eurolite 51914253 LED IP Tourlight 200 WW User Manual

: June 12, 2024
: eurolite

Table of Contents

INTRODUCTION
SAFETY INSTRUCTIONS
DESCRIPTION OF THE DEVICE
INSTALLATION
DMX CONNECTION
POWER SUPPLY
OPERATION
CLEANING AND MAINTENANCE
PROTECTING THE ENVIRONMENT
TECHNICAL SPECIFICATIONS
Accessories
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

eurolite 51914253 LED IP Tourlight 200 WW

eurolite 51914253 LED IP Tourlight 200 WW

INTRODUCTION

DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing.

Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to

be qualified
follow the instructions of this manual
consider this manual to be part of the total product
keep this manual for the entire service life of the product
pass this manual on to every further owner or user of the product
download the latest version of the user manual from the Internet

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features
Silent IP65 spotlight with warm white 200 W LED, QuickDMX, CRI >90

High light output for stage and light installations
Chip-on-board technology makes for homogeneous light beam
For indoor and outdoor use (IP65)
Beam angle 30°
Stand-alone, master/slave and DMX mode
Integrated QuickDMX transceiver for wireless DMX control
4 Built-in show programs in auto mode
Electronic dimmer (0-100%)
Strobe effect 0-10 Hz
Control panel with LC display for easy configuration
Convenient wireless control via included IR remote control
Swivel mounting bracket
Additional bracket for floor use
Mains input and output for power linking up to 8 units
Incl. quick-lock Omega bracket
Barndoors optional

SAFETY INSTRUCTIONS

WARNING!
Please read the safety warnings carefully and only use the product as describe in this manual to avoid accidental injury or damage.

Intended use

This product is designed to light indoor and outdoor areas and is IP65 rated. It can be mounted and operated in indoor and outdoor areas. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
The integrated Quick DMX transceiver for wireless reception of DMX512 signals operates in the 2.4 GHz ISM range and is license-free and generally approved for operation in EU and EFTA countries.
Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper use or noncompliance with the safety instructions. In such cases, the warranty/guarantee will be null and void.
Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never defeat the protective ground of a mains cable. Failure to do so could result in damage to the device and possibly injure the user.
For outdoor use make sure to connect a rubber cable H05RN-F or HO5RR-F. For installations in the ground an underground power cable NYY must be used. All valid instructions concerning the installation of cables outdoors or in the ground must be adhered to.
The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
Do not expose the device to any high temperatures, direct sunlight, strong vibrations or heavy mechanical stress.
Do not immerse the product in water, this will destroy it. Furthermore, this could cause a lethal electric shock!
Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, when the device has been dropped or malfunctions occur.

Danger to children and people with restricted abilities

This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and fire

The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
The housing temperature (Tc) can be up to 80°C during use. Avoid contact by persons and materials.
Do not illuminate surfaces within 20 cm of the device. This value is indicated on the device by the symbol.
Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.

Warning – risk of injuries

Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60598-2-17.
If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer. Improper installation can result in bodily injury and or damage to property.
The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

This device must not be connected to the mains voltage by means of a dimmer.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
Never switch the device on and off at short intervals. This will considerably reduce the service life of the device.
If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
If a serial number label is affixed to the device, do not remove the label as this would make the guarantee void.

About batteries

Do not try to short-circuit, recharge, disassemble or heat batteries (danger of explosion!).
Remove the batteries if the device is not used for a longer period of time.
Damaged/leaking batteries may cause harm to your skin–use safety gloves.

DESCRIPTION OF THE DEVICE

Mounting brackets
200 W WW COB LED
Infrared sensor for the remotel control
Fixation screw
DMX input
Antenna for QuickDMX
LC display with operating buttons
DMX output
Pressure compensation plug
Power in
Safety eyelet
Power out

Note : When connected correctly, the power and DMX sockets are protected from spraying water according to IP65. When not in use, make absolutely sure to close the sockets with the rubber sealing caps.

