Honeywell Home RDWL313P2000 Plug-In Wireless Doorbell with Strobe Light and Push Button Installation Guide
- June 7, 2024
- Honeywell Home
Table of Contents
Installation and Operation
Guide
Plug-In Wireless Doorbell
RDWL313P2000
Read before installing
Preparation
In the box, you will find
To install you will need
The push-button supplied with this kit is pre-programmed to operate with the
doorbell.
If it is not, see “Connect a Push Button” on page 4.
Overview
Just follow these simple steps:
- Install the push button battery and plug in the doorbell.
- Set up the doorbell and your preferences.
- Install the push button.
Power-up
- Choose an outlet location that is not near a heat source, where the doorbell will be easy to see and hear and plug in the doorbell.
- Open the push button battery cover and install the CR2032 battery.
Setup and Operation
Press the push button to test whether it is paired with the doorbell. The doorbell will light up and ring. If it does not, see “Connect a Push Button” on page 4.
Change the Light Setting
Press the Sunlight button to change the lights that flash when the doorbell
rings.
Press the Sunlight button
Change the Tune
Press the Music button to change the doorbell tune.
Every time you press the Music button, the tune will change. Stop pressing the
Music button when you hear the tune you want:
Ding Dong
Westminster
Piano
Fantasy
Soft Alert
Smart Sax
Adjust the Volume
Press the Volume Up or Volume Down buttons to adjust the volume of the
Doorbell.
Install Push Button
-
Mount the push button bracket in the desired location Use the screws
–OR–
Use the adhesive backing. If using the adhesive backing, clean the surface first. -
Snap the push button onto the mounting bracket.
Note: If you need to remove the push button, use a small screwdriver to release the tab.
Accessories
You can connect 4 accessories to your doorbell, including other pushbuttons,
window or door opening sensors, and motion sensors.
If you try to connect more accessories than the max number, the LED on the
side blinks red.
Connect a Motion Sensor
- Press and hold the Setting button on the doorbell for three seconds LED on the side turns on with an amber color.
- Within 20 seconds of pressing the Setting button, wave or make some other kind of motion in front of the motion sensor.
Connect a Push Button
Follow these steps to change the ring and light settings for an existing
doorbell, too.
-
Press and hold the Setting button on the doorbell for three seconds.
The LED on the side turns on with an amber color. -
Press the push button.
-
Within 12 seconds of pressing the push button, press the Music button to select the ring for that push button.
-
Within 12 seconds of pressing the doorbell, press the Sunlight button to select the light setting for that push button.
Secret Knock
You can set up a Secret Knock that makes a different ring and light setting
for each push button. The Secret Knock is triggered by pressing the push
button quickly 3 times.
- Press the push button 3 times quickly.
- Within 12 seconds of pressing the push button, press the Music button to select the ring for the Secret Knock
- Within 12 seconds of pressing the push button, press the Sunlight button to select a light setting for the Secret Knock.
Maintenance
Your doorbell and push-button require no maintenance except to periodically
change the battery.
If using the correct battery, its life should be approximate:
- Up to 2 years for the push button; replace with CR2032 lithium battery
Low Battery Notification
When the push-button batteries are low, two beep sounds are heard after the
normal tune.
Reset
This process removes all pairings, including the push button that came with
this doorbell:
- Unplug the doorbell.
- Press and hold the Setting button, and plug the doorbell back in at the same time.
- The doorbell will beep several times rapidly and is returned to its factory default settings.
Specifications
| Doorbell| Push Button
---|---|---
Operating Temperature| 23°F to 104°F (-5°C to 40°C)| -4°F to 122°F (-20°C to
50°C)
ActivLinliu| 916.8 MHz| 916.8 MHz
Range (open field)| 250 ft (76 m)| 250 ft. (76 m)
Sound Level (typical)| 84dBA| –
RF Power| –| <1.2W
Battery Type| Input 100-240V- 50-60Hz 300mA| CR2032
Battery Life (5 activations/day)| –| Up to 2 years
Rainproof| N/A| Pass UL1598 rain test.
Troubleshooting
| If | Then |
|---|---|
| The doorbell does not work | 1. Make sure the correct batteries (1 CR2032) are |
installed with the correct
polarity.
2. The doorbell might be out of range; try the doorbell in a different
location.
3. Reconnect the doorbell. See “Connect a Push Button”.
Two ‘beep’ sounds are heard after the normal tune| Replace the push button
battery with a new CR2032.
Range is reduced| 1. Metal structures including uPVC door frames can reduce
the range. Don’t
mount the doorbell or push the button on or near metal structures.
2. Move the doorbell closer to the push button.
3. Weak batteries will reduce range. In cold conditions (below 41ºF [5ºC]),
batteries may need to be replaced more often.
For help please visit honeywellhome.com or call 1-800-633-3991.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and your body.
IC Regulations
CAN ICES-3(B)/ NMB-3(B)
This device complies with Industry Canada licence‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
CAN ICES-3(B)/NMB-3(B)
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 millimeters between the radiator and your body.
The operation of this equipment is subject to the following two conditions:
(1) this equipment or device may not cause harmful interference, and (2) this
equipment or device must accept any interference, including interference that
may cause undesired operation.
1-year limited warranty
Resideo warrants this product, excluding battery, to be free from defects in
workmanship or materials, under normal use and service, for a period of one
(1) year from the date of first purchase by the original purchaser. If at any
time during the warranty period the product is determined to be defective due
to workmanship or materials, Resideo shall repair or replace it (at Resideo’s
option). If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the
place from which you purchased it; or
(ii) call Resideo Customer Care at
1-800-633-3991. Customer Care will make
the determination whether the product should be returned to the following
address: Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422,
or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty
shall not apply if it is shown by Resideo that the defect was caused by damage
that occurred while the product was in the possession of a consumer.
Resideo’s sole responsibility shall be to repair or replace the product within
the terms stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF
ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED,
OR ANY OTHER FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDE MAKES ON THIS PRODUCT. THE
DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE
ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to
you.
This warranty gives you specific legal rights, and you may have other rights
which vary from state to state. If you have any questions concerning this
warranty, please write Resideo Customer Care, 1985 Douglas Dr, Golden
Valley, MN 55422 or call
1-800-633-3991.
Resideo Inc., 1985 Douglas Drive North
Golden Valley, MN 55422
33-00193EFS—05 M.S. Rev. 01-20 | Printed in United States
This product is manufactured by Resideo Technologies, Inc., Golden Valley, MN,
1-800-633-3991
© 2020 Resideo Technologies, Inc. The Honeywell Home trademark is used under
license from Honeywell International Inc.
All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>