VIMAR EIKON 20467 Pouch NFC RFID Connected IoT Instruction Manual

: June 12, 2024
: VIMAR

Table of Contents

EIKON 20467 Pouch NFC RFID Connected IoT
CHARACTERISTICS.
CONTROLLABLE LOADS.
OPERATION.
CONFIGURATION.
DEVICE RESET.
INSTALLATION RULES.
REGULATORY COMPLIANCE.
FRONT VIEW AND CONNECTIONS
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EIKON 20467 Pouch NFC RFID Connected IoT
Instruction Manual

LINEA
30813.x| EIKON
20467| ARKÉ
19467| PLANA
14467
---|---|---|---

EIKON 20467 Pouch NFC RFID Connected IoT

NFC/RFID smart card reader pocket for installation inside the room, IoT technology on Bluetooth® technology 5.0 standard for the creation of View Wireless mesh system, 1 relay output NO 16 A 100-240 V~ 50/60 Hz, 1 RGB LED visible in darkness with brightness control, 100-240 V~ 50/60 Hz power supply, grey – 2 modules.
The device should be installed in a location (for instance a hotel room, an office, etc.) and allows the activation of utilities only if the wireless smart card associated with it is read and recognized.
Using a smartphone or a tablet, the pocket can be configured with Bluetooth technology via the View Wireless App and can be supervised remotely by installing the gateway 30807.x-2059719597-16497-14597. It is designed to communicate with the landing reader 30812.x-20462- 19462-14462 (where associated during configuration) to manage accesses to the same room and ensure greater safety via the “Crossover relay” option.

CHARACTERISTICS.

Supply voltage: 100-240 V~, 50/60 Hz.
Max. power absorption from the mains: 1.1 W
White pocket lighting LED to be visible in darkness
RFID technology @ 13.56 MHz, ISO14443A Mifare standard
Frequency range: 13.553-13.567 MHz
RF transmission power: < 60 dBμA/m
Terminals:
- L and N for power supply.
- Relay output 16 A 240 V~ C-NO (NO SELV)
- IN input (not used)
1 configuration push button
Operating temperature: -10 °C – +45 °C (indoor use).
Protection degree: IP20.
Configuration via View Wireless App for Bluetooth technology system.
Frequency range: 2400-2483.5 MHz
RF transmission power: < 100mW (20dBm)

CONTROLLABLE LOADS.

Heating 16 (3,5) A (100.000 cycles)
- resistive loads : 16 A
- cos ø 0.6 motors: 3.5 A
Incandescent lamps : 5 A (20,000 cycles);
LED lamps :
- 100 W at 240 V~ (20,000 cycles);
  - 30 W at 100 V~ (20,000 cycles);
Fluorescent lamps : 0.5 A (20,000 cycles);
Electronic transformers : 4 A (20,000 cycles).

OPERATION.

The reader has two operating modes:

Recognition of the smart card inserted in the pocket activates the internal relay. When the card is removed, the relay switches to OFF after an amount of time which can be set during configuration.
If the pocket is associated with a landing reader and the “Crossover relay” option is active, when the card is inserted in the pocket, the reader relay stays ON, whereas when the card is removed, the relay switches OFF, and the amount of time can be set during the configuration. In this case, the door opening will be effected by the pocket relay to ensure greater safety.

CONFIGURATION.

In Bluetooth technology mode, the device must be configured using the View Wireless App.
For all the details please see the instruction manual for the View Wireless App.

DEVICE RESET.

Remove and restore the power supply to the device. Press the configuration push button for 30 s until the LED flashes white; release the button and wait for the LED to turn off.

INSTALLATION RULES.

Installation and configuration must be carried out by qualified persons in compliance with the current regulations regarding the installation of electrical equipment in the country where the products are installed.
Do not connect a SELV circuit to the C-NO terminals as there is no double insulation with on the L-N terminals.
The device and the load controlled must be protected against overloads by installing a device, fuse or automatic 1-way switch, with a rated current not exceeding 16 A.
Do not install two access control devices in the same mounting frame.

IMPORTANT:

We recommend installation on 2-module or 2 central module mounting frames; in the event of larger modular designs, considering the overall dimensions of the device, install it solely with the side blank module.
Wire the module before you attach it to the mounting frame.
The length of the cable for connection with the inputs must be no more than 30 m.

REGULATORY COMPLIANCE.

RED Directive. RoHS directive.
EN IEC 60669-2-1, EN 301 489-3 ,EN 300 330, EN 301 489-17, EN 300 328, EN 62479, EN
IEC 63000 standards.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is on the product sheet available on the following website: www.vimar.com
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.

WEEE – Information for users
If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not be included with other general waste at the end of its working life. The user must take the worn product to a sorted waste center, or return it to the retailer when purchasing a new one. Products for disposal can be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least 400 m2, if they measure less than 25 cm. An efficient sorted waste collection for the environmentally friendly disposal of the used device, or its subsequent recycling, helps avoid the potential negative effects on the environment and people’s health, and encourages the re-use and/or recycling of the construction materials.