INSTALLATION

WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations.

The device may be placed on the floor by unfolding the brackets or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
Block access below the work area and work from a stable platform when installing the device.
Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware.
Coupler
Quick-lock fastener
Omega bracket

Screw one coupler via an M10 screw and self-locking nut onto the Omega bracket. Insert the quick-lock fasteners of the Omega bracket into the respective holes on the mounting plate of the mounting bracket. Tighten the quick-lock fasteners fully clockwise.
Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. An appropriate eyelet is installed on the device for fixation of the safety bond. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
To align the device, release the fixation screws at the mounting bracket, adjust the desired inclination angle and tighten the fixation screws.
After installation, the device requires inspections periodically to prevent the possibility of rot, deformation and looseness.

DMX CONNECTION

Via DMX cable

A DMX512 data link is required in order to control the device via DMX. The device provides special DMX connectors, which are designed according to protection class IP65. Matching DMX connection cables with special plugs are optionally available. When not in use, make absolutely sure to close the connections with the rubber sealing caps to prevent moisture and dirt from penetrating.

Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.

XLR connection :

Wireless via QuickDMX
Connect the QuickDMX transmitter to the DMX controller. Put the transmitter and the IP Tourlight into operation and set them to the same transmission channel. Use menu option SET 2.4G on the spotlight to do this. Thus, the wireless DMX network is set up and the spotlight is paired to the QuickDMX transmitter. The assignment of the spotlight to the transmitter is kept memorized even after disconnecting the power supply.

Transmission modes
QuickDMX allows creating reliable point-to-point, point-to-multipoint and even multipoint-to-multipoint installations over large distances and in any environment (please refer to the transmitter’s documentation). A single QuickDMX transmitter transmits all 512 DMX channels to a maximum of 512 spotlights. It is possible to operate 6 transmitters at the same time in order to control a total of 3072 DMX channels. The maximum range is 400 m.

Point-to-point connection:

POWER SUPPLY

The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts. The power connectors are designed according to protection class IP65. Matching connection cables with special plugs are optionally available. When not in use, make absolutely sure to close the connections with the rubber sealing caps to prevent moisture and dirt from penetrating.

Connect the device via the mains cable to a grounded mains socket. Thus the unit is switched on.
To switch off the unit, disconnect the power plug.
Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.
The jack POWER OUT allows for power supply of further devices. To interconnect several devices, connect the jack POWER OUT to the input POWER IN of the next unit until all units are connected. In this manner, up to 8 devices can be linked at 230/240 input voltage and up to 4 devices at 110/115 input voltage.

OPERATION

After connecting the device to the mains it is ready for operation. The display indicates the last operating mode. The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains. The device can be operated in stand-alone mode via the control board and the EUROLITE IR-7 remote control or in DMX-controlled mode via any commercial DMX controller and QuickDMX with suitable wireless transmitter.

Operating buttons

Button	Function
MENU	Selects the operating mode or returns to the initial screen.
ENTER	Activates a value to be modified or saves a value when modifying.
UP	Selects the next menu item or increases values when modifying.
DOWN	Selects the previous menu item or decreases values when modifying.

Menu structure

Mode| Display Function
---|---
DMX mode| DMX| 4CH| ADDR:001-512| 4-channel mode and start address
2CH| ADDR:001-512| 2-channel mode and start address
1CH| ADDR:001-512| 1-channel mode and start address
Automatic mode| AUTO| 01-04| Auto programs 01-04
Running speed in

automatic mode

Stand-alone mode

Automatic mode
In automatic mode, 4 programs are available that run at an adjustable speed.

Press the MENU button so many times until AUTO is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to select the desired program (01-04). Confirm with the ENTER button.
Press the MENU button so many times until SPEED is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to adjust the running speed of the program from 01 (slow) to 09 (fast). Confirm with the ENTER button.

