Disney QSDQS-O02 Open Ear BT Headphones Instruction Manual

Disney QSDQS-O02 Open Ear BT Headphones Instruction Manual

Packing List

• Head phone x2

• Charging Case X1

• Instructions Warranty Card x1

• Type-C Charging Cable X1

Product diagram

Product Parameters

BT version: V 5.4
Transmission Distance :>10 Meters
Driver Diameter: $ 14.2mm
Driver Impedance: 32 Ohms
Driver Sensitivity: 110db ±3db
Frequency Response Range: 20hz~20khz
Playback Time: ≈ 5 Hours
Battery Capacity (Headphone): 35mAh/3.7V
Charging Time (Headphones): ≈ 1.5 Hours
Cooperate With The Charging Compartment For Battery Life: ≈ 16Hours
Rated Input (Headphone): 5V-35mA
Battery Capacity (Charging Case): 200mAh/3.7V
Charging Time (Charging Case): ≈ 1.5 Hours
Rated Input (Charging Case): 5V-200mA

Charging guide:

1. Type-C USB charging cable, connect the charging case to the USB power interface for 5V/1A output.
2. If the earphones are placed in the charging case, charging the charging case can also charge the earphones.

Charging the earphones with a charging case (white light always on, full light off), charging with a charging case (White light single flashing, always on when fully charged).
Low battery state: When the charging compartment is low (below 3.1V), the white light will flash quickly and sound an alarm until the compartment runs out of battery and goes out.

Rated Input: 5V-35mA (Headphone)

Rated Input: 5V-200mA (Charging Case)

Tips

1. Except for the operation methods specifically marked in the manual, please do not try to disassemble or replace any parts in the earbuds.

2. Don’t put the earbuds in the water or any others liquid.
   The earbuds are not waterproof.

3. If any liquid enters the product by accidentally, please disconnect and remove the connection immediately.

4. Please make sure that there is no water on your hands when Installing or uninstalling the product to avoid electric shock.

5. Do not put the product near by the heat source or expose it to the fire source directly.

6. Do not put the product in the environment with strong electromagnetic force, otherwise it will cause product malfunction.

Headphone Lights And Warning Tones

sound
Power off_| Ice Blue Light Stays On For A Second And Goes Off.| Power off prompt sound
BT Disconnected| Back-to-back Mode: Main Ear White Ice Blue Alternately Flashing, Secondary Ear Off| BT disconnected prompt sound

Product Operating Instructions

1. Power on
   Method 1: Open the top cover of the charging case, take out the headset and turn it on automatically. Method 2: Long press the left/right power on button for 3 seconds.

2. Power_off
   Method 1: Put it back to the charging case, the headset will automatically turn off.
   Method 2: Long press the left/right multi-function button for 5 seconds to turn off the phone.

3. BT pairing and connection

4. Please keep the distance between the BT headset and the cell phone (or other BT-connected devices) within 1 meter, the closer the better.

5. Make sure the headset is in the off state, long press the multi-function key for about 3 seconds, it will automatically enter the pairing state after power on and wait for connection; (The left and right ear pairing is successful, beep: Left and right ear paired warning tone);

6. Turn on the BT function of the user’s cell phone (or other BT devices), and search or scan, at this time the phone will search for Search for all the BT devices in the neighborhood, click the name of the searched headset QS-002, after successful pairing and connection, you can make cell phone calls, listen to songs. Then you can make phone calls and listen to songs.

7. Clear Pairing
   Power on unconnected state: Left/right headset turns off after 5 consecutive clicks on the left/right headset (clears all information of pairing and connection)
   

Function key operation

• Normal Mode
  

• Music Mode
  

• Talk Mode
  

Names And Contents Of Hazardous Substances In Products

This form is compiled in acco dance with SJ/T 11364.0:Indicates that the content of the hazardous substance in all homogeneous materials of the part is in below the limit required byGB/T 26572.X:Indicates that the hazardous substance at least in a certain homogeneous material of the part exceeds The limit requirements specified in GB/T 26572.The parts marked with “X” on the form are all harmful due to the limitations of global technological development. Substitution of substances.
Printed circuit board components:
Including printed circuit boards and their parts,electronic components,etc.and depending on the product model,the earbuds you purchased may not contain all the above components.
| Electronic and electrical products sold in the People’s Republic of China must mark this LOGO, the number in the logo represents the product under normal use Environmental protection use period.

Warranty Statement

Disclaimer
This user manual does not have any form of guarantee, position expression or other implication. The mentioned products, specifications and information are for reference only, and the content will also be updated on the web at any time without additional separate notice.

Warranty statement:
The product attached to this document is guaranteed as follows:If the product is twelve (12) months from the date of purchase(“Warranty Period”), under normal conditions of use due to quality defects damaged, can be repaired. Free repair; free replacement if the manufacturer confirms that it cannot be repaired; repaired or replaced product. Continue to enjoy the warranty during the remaining warranty period (the shortest not less than 30 days) Purchased by sale the ticket date shall prevail; if the purchase date cannot be determined, the warranty period shall be 13 (13) months If you apply for a warranty, please call the product service hotline first and execute it in the manner instructed by us. When applying for warranty, you need to provide an accurate, complete and clearly filled out valid sales invoice.

The above guarantee does not apply to the following situations:

1. Exceeding the validity period of the three packs;
2. Altering the warranty card and product code does not match the product body;
3. Causes caused by misuse, abuse or improper transportation, use, maintenance or storage obstacles or damage;
4. Failure or damage caused by force majeure (such as earthquake, war, disas- ter,etc.) or accident bad;
5. The zipper and tower buckle are damaged due to excessive force;
6. Disconnection or tearing caused by excessive load;
7. Any damage caused by sharp objects;
8. Products with signs of burning of flooding;
9. Damage caused by unauthorized disassembly;
10. Aging, discoloration, abrasion, rupture and other losses that occur during the normal use of the product.
11. If the original identification label of the product is changed or damaged, this guarantee will become invalid.

The completeness and appearance of the product and accompanying materials are not within the scope of the guarantee. You should check on the spot and raise objections to any discrepancies.

The above guarantees are all guarantees we make regarding the products, and are only applicable in mainland China. Nothing in this document affects consumer rights that cannot be excluded or restricted under the law profit.

E-mail: service@keesion.com

FCC Warnning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance Ocm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>