SCHNEIDER SCVC23400 Vacuum Power Ultimate Instruction Manual

SCVC23400 Vacuum Power Ultimate
Instruction Manual

SCVC23400 Vacuum Power Ultimate

**** Please read the following instructions carefully before using this device. Please keep these instructions for future reference.

IMPORTANT WARNINGS PLEASE READ THE SAFETY INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.

Safety instructions:

• The battery must be removed safely.

• Do not use it near stairs or on the balconies. This machine does not have any avoidance sensors.

• This unit can be used by children from 8 years old and people with physical, sensory, or mental skills or lack of experience and knowledge provided they have been placed under supervision or have received instructions for using the machine safely and that they understand the dangers.
  Children should not play with the appliance. The cleaning and maintenance by the user should not be made by children without supervision.

• This device is intended for domestic use only.

• This unit is suitable for low to medium-felt back carpets. It is not suitable for uneven floors or mixed carpets.

• Remove the side brush at the under-carpet cleaning to protect the side brush.

• If the adapter’s power cord is damaged, the adapter must be discarded.

• Recharge/battery / s only with the charger supplied by the manufacturer

• Use the device with the battery (s) specifically created (s) for this purpose. The use of any (s) other (s) battery (s) could cause an explosion or fire Please use an adapter to use this product only.

• Do not use wet or greasy dust.

• Before use, keep fragile items (glass, light, etc.) and other objects that could entangle the brushes(long hair, plastic bags, rope, wire, etc.).

• Do not sit on the machine and do not put heavy things on it.

• WARNING : Make sure the unit can function freely in the room (it is not blocked by an obstacle, it cannot fall over) and that there is no obstacle on which the device may tip and create a risk of danger (such as lighted candles or a vase filled with water).

• Regularly clean the machine.

• Empty the dust container.

• Load the machine without using it for three months.

• Recharge only in the situation of a low-power alarm or when the power is turned off. Use it after fully charged.

• The battery must be removed from the apparatus prior to its disposal; the device must be disconnected from the mains when removing the battery;

• Do not dispose of batteries with household waste. Eliminate them in accordance with local regulations.

• Recharge the battery / the robot only with the adapter provided with the device.

• The cable of this adapter external flexible cannot be replaced; in case of damage to the cord, it is necessary to put the adapter discarded and replaced it with an adapter of the same model.

• The appliance must be disconnected from the supply mains when removing the battery.

• This appliance contains batteries that are non-replaceable.

• WARNING : For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
  Detachable supply unit

• WARNING : Risk of entrapment hazard. Keep loose clothing, hair, finger, etc. away from the motorized brushes and nozzles.

• WARNING : the plug must be removed from the socket-outlet before cleaning or maintaining the appliance.

IMPORTANT
It is forbidden to replace the power cable by yourself if damaged.
If the device is dropped, please ask a qualified person to check it before using it again. Internal damage could cause accidents. For any kind of problems or repairs, please contact the customer service of the local distributor, manufacturer, or a qualified person to avoid danger.

Disposal and environmental responsibility
In order to be environmentally friendly, we encourage you to have your device correctly. You can contact your local authorities or recycling centers for more information.

Please read the user manual before use.
**** This product complies with the applicable requirements of the Directives 2014/35/EU (repealing Directive 73/23/EEC as amended by Directive 93/68/EEC) and 2014/30/EU (repealing Directive 89/336 / EEC)

DESCRIPTION OF THE DEVICE

Product Overview

A vacuum cleaner with centrifugal technology with an air-filtering sponge Double filtration, and high-efficiency cleaning, to achieve the best dust removal effect.
High-quality aluminum tube, light corrosion-resistant Overlength design, easy to deal with high places, cracks, and other difficult corners.

• Engine block
  

• Electric brush
  Flexible rotation, convenient operation.
  

• Dust sensor
  

Packaging contents

INSTRUCTIONS FOR USE

Installation instructions for aluminum tubes

• Push the end of the aluminum tube horizontally into the vacuum hole of the main machine to ensure that it is compact and not loosened and that the installation is successful after the sound of clacking is heard. (figure 1
• To remove the aluminum tube, hold the main body with one hand and pull it out with the other hand by pressing the button. (figure 2)
  

The electric brush installation instructions

• Push one end of the round brush mouth into the tube end of the air outlet to ensure it is tight and not loose; if the sound is heard, it is installed successfully (Figure 3).
• If you want to remove the brush, the brush is held in one hand, and the button is pressed by the other hand simultaneously, and the brush will be pulled out. (Figure 4)
• Electric brushes can also use the method of aluminum tube connection, and directly be installed on the host.
  