White color setting
The mode COLOR offers the possibility of adjusting the intensity of the warm white LED. The device will constantly emit the adjusted color.

Press the MENU so many times until COLOR is indicated in the display. Confirm with the ENTER button.
Now the display indicates the letter W for the warm white color and the corresponding intensity value. Use the buttons UP and DOWN to adjust the desired intensity.

Total brightness
Menu DIMMING allows adjusting the total brightness for all stand-alone operating modes.

Press the MENU button so many times until DIMMING is indicated in the display. Confirm with the ENTER button.
Use the buttons UP and DOWN to adjust the desired brightness (01 = dark, 99 = bright). Confirm with the ENTER button.

Fade in and out
FADING mode enables fade in and out. The speed is adjustable.

Press the MENU button so many times until FADING is indicated in the display. Confirm with the ENTER button.
Use the buttons UP and DOWN to adjust the desired speed (00-99). Confirm with the ENTER button.

Strobe effect
FLASH mode enables strobe effects. The flash frequency is adjustable.

Press the MENU button so many times until FLASH is indicated in the display Confirm with the ENTER button.
Use the buttons UP and DOWN to adjust the desired speed (00-99). Confirm with the ENTER button.

Behavior at missing DMX-signal
In DMX lost mode the program offers different options when no DMX signal is received.

Press the MENU button repeatedly until the display shows the DMX lost menu. Press ENTER to confirm.
Select the desired program with the UP and DOWN buttons (see Menu structure). Confirm with ENTER.

Cabled master/slave operation
Several devices may be interconnected (max. 32) via DMX cables. Then all slave units can be synchronized and controlled with the master unit without the need for a DMX controller. The devices must be set to the corresponding operating modes.

Configure all slave units before connecting the master unit: Press the MENU button so many times until SLAVE is indicated on the display. Confirm with the ENTER button.
Connect the DMX output of the master unit to the DMX input of the first slave unit. Then connect the DMX output of the first slave unit to the DMX input of the second slave unit, etc. until all units have been connected in a chain. Make sure the master unit is the first in the chain. Do not connect a DMX controller to the DMX input of the master unit.
Set the master unit to a stand-alone mode. The interconnected devices will now operate in synchronously.

Master/slave operation via QuickDMX

Set the master device and each slave device to the same transmission channel using the function SET 2.4G. Thus, the spotlights are paired.
Set the master unit to the desired operating mode and all slave units to SLAVE mode. The devices will now operate in synchronously.

Key lock
You can lock the operating buttons to e.g. prevent menu tampering. If the menu option PASSCODE is enabled, the buttons will be automatically locked from the last command. In order to disable the key lock function, press these buttons in the following order: UP, DOWN, UP, DOWN, ENTER.
QuickDMX transmission channel/Wireless 2.4G
You can use the SET 2.4G menu to set the wireless transmission channel for QuickDMX operation. Use the buttons UP and DOWN to choose wireless transmission channel with ON (QuickDMX enabled) or OFF (QuickDMX disabled). Confirm with the ENTER button. Please refer to the corresponding chapter for further explanation.

Remote control IR-7
The device must be activated for remote control. For this, set menu item INFRARED to ON. When actuating a button, always direct the remote control towards the sensor. There must be no obstacles between remote control and the sensor. In DMX and slave mode, the remote control functions are deactivated.

Button	Function
BLACKOUT	LEDs off
AUTO	Automatic mode program selection with (+)/(‒)
STROBE	Strobe effect for automatic mode flash rate setting with (+)/(‒)
SPEED	Running speed in automatic mode setting with (+)/(‒)
SENSITIVITY	Microphone sensitivity setting with (+)/(‒)
DMX	DMX mode on/off
MANUAL	White select: press MANUAL and W
FADE	Fade in/out speed setting with (+)/(‒)
1-9	Total brightness (1 = dark, 9 = bright)

Notes:

The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not possible.
If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right and at the same time remove the battery support. For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.
Remove the battery from the remote control as a precaution if the device is not used for a longer period of time.

