saxby lighting 78546 Sirio Frame Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

saxby lighting 78546 Sirio Frame
Product Information
Product Usage Instructions
Technical data
Care and Safety
Layout
Installation
Wiring
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 78546 Sirio Frame

saxby-lighting-78546-Sirio-Frame-product

Product Information

Technical data:

Supply Voltage: 220-240 V~, 50 Hz
Bulb Type: 40W LED module (SMD), 4000K
Energy efficiency class: D
Non-replaceable light source
Replaceable control gear by a professional
Conformity with all relevant UKCA Directive requirements
Conformity with all relevant EC Directive requirements
The power supply is Double Insulated and does not require connection to an Earth circuit

Care and Safety:

Always disconnect the product from the mains at least 10 minutes allowing to cool down before any maintenance or adjustment
Clean with a soft dry cloth, avoiding solvents or abrasive cleaners
Switch off the power supply before cleaning

Product Usage Instructions

Warning:

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the power supply and each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped, or damaged. The main supply cable must have a minimum cross-sectional area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking.

Installation:

Refer to Fig 1., Fig 2., Fig 3., and Fig 4. for installation diagrams.
Identify the wiring from your existing light fitting.
Connect the wiring to the approved double-insulated terminal block as follows:

Wiring:

Check that:

The mains supply is disconnected
The wires are stripped to a suitable length
The correct wires are connected to the corresponding terminals (Live, Neutral, Earth)
All connections are secure

Note: If you are unsure about the wiring or installation process, it is recommended to seek assistance from a professional.

For further information, please refer to the instruction manual.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.

Manufactured in the UK by BH17 7BY and in the EU by Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg. Visit www.saxbylighting.com for more information.

Technical data

Supply
Voltage: 220-240 V~, 50 Hz
Bulb 401 LED module (SMD), 4000K
Type: These products contain a light source of energy efficiency class D.

Non-replaceable light source

Replaceable control gear by a professional

Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
The power supply is Double Insulated and does not require connection to an Earth circuit.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care and Safety

Always disconnect the product from the mains at least 10 minutes allowing to cool down before any maintenance or adjustment.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This power supply is Double Insulated and does not require connection to an Earth circuit.

Please read these instructions carefully before commencing any work.
This unit must be ﬁtted by a competent and qualiﬁed electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
Ensure that there is adequate ventilation for the LED Driver.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the power supply and each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged. The mains supply cable must have a minimum cross sectional area of 1.0mm2 Cables must be protected using suitable conduit or plastic trunking.

Installation

Existing ﬁttings must be completely removed before installation of a new product. Before removing the existing ﬁtting, carefully note the position of each set of wires.
Note that the switch is turned off before installation. The mounting surface must be flat and smooth to ensure a good fit.

Put the frame light upon the ceiling. See Fig 1.
lay the frame flat on the keel, the luminous face should be facing down. See Fig 2.
Wire and driver should be put on the side ceiling and the driver should be connected to the power supply. See Fig 3.
Placing one ceiling board flat on the frame light, be careful not to press on the wire. See Fig 4.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Wiring

Having correctly identified the wiring from your existing light fitting, connect to the approved double-insulated terminal block in the following way:

Check that