCE. The charger is designed to be safe and efficient, but it is important to follow the safety instructions to prevent electrical shock, explosion, fire, and other potential hazards.
Safety Instructions
- Read and understand all safety information before using the product.
- Do not cut power cords.
- Do not submerge the product in water or get it wet.
- Do not leave the product unattended while in use.
- Do not attempt to jump-start a damaged or frozen battery.
- Operate the product in well-ventilated areas.
- Do not cover the product.
- Avoid smoking or using any sources of electrical spark or fire when operating the product.
- Keep the product away from combustible materials. Wear eye protection when operating the product.
- If any battery acid comes in contact with your eyes or skin, flush the affected area with running clean water and contact poison control immediately.
- Working in the vicinity of a lead-acid battery is dangerous due to explosive gases. Follow all safety instructions provided by the battery manufacturer and any equipment used near the battery.
Product Usage Instructions
Before using the GENIUS5UK charger, it is important to understand the different charging modes and select the appropriate mode for your battery. The charger has the following charging modes:
- Standby Mode: In this mode, the charger is not charging or providing power to the battery. Energy Save is activated, drawing minimal power from the electrical outlet. Canbus is enabled in Standby mode. The orange Standby LED will illuminate.
- 12V Mode: This mode is for charging 12-volt Wet Cell, Gel Cell, Enhanced Flooded, Maintenance-Free, and Calcium batteries. The 12V white LED will illuminate when this mode is selected.
- 12V AGM Mode: This mode is for charging 12-volt AGM batteries. The 12V AGM white LED will illuminate when this mode is selected.
- 12V Lithium Mode: This mode is for charging 12-volt lithium-ion batteries, including lithium iron phosphate batteries with Battery Management Systems (BMS). The 12V Lithium blue LED will illuminate when this mode is selected.
- 6V Mode: This mode is for charging 6-volt batteries.
- REPAIR Mode: This mode is an advanced charging mode that requires pressing and holding for three seconds. It is used for repairing or recovering deeply discharged batteries.
- FORCE Mode: This mode is an advanced charging mode that requires pressing and holding for five seconds. It is used for force-charging batteries that are severely discharged or sulfated.
When using the GENIUS5UK charger, follow these steps:
- Ensure you have read and understood all safety instructions.
- Connect the charger to a power outlet.
- Select the appropriate charging mode for your battery based on the descriptions provided above.
- Confirm the selected mode by checking the corresponding LED indicator.
- Connect the charger to the battery, ensuring proper polarity.
- Monitor the charging process and ensure proper ventilation.
- Once the battery is fully charged, disconnect the charger from the battery and the power outlet.
For more information and support, visit the official website of the product manufacturer.
Important Safety Warnings
About GENIUS5
The NOCO GENIUS5 represents some of the most innovative and advanced
technology on the market, making each charge simple and easy. It is quite
possibly the safest and most efficient charger you will ever use. The GENIUS5
is designed for charging all types of 6V & 12V lead-acid batteries, including
Lithium (LiFePO4), Wet (Flooded), Gel, MF (Maintenance-Free), CA (Calcium),
EFB (Enhanced Flooded Battery), and AGM (Absorption Glass Mat) batteries. It
is suitable for charging battery capacities up to 120 Amp-Hours and
maintaining all battery sizes.
Getting Started
Before using the charger, carefully read the battery manufacturer’s
specific precautions and recommended rates of charge for the battery. Make
sure to determine the voltage and chemistry of the battery by referring to
your battery owner’s manual prior to charging.
Mounting
It is important to keep in mind the distance to the battery. The DC cable
length from the charger, with either the battery clamp or eyelet terminal
connectors, is approximately 77.7 inches (1973.6mm). Allow for 12 inches
(304mm) of slack between connections. Proposition 65.