DMX operation

Setting the number of DMX channels and the DMX starting address For operation with a controller with DMX512 protocol, the device is equipped with 4 control channels. However, it can also be switched to a mode with 1 or 2 channels if different functions are required. To be able to operate the device with a DMX controller, the DMX starting address must be set. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

Press the MENU button so many times until DMX is indicated in the display. Confirm with the ENTER button.
The display indicates 1 CH (1 DMX channels), 2 CH (2 DMX channels) or 4 CH (4 DMX channels). Use the buttons UP and DOWN to select the desired DMX channel mode. Confirm with the ENTER button.
Now the display indicates the menu item for the DMX start address ADDR***. Use the buttons UP and DOWN to set the address. Confirm with the ENTER button.
When receiving DMX control signals, the display shows “DMX”. If no DMX control signals are available, the display shows “NO SIGNAL”.

Note : Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain If several devices are addressed to the same address, they will work synchronously.

Functions in DMX mode

1-channel mode

Channel	Value	Function
1	000 – 255	Warm white 0-100%

2-channel mode

Channel	Value	Function
1 Master dimmer	000 – 255	Total brightness 0-100 %
2 Strobe effect	000 – 009	No function
010 – 255	Strobe effect slow > fast

4-channel mode

Channel	Value	Function
1 Master dimmer	000 – 255	Total brightness 0-100 %
2 Strobe effect	000 – 009	No function
010 – 255	Strobe effect slow > fast
3	000 – 255	Warm white 0-100%
4 Auto programs	000 – 009	No function
010 – 069	Auto program 1
070 – 129	Auto program 2 slow > fast
130 – 189	Auto program 3 slow > fast
190 – 255	Auto program 4 slow > fast

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness.

Disconnect the device from power and allow it to cool before cleaning.
Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
The device must be dry before reapplying power.

There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.

You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

Power supply:	100-240 V AC, 50/60 Hz
Power consumption:	110 W
IP classification:	IP65
Protection class:	Class I
Power connection:	Mains input IP T-Con (M)

Power supply cord with safety plug (provided)
Power output:| IP T-Con (F) mounting version
Lamp type:| LED lamp
LED:| 1 x COB (chip-on-board) 200 W warm white (WW)
DMX channels:| 1; 2; 4
DMX input:| 3-pin XLR (M) mounting version IP
DMX output:| 3-pin XLR (F) mounting version IP
Cooling:| Passive convection
Control:| Stand-alone; DMX; QuickDMX built-in; IR remote control; Master/slave function; Light Captain;
Beam angle (1/2 peak):| 30°
Beam angle (1/10 peak):| 60°
Color rendering index (CRI) more than:| 90 Ra
Housing color:| Black
Display type:| LCD
Dimensions:| Width: 25.1 cm
Depth: 27.2 cm
Height: 32.7 cm
Diameter: Ø 18.2 cm
Weight:| 4.50 kg
Remote control|
---|---
Battery:| 1 x Button cell 3.0 V CR2025 lithium manganese (provided)

Accessories

EUROLITE TPC-10 Coupler, silver	No. 59006856
EUROLITE Safety Bond A 4x1000mm up to 15kg silver	No. 58010320
EUROLITE Barndoors Theatre IP Tourlight	No. 51914259
EUROLITE Omega bracket 42	No. 51786558
PSSO DMX cable IP65 3pin 1.5m black	No. 3022783A
EUROLITE IP T-Con Power Cable 3×1.5 1,5m	No. 30235005
EUROLITE IP T-Con Connection Cable 3×1.5 1,5m	No. 30247750
EUROLITE IR-7 Remote Control	No. 50530561
EUROLITE QuickDMX Wireless Transmitter/Receiver	No. 70064703