Accessories
Instructions for using the accessories
In addition to using the aluminum tube and the electric brush, you can use a 2- in-1 brush and the long nozzle to adapt the product to all situations (Fig. 5): – 2 in 1 brush
It is suitable for cleaning small rooms, gaps,s or irregular object surfaces, such as wall corners, alloy window frame gaps, home appliance interiors, drawers, car cushions, picture frames, ceilings, keyboards, etc.
The accessories can be inserted in 2 different ways: directly at the end of the flexible tube (Mode 1) or at the end of the motor block (Mode 2).
Mode 1: Take the long nozzle attachment, and insert it into the end of the aluminum tube until you hear a click that confirms installation. To remove it, pull directly on it.
Take the 2-in-1 brush accessory and do the same manipulation: insert it into the end of the aluminum tube until you hear a click that confirms installation.
To remove it, pull directly on it. (Figures 6 and 7) Mode 2: To insert the accessories directly into the engine block, repeat the operation (Figures 8 and 9).

Battery installation instructions
Install the battery into the machine in the direction of (Fig.10) and install it as (Fig.11) to ensure no loosening. If the sound is heard, it has been installed successfully.

ATTENTION:

For long-term use, keep the battery in a cool and dry place, and leave the battery in a semi-charged state. Please wrap the battery with a non-conductive material to avoid direct contact with the battery which may cause damage to the battery.

Usage

1. Preparation
   Before using, please install the battery and check if the battery is charged. If not, please charge it in time (refer to “product charge”), it can be used after recharging.
   According to the clean area, the accessories can be chosen as demanded.
   The company has been specially equipped with various accessories.
   According to the clean area, you can choose to use the clean area. (see “Annex Operation instructions” for details)

2. Starting work
   Press the “switch button”, and touch the button, and the machine will start to work, if you need to stop working, loosen the “switch button”. (Figure 12)
   

3. Product dumping ash
   After stopping the machine, tap the dust tray on the side of the dust barrel (Fig. 13) Open the cover, dump the dust, and close the dust-barrel cover. (Fig. 14)

4. Disassemble the filter core
   Rotate and remove the dust tray, you have access to the stainless steel filter, and turn it to remove it. Do the reverse to replace the stainless steel filter and the dustpan. (Fig. 15) Remove the filter element in the direction indicated by the arrow. (Fig. 16)

5. Product charging
   Connect the charger directly to the vacuum cleaner or charging station (Figure

17. and the other end to a wall outlet in your home. (Figure 18) About charging indicator
    In operation: the light is illuminated continuously.
    Partially charged: LED flashes.
    Fully charged: the light is illuminated continuously.

Note:
After the product leaves the factory every 3 months (in the case of conditions), please use our special charger to charge the battery for 3 hours (do not need to be fully charged).
Do not charge the battery for a long time, if you are still charging beyond normal charging time, please stop immediately, otherwise, there may be risks such as battery heating, deformation, or burning.
When the battery is not in service for a long time or when it is in deep discharge, it may decrease in the first few times. It is recommended to discharge fully after charging (usually more than 6 hours). It only needs to repeat the action twice.

CLEANING AND MAINTENANCE

In order not to affect the performance of the machine, it is recommended that you maintain its components on a regular basis.
Before cleaning the main body (the engine block) (the holding section), make sure the machine stops working and the product is not recharging.
Scrub with water or neutral detergent. Before scrubbing, ensure the cloth is dry. Do not infiltrate water into the internal parts of vacuum cleaners (Fig. 19) After cleaning, do not put it under direct sunlight or in a wet place.

√ Cleaning dust barrel
Once the amount of dust reaches the “MAX” value, please clear it as soon as possible and do not overfill it.
In order to make it easier to empty the dustbin, it is recommended that you remove the aluminum pipe or other accessories before cleaning.
After the machine is stopped, open the dust barrel cover and dump the dust. If any stubborn dirt is found in the inner wall of the dust barrel, please wipe it carefully with a wet rag.
After cleaning, close the dust barrel cover and make sure the lock button is in place.