WARNING : This product can expose you to chemicals including lead and exhaust fumes, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Personal Precaution
Only use the product as intended. Someone should be within range of your
voice or close enough to come to your aid in case of emergency. Have a supply
of clean water and soap nearby in the case of battery acid contamination. Wear
complete eye protection and protective clothing while working near a battery.
Always wash hands after handling batteries and related materials. Do not
handle or wear any metal objects when working with batteries including; tools,
watches or jewelry. If metal is dropped onto the battery, it may spark or
create a short circuit resulting in electrical shock, fire, or explosion which
may result in injury, death or property damage.
Minors
If the product is intended by “Purchaser” to be used by a minor, purchasing
adult agrees to provide detailed instructions and warnings to any minor prior
to use. Failure to do so is the sole responsibility of the “Purchaser,” who
agrees to indemnify NOCO for any unintended use or misuse by a minor.
Choking Hazard
Accessories may present a choking hazard to children. Do not leave children
unattended with product or any accessory. The product is not a toy.
Handling
Handle product with care. The product can become damaged if impacted. Do not
use a damaged product, including, but not limited to, cracks to the casing or
damaged cables. Do not use the product with a damaged power cord. Humidity and
liquids may damage the product. Do not handle product or any electrical
components near any liquid. Store and operate products in dry locations. Do
not operate the product if it becomes wet. If the product is already operating
and becomes wet, disconnect it from the battery and discontinue use
immediately. Do not disconnect the product by pulling on the cables.
Modifications
Do not attempt to alter, modify or repair any part of the product.
Disassembling a product may cause injury, death or damage to property. If a
product becomes damaged, malfunctions or comes in contact with any liquid,
discontinue use, and contact NOCO. Any modifications to the product will void
your warranty.
Accessories
This product is only approved for use with NOCO accessories. NOCO is not
responsible for user safety or damage when using accessories not approved by
NOCO.
Location
Prevent battery acid from coming in contact with the product. Do not operate
the product in a closed-in area or an area with restricted ventilation. Do not
set a battery on top of product. Position cable leads to avoid accidental
damage by moving vehicle parts (including hoods and doors), moving engine
parts (including fan blades, belts, and pulleys), or what could become a
hazard that may cause injury or death.
Operating Temperature
This product is designed to work in ambient temperatures between -4° F and
104° F (-20° C and 40° C). Do not operate outside of temperature ranges. Do
not charge a frozen battery. Discontinue use of product immediately if the
battery becomes excessively warm.
Storage
Do not use or store your product in areas with high concentrations of dust or
airborne materials. Store your product on flat; secure surfaces so it’s not
prone to falling. Store your product in a dry location. The storage
temperature is -20° to 25°C (average under-hood temperature). Never exceed
80ºC under any condition.
Compatibility
The product is only compatible with 6V & 12-volt Lead-Acid, AGM, and Lithium
batteries. Do not attempt to use product with any other type of battery.
Charging other battery chemistries may result in injury, death or property
damage. Contact the battery manufacturer prior to attempting to charge the
battery.
Medical Devices
Do not charge pacemakers or other medical devices. Product may emit
electromagnetic fields. Product contains magnetic components which may
interfere with pacemakers, defibrillators, or other medical devises. These
electromagnetic fields may interfere with pacemakers or other medical devices.
Consult with your physician prior to use if you have any medical device
including pacemakers. If you suspect the product is interfering with a medical
device, stop using the product immediately and consult your physician.
Cleaning
Power off the product before attempting any maintenance or cleaning. Clean
and dry product immediately if it comes in contact with liquid or any type of
contaminant. Use a soft, lint-free (microfiber) cloth. Avoid getting moisture
in openings.
Explosive Atmospheres
Obey all signs and instructions. Do not operate product in any area with a
potentially explosive atmosphere, including fueling areas or areas which
contain chemicals or particles such as grain, dust or metal powders.
High-Consequence Activities
This product is not intended for use where the failure of the product could
lead to injury, death or severe environmental damage.
