elk Home 68234-1 Regalia 1 Light 18 inch Oil Rubbed Bronze Pendant Ceiling Light Installation Guide

elk Home 68234-1 Regalia 1 Light 18 inch Oil Rubbed Bronze Pendant

Ceiling Light

Product Information

• Product Name: Pendant Light Fixture
• Model Numbers: 68234/1, 68244/1, 68254/1
• Manufacturer: Elk Home

Product Usage Instructions

1. Disconnect Power: Before installation, disconnect power at the main fuse box to ensure safety.
2. Installation:
3. Remove all parts and packages from the box before assembly. If anything is missing, contact the retailer.
4. Pull the house wires out of the junction box for easy accessibility during installation.
5. Position the mounting bracket (A) with the threaded ends of the fixture mounting screws (E) facing down towards the floor.
6. Pull the house wires through the center hole in the mounting bracket (A).
7. Align the small holes in the mounting bracket (A) with the holes in the junction box.
8. Screw each junction box screw (B) into the holes in the mounting bracket (A) and into the holes in the junction box. Tighten the screws to secure the mounting bracket to the junction box. Ensure that the house wires are completely pulled through the hole in the mounting bracket and not pinched between the bracket and ceiling.
9. Screw the recommended bulb (E26 Edison bulb type, not included) into the socket. Verify the correct bulb wattage marked on the socket and do not exceed the maximum wattage.
10. Lower the large ring (G) over the top of the shade (K), followed by placing the small ring (H) on top of the shade.
11. Hold one arm (T) with the hook at the bottom and fit the hook over the bottom edge of the shade (K) and large ring (G). Align the hole in the top end of the arm (T) with the hole in the bracket at the top of the shade (K). Thread one thumbscrew (S) into the holes to secure the arm to the bracket. Repeat this step for the remaining arms (T).
12. Place the diffuser (L) at the bottom of the shade (K) and fit it between the arms (T). Fit the edge of the diffuser into the hook on the bottom of each arm (T).
13. Hold the last arm (T) with the hook at the bottom and fit it over the edge of the diffuser (L). Align the hole in the top end of the arm (T) with the hole in the bracket at the top of the shade (K). Thread on the thumbscrew (S) to secure the arm to the bracket. Tighten all thumbscrews (S) completely.
14. Pendant Assembly:
15. Push the fixture wires up through a 6-inch stem (P).
16. Pull the fixture wires taut and screw the bottom of the stem (P) onto the top of the fixture body (O). Ensure that the fixture wires are not pinched between the fixture body and stem.
17. Push the fixture wires up through the threaded pipe on the canopy (D) and pull them through. Screw the short stem (W) onto the threaded pipe on the canopy (D).
18. Semi-Flush Assembly:
19. Push the fixture wires up through the short stem (W). Pull the fixture wires taut and screw the bottom of the short stem (W) onto the top of the fixture body (O). Ensure that the fixture wires are not pinched between the fixture body and stem.
20. Push the fixture wires up through the threaded pipe on the canopy (D) and pull them through. Screw the short stem (W) onto the threaded pipe on the canopy (D).

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

ASSEMBLY INSTRUCTION

1. Carefully pull house wires out of junction box so they are easily accessible during installation.

2. Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing down towards floor.

3. Carefully pull house wires through center hole in mounting bracket (A).

4. Align small holes in mounting bracket (A) with holes in junction box.

5. Thread each junction box screw (B) into holes in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box. CAUTION: Make sure house wires are pulled completely through hole in mounting bracket. DO NOT pinch wires between mounting bracket and ceiling.

6. Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture. WARNING: DO NOT exceed maximum bulb wattage.

7. Lower large ring (G) down over top of shade (K).

8. Place small ring (H) down on top of shade (K).

9. Hold one arm (T) so hook is at the bottom. Fit hook at bottom of arm (T) over bottom edge of shade (K) and large ring (G).

10. Align hole in top end of arm (T) with hole in bracket at top of shade (K). Thread one thumbscrew (S) into hole in top end of arm (T) and into hole in bracket. DO NOT completely tighten thumbscrew (S). This will be done after all arms are assembled.

11. Repeat steps 9 and 10 to assemble two (2) more arms (T).

12. Carefully place diffuser (L) at bottom of shade (K). Fit diffuser (L) in between arms (T). Fit edge of diffuser (L) into hook on bottom of arm (T).

13. Hold last arm (T) so hook is at the bottom. Fit hook at bottom of arm (T) over edge of diffuser (L). Align hole in top end of arm (T) with hole in bracket at top of shade (K).

14. Thread on thumbscrew (S) into hole in top end of arm (T) and into hole in bracket.

15. Completely tighten all thumbscrews (S).

Pendant Assembly:

1. Carefully push fixture wires up through 6 inch stem (N). Pull fixture wires out of top of 6 inch stem (N). Pull fixture wires taut. Screw bottom of 6 inch stem (N) onto top of fixture body (O). DO NOT pinch fixture wires between fixture body and stem.
2. Carefully push fixture wires through remaining three 12 inch stems (M). Screw stems (M) together carefully keeping fixture wires taut. DO NOT pinch fixture wires between stems.
3. From last 12 inch stem (M), push fixture wires up through bottom of swivel (P). Screw swivel (P) on onto top of 12 inch stem (M).
4. Push fixture wires up through threaded pipe on canopy (D). Pull fixture wires through canopy (D). Screw threaded pipe on canopy (D) onto end of swivel (P).

Semi-Flush Assembly:
CAUTION: The 2.64 inch, short stem (W) must be used for the semi-flush assembly.

1. Carefully push fixture wires up through short stem (W). Pull fixture wires taut. Screw bottom of short stem (W) onto top of fixture body (O). DO NOT pinch fixture wires between fixture body and stem.

2. Push fixture wires up through threaded pipe on canopy (D). Pull fixture wires through canopy (D). Screw short stem (W) onto threaded pipe on canopy (D).

3. Strip 3/4” of insulation from ends of fixture wires.

4. Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
   Connect Supply (House) Ground Copper Wire to:

   Bare Copper Wire or,
   Bare Silver Wire or,
   Green Insulated Wire.

5. Twist end of house lead wire (black) and endof fixture lead wire together. Twist wire nut (C)onto ends of wires. Completely tighten wire nut(C). Twist end of house neutral wire (white) andend of fixture neutral wire together. Twist wirenut (C) onto ends of wires. Completely tightenwire nut (C). Reference chart to the right forcorrect wire connections.

6. Wrap electrical tape (not included) around wirenuts (C) and wires. Ensure wires are securelyfastened into wire nuts.

7. Carefully push all wires and wire nuts intojunction box.

8. Carefully raise fixture up to ceiling. Place canopy (D) of fixture over mounting bracket (A). Pass holes in canopy (D) over ends of fixture mounting screws (E).

9. Screw one threaded cap (F) onto end of each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.

ANY QUESTIONS CALL:

• 800-613-3261
• M-F 8:00AM-6:00PM ET

References

• elkhome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>