VEVOR 1107 Head Pipe Adjustable Height Stand Instruction Manual
- June 12, 2024
- VEVOR
Table of Contents
VEVOR
Pipe Stand
Operating Instructions and Parts Manual
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
Description
Designed to support pipes for a variety of uses. Do not exceed the maximum
capacity of the product.
Inspection/Maintenance
Carefully inspect the stand prior to each use for proper assembly (such as the hand screw), wear, damage, or other issues that may affect safe usage. If any problems are found, discontinue use until the stand is repaired. Keep the stand clean and all moving parts lightly lubricated to aid in operation.
Operating Instructions and Parts Manual
General Safety Information
WARNING Read the warnings and instructions for all equipment being used
before operating this tool to reduce the risk of serious personal injury.
WARNING Failure to properly support the pipe may result in tipping of the
stand, dropping of the pipe, or serious injuries.
WARNING Use the appropriate safety equipment for the intended job such as
eye protection,hearing protection, feet protection, dusk masks, face shields,
etc to reduce the risk of injuries.
Installation and Operation
- Make sure that all equipment is inspected and set up accordingly.
- Make sure that the ground below the pipe stand is clear, stable, and level.
- The legs of the pipe stand should be fully open and the feet placed squarely on the floor.
- if the stand is equipped with rollers, ensure the rollers are properly adjusted for the pipe size
- Fasteners on the pipe stand should be evaluated and ensure that they are secured
- To adjust the height. grip head assembly, loosen the hand screw, and raise the lock ring to disengage the elevator tube. Move the head assembly to the desired height. Next, lower the lock ring until it engages the elevator tube, and securely tighten the hand screw. Do not raise the elevator tube past the hand screw or past the unit specifications. The jack screw can be used for fine adjustments to height. Do so by holding the head of the assembly station and carefully turning the jack screw handle to the desired height. Do not force the jack screw handle, as it may cause the screw to come loose from the stand.
- Position the stand(s) to properly support the pipe. The pipe should be supported in at least two places at all times. The number and placement of stands depends on the size, length, and weight of the pipe length.
- Carefully place the pipe on the stands. Make sure the pipe is properly centered on the stands to reduce the risk of tipping. Always stay clear of the supported load.
Attention
Make sure you can always see the screw through the observation holes.
Do not exceed the maximum line of the inner tube.
Tighten the safety nut can be more security
| | | |
---|---|---|---|---
Pipe Jack Stand With
V-Head| Pipe Jack Stand
With V-Head| Pipe Jack
Stand With V-Head| Pipe
Jack Stand With V-Head|
Pipe Jack Stand With
Roller-Head
1107| 1107B| 1107C| 1107S| 1109
| | | |
V-Head Pipe Jack Stand
with Casters| V-Head
Pipe Jack Stand with
Casters| V-Head Pipe
Jack Stand with Casters| V-Head
Pipe Jack Stand With 4-Ball|
V-Head Pipe Jack Stand With
2-Ball
1107AV| 1107BV| 1107CV| 1107B4-BALL| 1107C2-BALL
| | | |
V-Head Pipe Jack Stand
With 2-Ball| V-Head Pipe
Jack Stand With 4-Ball| V-Head
Pipe Jack Stand With 2-Ball|
V-Head Pipe Jack Stand With
4-Ball| V-Head Pipe Jack
Stand With 2-Ball
1107S2-BALL| 1107S4-BALL| 1107A2-BALL| 1107A4-BALL|
1107B2-BALL
| |
V-Head Pipe Jack Stand
With 2-Ball| V- Roller Head Pipe Stand| Mul-Function Jaw Stand
1107C4-BALL| 1106| 1108
Part Number| Pipe Capacity(In.)| Max Weight Capacity|
Overall Height (In.)
---|---|---|---
1107| 1/8 To 12| 2500 lbs| 28” To 52”
1107A2-BALL| 1/8 To 12| 1300lbs| 28” To 52”
1107A4-BALL| 1/8 To 12| 1500lbs| 28” To 52”
1107B| 1/8 To 12| 2500lbs| 24” To 42”
1107B2-BALL| 1/8 To 12| 1300lbs| 24” To 42”
1107B4-BALL| 1/8 To 12| 1500lbs| 24” To 42”
1107C| 1/8 To 12| 2500lbs| 20” To 37”
1107C2-BALL| 1/8 To 12| 1300lbs| 20” To 37”
1107C4-BALL| 1/8 To 12| 1500lbs| 20” To 37”
1107S| 1/8 To 12| 2500lbs| 28” To 52”
1107S2-BALL| 1/8 To 12| 1300lbs| 28” To 52”
1107S4-BALL| 1/8 To 12| 1500lbs| 28” To 52”
1109| 1/8 To 12| 2500lbs| 32” To 55”
1106| 1/8 To 24| 3000lbs| 28” To 52”
1108| | 300lbs| 32” To 45”
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>