Radio Frequency Interference
Product is designed, tested, and manufactured to comply with regulations
governing radio frequency emissions. Such emissions from the product can
negatively affect the operation of other electronic equipment, causing them to
malfunction.
Model Number: Genius5
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. NOTE: This
equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his/her own expense.
How To Use
Charging Modes
The GENIUS5 has seven (7) modes: Standby, 12V, 12V AGM, 12V LITHIUM, 6V, REPAIR and FORCE. Some charge modes must be pressed and held for three (3) to five (5) seconds to enter the mode. These “Press and Hold” modes are advanced charging modes that require your full attention before selecting. It is important to understand the differences and purpose of each charge mode. Do not operate the charger until you confirm the appropriate charge mode for your battery. Below is a brief description:
Mode| Explanation (Peak Voltage Measured At 25°C, Amperage Rating Is
Bulk Amperage When Above 0°C)
---|---
Standby
| In Standby mode, the charger is not charging or providing any power to the
battery. Energy Save is activated during this mode, drawing microscopic power
from the electrical outlet. Canbus is enabled in Standby mode. When in
Standby, the orange Standby LED will illuminate.
No Power
| For charging 12-volt Wet Cell, Gel Cell, Enhanced Flooded, Maintenance-Free
and Calcium batteries. When selected, the 12V white LED will illuminate.
14.5V | 5A | Up To 120Ah Batteries
| For charging 12-volt AGM batteries. When selected, the 12V AGM white LED
will illuminate.
14.8V | 5A | Up To 120Ah Batteries
| For charging 12-volt lithium-ion batteries, including lithium iron
phosphate. When selected, the 12V Lithium blue LED will illuminate. For use on
batteries with Battery Management Systems (BMS) only.
14.6V | 5A | Up To 120Ah Batteries
Press & Hold (3 Seconds)| For charging 6-volt Wet Cell, Gel Cell, Enhanced
Flooded, Maintenance-Free and Calcium batteries. When selected, the 6V white
LED will illuminate.
7.25V | 5A | Up To 120Ah Batteries
Force Mode Press & Hold (5 Seconds)| For charging batteries with a voltage
lower than 1V. Press and Hold for five (5) seconds to enter Force Mode. The
selected charge mode will then operate under Force Mode for five (5) minutes
before returning to standard charging in the selected mode.
5A | Up To 120Ah Batteries
| An advanced battery recovery mode for repairing and restoring, old, idle,
damaged, stratified or sulfated batteries. When selected, a red LED will
illuminate and flash.
16.5V | 5A | Any Capacity [From Standby Press and Hold 3 Seconds With
Clamps Connected to the Battery]
Using 6V. [Press & Hold for 3 seconds]
6V charge mode is designed for 6-volt lead-acid batteries only, like Wet Cell, Gel Cell, Enhanced Flooded, Maintenance-Free and Calcium batteries. Press and hold for three (3) seconds to enter 6V Charge Mode. Consult the battery manufacturer before using this mode.
Using 12V Lithium
12V Lithium charge mode is designed for 12-volt lithium-ion batteries only, including lithium iron phosphate.
CAUTION. USE THIS MODE WITH EXTREME CARE. THIS MODE SHOULD ONLY BE USED WITH 12-VOLT LITHIUM BATTERIES THAT HAVE A BUILT-IN BATTERY MANAGEMENT SYSTEM (BMS). LITHIUM-ION BATTERIES ARE MADE AND CONSTRUCTED IN DIFFERENT WAYS AND SOME MAY OR MAY NOT CONTAIN A BATTERY MANAGEMENT SYSTEM (BMS). CONSULT THE LITHIUM BATTERY MANUFACTURER BEFORE CHARGING AND ASK FOR RECOMMENDED CHARGING RATES AND VOLTAGES. SOME LITHIUM-ION BATTERIES MAY BE UNSTABLE AND UNSUITABLE FOR CHARGING.
