DISNEY EL14 Helmet for Pedal Cyclist or Skateboards and Rollerskates Owner’s Manual
- June 12, 2024
- DiSNEY
Table of Contents
DISNEY EL14 Helmet for Pedal Cyclist or Skateboards and Rollerskates
The helmet you have just purchased provides protection, whether on or off the road . To insure proper use of this helmet, familiarize yourself with its features, fit and care by carefully reading through this manual before wearing your new helmet.
PROTECTION AND VENTILATION
The outer shell allows the helmet to be rated one of the lightest helmets while providing excellent durability and integrity. The multiple vents with inner air channels draw the air throughout the helmet and over the brow for maximum cooling.
Fitting-adjustable bead ring
The helmet must fit properly to be effective. With a proper fit, the helmet
will not move back and forth or to the side while fastened. If the head ring
inside the helmet does not fit, simply tighten or loosen it. To ensure the
proper fit adjust the head ring to best conform to your head shape.
RETENTION SYSTEM
This helmet uses A retention system that is simple and can be buckled and
unbuckled without changing the adjustment. The straps must be snugly and
evenly tensioned. Place the helmet firmly on your head and fasten the buckle.
(See Figure B)
Notice which strap is loose. Tighten the loose strap after removing the
helmet. To tighten the chin strap, hold the buckle with one hand. Then pull
the excess strap through. (See Example A)
To tighten the rear strap pull excess from the rear of strap 2. Hold the
helmet with one hand. With the other hand, hold the strap where they pass
nnder your chin Then pull from side to side to balance the length of all four
straps. (See Example B) The helmet must sit firmly and level on your head.
(See Example C). To lower the front of the helmet to cover your forehead.
Tighten the chin strap and loosen the rear strap. To raise the front. Loosen
the chin strap and tighten the rear strap To check for proper tension, put on
the helmet and fasten the buckle open your mouth. You should feel the strap
pulling against your chin.
Then attempt to pull the helmet off the front and rear. If the helmet comes
off, increase strap tension and examine if thick enough pads are being used.
The helmet should not be able to roll forward or backward excessively. It
should not be possible to remove the helmet which out unfastening the buckle.
NOTE: Please check adjustment every time the helmet is worn
The IMPORTANT INFORMATION
This headgear is designed to adsorbed the energy of a blow by partial
destruction or damage itself. Even though such damage may not be visible, the
helmet should be destroyed or replaced, if it Is involved in an injury related
fall.
Unfortunately, some accidents result in head injury that cannot be prevented
by ANY helmet Depending on the type of impact even very low speeds can result
in a serious head injury or fatality Always ride with extreme caution and be
sure to read this manual thoroughly.
WARNING
This helmet is designed and intended exclusively for the use of pedal
cyclists, skateboarders and rollerskaters. It is not intended for and will not
provide adequate, safety protection if used during motorsport or moped use. No
helmet can protect the wearer against all unforeseeable impacts. However, for
maximum protection, the helmet must fit well and all retention straps must be
securely fastened. Do not modify or remove any of the original components of
this helmet other than recommended by the manufacturer. This helmet should not
be used by children whilst climbing or doing other activities when there is a
risk of hanging if the child gets trapped with the helmet.
FINAL CHECK
The important thing to remember is that the helmet fits snugly. If you can
tilt it forward or backward, you need to tighten the strap adjustment.
It is important for the helmet to fit snugly on your head and must be fastened
to provide maximum protection.
All adjustments should be checked each time the helmet is worn, making sure it
fits snugly at all times.
CARING FOR YOUR HELMET
Clean the headgear with mild soap and water only. The use of any hydrocarbons, clearing fluids, paints or decals can cause damage to the helmet and make it ineffective in the result of an accident.
KEEP HELMET OUT OF EXTREME HEAT
Helmets will be damaged if exposed to temperature exceeding 150°F. Dark
vehicles and storage bags can exceed this on very hot days. Heat damaged
helmet will have random disfigured areas where the texture appears bubbly and
uneven. If damaged, helmets should be destroyed and replaced immediately.
Maximum use is up until 5 years after the production date of this helmet.
Disposal: please dispose of the different materials separately Please check your local waste facilities for appropriate disposal of the different materials Enquiries can be made at your local city hall.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>