Note:
After wiping the inner wall of the dust barrel with a wet rag, it is necessary to be placed it under the sun and then cover the dust barrel after thoroughly drying.
√ Cleaning the outlet filter
In order to ensure the performance of the product, it is recommended that you regularly clean it and replace it after 3-6 months. (depending on the usage), Press and hold down the dust barrel release button, remove the body and turn the cover, remove the sponge, and dust off the sponge filter. (see Fig. 16)
If dust is accumulated too much, wash it thoroughly and dry it before loading it into the main body.

NOTICE!
During washing the sponge filter, use cold water and dry it thoroughly (usually in sunlight for 24 hours, then put it back into the body. )

√ Cleaning brush
It is recommended that the brush be cleaned once after 4-5 times of operation with an electric brush:

1.  Turn off the power and remove the electric brush.
2. Flip the brush and turn the lock button on the fixed cover with a coin to open the lock. (Figure 20)
3. Remove the roller brush to fix the cover plate, lift one end of the roller brush and pull out the roller brush. (Figure 21)
4. Use a pair of scissors or another sharp instrument to remove tangled animal hair and other waste (Figure 22).
5. When the cleanup is complete, push one end of the rolling brush into the floor brush and then clip the other end into the floor brush. (Figure 23)
6. Cover the cover and lock it. Sorting and storage
   charging deck storage: easy to take, saving space. (Figure 24)
   Accessory storage: easy to take, easy to collect. (Figure 25)

TROUBLESHOOTING

Analysis and treatment of common faults.

contact our after-sales service for maintenance.
The motor operates with abnormal sound.| The main suction pipe or aluminum pipe is blocked.| Clear the obstacles inside the main suction pipe, aluminum pipe.
After excluding the above situation, the situation remains the same.| Please contact our after-sales service for maintenance.
The product cannot be recharged.| The main computer and charger interface are not well connected.| Please check and connect it well.
After excluding the above situation, the situation remains the same.| Please contact our after-sales service for maintenance.

If the above steps are not able to work properly with your device, please contact our after-sales service department for help.

TECHNICAL SPECIFICATIONS

| Technical parameter
---|---
Working voltage (V)| 25.2V
Rated power (W)| 400W
Battery capacity (mAh)| 2000mAh
Dust barrel capacity (L)| 0.6L
Once charging time (h)| Between 3 to 5 hours
Continuous operating time (min)| 7(High) 35(Low)
Product dimension (mm)| 369mm x 125mm x 227mm
Net weight (kg)| 2.65 kg

DISCLAIMER OF WARRANTY:

The warranty does not cover the worn parts of the product, nor the problems or damage resulting from:

• surface deterioration due to normal wear and tear of the product;
• defects or deterioration due to contact with liquids and corrosion caused by rust or the presence of insects;
• any incident, abuse, misuse, alteration, disassembly, or unauthorized repair
• improper maintenance, improper use concerning the product, or connection to an incorrect voltage;
• any use of accessories not supplied or not approved by the manufacturer.
  The guarantee will be canceled if the nameplate and/or serial number of the product are removed.

DISPOSAL

The presence of this logo on the product means that the disposal of the device is governed by Directive 2012/19 / EU dated July 4, 2012, relating to waste electrical and electronic equipment (WEEE).
Any hazardous substance contained in electrical or electronic equipment can have a potential impact on the environment and health during recycling. Consequently, at the end of the device’s useful life, it must not be disposed of with unsorted municipal waste.

Your role as an end consumer is essential in terms of reuse, recycling, and obtaining other types of value creation from this product. You have the choice of different collection and exchange systems organized by local authorities (recycling centers) and

Information for external power supplies for Commission Regulation 2019/1782/EU

| Value| Unit
---|---|---
Model identification| SAW15A-300-0500GD
Manufacturer’s name or trademark| Shenzhen Shi Ying Yuan Electronics Co., Ltd.
Input voltage| 100-240| V
Input AC frequency| 50/60| Hz
Output voltage| 30| V
Output current| 0.5| A
Output power| 15| W
Average active efficiency| >86.8| ok
Efficiency at low load (10 %)| >72| ok
No-load power consumption| <0.1| W

Imported by
SCHNEIDER CONSUMER GROUP
12 rue Jules Ferry, 93110 Rosny-sous-Bois, FRANCE

Documents / Resources

| SCHNEIDER SCVC23400 Vacuum Power Ultimate [pdf] Instruction Manual
SCVC23400 Vacuum Power Ultimate, SCVC23400, Vacuum Power Ultimate, Power Ultimate, Ultimate
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>