Force Mode. [Press & Hold for 5 seconds]
Force mode allow the charger to manually begin charging when the connected battery’s voltage is too low to be detected. If battery voltage is too low for the charger to detect, press and hold the mode button for 5 seconds to activate Force Mode, then select the appropriate mode. All available modes will flash. Once a charge mode is selected, the Charge Mode LED and Charge LED will alternate between each other, indicating Force Mode is active. After five (5) minutes the charger will return to the normal charge operation and low voltage detection will be reactivated.
CAUTION:
USE THIS MODE WITH EXTREME CARE. FORCE MODE DISABLES SAFETY FEATURES AND
LIVE POWER IS PRESENT AT THE CONNECTORS. ENSURE ALL CONNECTIONS ARE MADE PRIOR
TO ENTERING FORCE MODE, AND DO NOT TOUCH CONNECTIONS TOGETHER. RISK OF SPARKS,
FIRE, EXPLOSION, PROPERTY DAMAGE, INJURY, AND DEATH.
Using 12V Repair. [From Standby Press and Hold 3 Seconds With Clamps Connected to the Battery]
12V Repair is an advanced battery recovery mode for repairing and storing, old, idle, damaged, stratified or sulfated batteries. Not all batteries can be recovered. Batteries tend to become damaged if kept at a low charge and/or never given the opportunity to receive a full charge. The most common battery problems are battery sulfation and stratification. Both battery sulfation and stratification will artificially raise the open circuit voltage of the battery, causing the battery to appear fully charged, while providing low capacity. Use 12V Repair in attempt to reverse these problems. For optimal results, take the 12-volt battery through a full charge cycle, bringing the battery to full charge, before using this mode. 12V Repair can take up to four (4) hours to complete the recovery process and will return to Standby when completed.
CAUTION:
USE THIS MODE WITH CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY.
THIS MODE USES A HIGH CHARGING VOLTAGE AND MAY CAUSE SOME WATER LOSS IN WET
(FLOODED) CELL BATTERIES. BE ADVISED, SOME BATTERIES AND ELECTRONICS MAY BE
SENSITIVE TO HIGH CHARGING VOLTAGES. TO MINIMIZE RISKS TO ELECTRONICS,
DISCONNECT THE BATTERY BEFORE USING THIS MODE.
Connecting to the Battery
Do not connect the AC power plug until all other connections are made. Identify the correct polarity of the battery terminals on the battery. Do not make any connections to the carburetor, fuel lines, or thin, sheet metal parts. The below instructions are for a negative ground system (most common). If your vehicle is a positive ground system (very uncommon), follow the below instructions in reverse order.
- Connect the positive (red) eyelet terminal connector to the positive (POS,P,+) battery terminal.
- Connect the negative (black) eyelet terminal connector to the negative (NEG,N,-) battery terminal.
- Connect the battery charger into a suitable electrical outlet. Do not face the battery when making this connection.
- When disconnecting, disconnect in the reverse sequence, removing the negative first (or positive first for positive ground systems).
Begin Charging
- Verify the voltage and chemistry of the battery.
- Confirm that you have connected the battery clamps or eyelet terminal connectors properly and the AC power plug is plugged into an electrical outlet.
- [First-time use] The charger can now be left connected to the battery at all times to provide maintenance charging.
- Press the mode button to toggle to the appropriate charge mode (press and hold for three seconds to enter an advanced charge mode) for the voltage and chemistry of your battery.
- The mode LED will illuminate the selected charge mode and the Charge LEDs will illuminate (depending on the health of the battery) indicating the charging process has started. 6.) The charger can now be left connected to the battery at all times to provide maintenance charging.
Auto-Memory:
The charger has built in auto-memory and will return to the last charge mode
when connected. To change modes after the first use, press the mode button.
Charging Times
The estimated time to charge a battery is shown below. The size of the battery
(Ah) and its depth of discharge (DOD) greatly affect its charging time. The
charge time is based on an average depth of discharge to a fully charged
battery and is for reference purposes only. Actual data may differ due to
battery conditions. The time to charge a normally discharged battery is based
on a 50% DOD. Temperature will also impact charging times. The GENIUS5
features thermal compensation that automatically adjusts charging profiles to
maximize charging performance.
Battery Size
Ah (Amp hour)
| Approximate Time to Charge In Hours
6V 12V
---|---
20| 3.0| 3.0
40| 6.0| 6.0
80| 12.0| 12.0
100| 15.0| 15.0
120| 18.0| 18.0
Understanding Charge LEDs
Understanding Error LEDs
Error Conditions will be indicated by the following LEDs.
PRODUCT DESCRIPTION
- Mode Button Push to cycle through charging Modes.
- Overvoltage Error LED Illuminates solid Red; Battery Voltage is above Protect voltage.
- Bad Battery Error LED Illuminates solid Red when connected battery will not hold a charge.
- Reverse Polarity Error LED Illuminates solid Red when reverse polarity is detected.
- Charge LED indicates the connected battery(s) state-of-charge.
- Standby LED Illuminates when the charger is in Standby Mode, the charger is not charging or providing any power to the battery.
- Repair Mode LED Illuminates solid Red when Repair mode is selected.
- Press and Hold» Mode LED Mode button must be pressed and held for 3 seconds to enter the mode.
- Mode LED Indicates the Charge Mode the charger is currently in. Push the MODE button to cycle through charge Modes.
Technical Specifications
- Input Voltage AC: 120-240 VAC, 50-60Hz
- Working Voltage AC: 120-240 VAC, 50-60Hz
- Output Power: 75 W Max
- Charging Voltage: Various
- Charging Current: 5A (12V), 5A (6V)
- Low-Voltage Detection: 1V (12V), 1V (6V)
- Back Current Drain: <0.5mA
- Ambient Temperature: -20°C to +40°C
- Type of Batteries: 6V, 12V
- Battery Chemistries: Wet, Gel, MF, CA, EFB, AGM, Calcium, Lithium
- Battery Capacity: Up to 120Ah, Maintains All Battery Sizes
- Housing Protection: IP65
- Cooling: Natural Convection
- Dimensions (L x W x H): 4.6 x 2.9 x 1.9 Inches
- Weight: 1.6 Pounds
DANGER
- READ AND UNDERSTAND ALL SAFETY INFORMATION BEFORE USING THIS PRODUCT. Failure to follow these safety instructions may result in ELECTRICAL SHOCK, EXPLOSION, FIRE, which may result in a SERIOUS INJURY, DEATH, or PROPERTY DAMAGE.
- Electrical Shock: The product is an electrical device that can shock and cause serious injury. Do not cut power cords. Do not submerge in water or get wet.
- Explosion: Unmonitored, incompatible, or damaged batteries can explode if used with product. Do not leave product unattended while in use. Do not attempt to charge a damaged or frozen battery. Use product only with batteries of recommended voltage. Operate product in well ventilated areas.
- Fire: The product is an electrical device that emits heat and is capable of causing burns. Do not cover product. Do not smoke or use any source of electrical spark or fire when operating product. Keep product away from combustible materials.
- Eye Injury: Wear eye protection when operating the product. Batteries can explode and cause flying debris. Battery acid can cause eye and skin irritation. In the case of contamination of eyes or skin, flush affected area with running clean water and contact poison control immediately.
- Explosive Gases: Working in the vicinity of a lead acid is dangerous. Batteries generate explosive gases during normal battery operation. To reduce risk of battery explosion, follow all safety information instructions and those published by the battery manufacturer and manufacturer of any equipment intended to be used in the vicinity of the battery Review cautionary markings on these products and on the engine.
3-Year Hassle-Free Warranty
NOCO warrants that this product (the “Product”) will be free from defects in material and workmanship for a period of Three (3) years from the date of purchase (the “Warranty Period”). For defects reported during the Warranty Period, NOCO will, at its discretion, and subject to NOCO’s technical support analysis, either repair or replace defective products. Replacement parts and products will be new or serviceably used, comparable in function and performance to the original part and warranted for the remainder of the original Warranty Period.
NOCO’S LIABILITY HEREUNDER IS EXPRESSLY LIMITED TO REPLACEMENT OR REPAIR. TO THE MAXIMUM EXTENT PERMITTED BY LAW, NOCO SHALL NOT BE LIABLE TO ANY PURCHASER OF THE PRODUCT OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR EXEMPLARY DAMAGES, INCLUDING, BUT NOT LIMITED
TO, LOST PROFITS, PROPERTY DAMAGE OR PERSONAL INJURY, RELATED IN ANY WAY TO THE PRODUCT, HOWSOEVER CAUSED, EVEN IF NOCO HAD KNOWLEDGE OF THE POSSIBILITY OF SUCH DAMAGES. THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THOSE ARISING FROM COURSE OF DEALING, USAGE OR TRADE PRACTICE. IN THE EVENT THAT ANY APPLICABLE LAWS IMPOSE WARRANTIES, CONDITIONS OR OBLIGATIONS THAT CANNOT BE EXCLUDED OR MODIFIED, THIS PARAGRAPH SHALL APPLY TO THE GREATEST EXTENT ALLOWED BY SUCH LAWS.
This Warranty is made solely for the benefit of the original purchaser of the Product from NOCO or from a NOCO-approved reseller or distributor and is not assignable or transferable. To assert a warranty claim, the purchaser must: (1) request and obtain a return merchandise authorization (“RMA”) number and return location information (the “Return Location”) from NOCO Support by emailing support@no.co or by calling 1.800.456.6626; and (2) send the Product, including RMA number, and receipt to the Return Location. DO NOT SEND IN PRODUCT WITHOUT FIRST OBTAINING AN RMA FROM NOCO SUPPORT.
The original purchaser is responsible (and must prepay) all packaging and transportation costs to ship products for warranty service.
NOTWITHSTANDING THE ABOVE, THIS HASSLE-FREE WARRANTY IS VOID AND DOES NOT APPLY TO PRODUCTS THAT: (a) are misused, mishandled, subjected to abuse or careless handling, accident, improperly stored, or operated under conditions of extreme voltage, temperature, shock, or vibration beyond NOCO’s recommendations for safe and effective use; (b) improperly installed, operated or maintained; (c) are/were modified without the express written consent of NOCO; (d) have been disassembled, altered or repaired by anyone other than NOCO; (e) the defects of which were reported after the Warranty Period.
THIS HASSLE-FREE WARRANTY DOES NOT COVER: (1) normal wear and tear; (2) cosmetic damage that does not affect functionality; or (3) Products where the NOCO serial number is missing, altered, or defaced.
HASSLE-FREE WARRANTY CONDITIONS
These conditions apply only to Product during the Warranty Period. The Hassle- Free Warranty is void either by elapsed time from date of purchase (elapsed time from serial number date, if no proof of purchase) or from the conditions listed earlier in this document. Return Product with the appropriate documentation.
With Receipt:
0-3 Years: NO Charge. With proof of purchase, The warranty period begins on date of purchase.
With NO Receipt:
0-3 Years: NO Charge. With NO proof of purchase, The warranty period begins on the serial number date.
We recommend registering your NOCO product in order to upload proof of purchase and extend your effective warranty dates. You may register your NOCO product online at: no.co/register. If you have any questions regarding your warranty or product, contact NOCO Support (email and phone number above) or write to: The NOCO Company, at 30339 Diamond Parkway, #102, Glenwillow, OH 44139 USA.
For more information and support visit: www.no.co/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>