AFX LIGHT BEAM-100LED-MKII LED Moving Head 100W with Dual Prism and Light Ring User Manual

June 12, 2024
AFX LIGHT

AFX LIGHT - logo BEAM-100LED-MKII
CODE: 16-2081
LED MOVING HEAD 100W
WITH DUAL PRISM & LIGHT RING

AFX LIGHT BEAM 100LED-MKII LED Moving Head 100W with Dual Prism and Light
Ring User Manual – p. 9

BEAM-100LED-MKII LED Moving Head 100W with Dual Prism and Light Ring

AFX LIGHT BEAM 100LED-MKII LED Moving Head 100W with Dual Prism and Light
Ring - CONNECTORSAFX LIGHT BEAM 100LED-MKII LED Moving Head 100W with Dual
Prism and Light Ring - CONNECTORS1AFX LIGHT BEAM 100LED-MKII LED
Moving Head 100W with Dual Prism and Light Ring -
DIAGRAM DIMENSIONSAFX LIGHT BEAM 100LED-MKII LED Moving Head 100W with Dual
Prism and Light Ring - DIMENSIONS DMX CHANNEL TABLE

Mode/Channel Value Function
22CH 24CH 30CH
1 1 1
0..255 PAN Movement
2 2 2
0..255 Fine control of Pan movement
3 3 3
0..255 TiltMovement
4 4 4
0..255 Finecontrolof Tilt movement
5 5 5
0..9 Open/ white
10..19 Colon
20..29 Color2
30..39 Color3
40..49 Color4
50..59 ‘ Color5
60..69 Color6
70..79 Color7
80..89 Color8
90..99 Color9
100. Color10
110..127 Color11
128..189 Forwardsrainboweffect fromfast toslow
190..193 Color rotation stop
194..255 Backwardsrainbow effect fromslow to fast
6 6 6
0..6 Open
7..13 gobo1
14..20 gobo2
21..27 gobo3
28..34 gobo4
35..41 gobo5
42..48 gobo6
49..55 gobo7
56..62 gobo8
63..69 gobo9
70..76 gobo10
6 6 6
--- --- ---
84..90 Bobo 12
91..97 gobo13
98..104 gobol4
105..111 Gobo1 shake slow to fast
112..118 Gobo2 shake slow to fast
119..125 Gobo 3 shake slow to fast
126..132 Gobo 4 shake slow to fast
133..139 Gobo 5 shake slow to fast
140..146 Gobo 6 shake slow to fast
147..153 Gobo 7 shake slow to fast
154..160 Gobo8 shake slowto fast
161..167 Gobo9 shake slow to fast
168..174 Gobo 10 shake slow to fast
175..181 Gobo 11 shake slow to fast
182..188 Gobo 12 shake slow to fast
189..195 Gobo 13 shake slow to fast
196..202 Gobo 14 shake slow to fast
203..255 Rot.gobo wheelcontsotation slow to fast
7 7 7
0..31 Shutter closed
32..63 shutter open
64..95 Strobe effect slow to fast
96..127 shutter open
128..159 Pulse – effect in sequences slow to fast
160..191 shutter open
192..223 Randomstrobe effect slow to fast
224..255 shutter open
8 8 8
0..255 Dimmer 0%…100%
9 9 9
0..255 In(near) to out(far)
10 10 10
0..5 Prism1swingout(hole)
6..127 Prism1swingin
128..189 Prism1Forwardsrotationfrom fast toslow
190..193 Prism1 rotation stop
194..255 Prism lBackwardsrotationfromslowtofast
11 11 11
0..5 Prism2 swingout(hole)
6..127 Prism2 swingin
11 11 11
--- --- ---
190..193 Prism2 rotation stop
194..255 Prism2Backwardsrotation fromslowtofast
12 12 12
0..199 Frostswingout
200..255 Frostswingin
13 13 13
0..225 Maxton minspeed
226..235 blackout by movement
236..245 blackoutbyallwheel changing
246..255 Nofunction
14 14 14
0..19 Nofunction
20..29 Nofunction
30..39 Nofunction
40..79 Nofunction
80..84 AllMotorreset
85..87 Scanmotorreset
88..90 Colorsmotorreset
91..93 Gobomotorreset
94..96 No function
97..99 Other motor reset
100..119 Internal program 1
120..139 Internal program 2
140..159 Internal program 3
160..179 Internal program 4
180..199 Internal program 5
200..219 Internal program 6
220..239 Internal program 7
240..255 Internal Sound program 1
Vector Mode
15 15
0..255 max to min speed
16 16
0..255 max to min speed
15 17 17
0..255 Pix_Dimmer 0%…100%
16 18 18
0..255 Pix_Strobe Speed0%…100%
17 19 19
0..255 0-100%Pix_Reddimmerfromdarkto bright
18 20 20
--- --- ---
0..255 0-100%Pix_Greendimmerfromdarktobright
19 21 21
0..255 0-100%Pix_Bluedimmer fromdarktobright
20 22 22
0..0 No Function
1..15 Red
16..31 Green
32..47 Blue
48..63 Red+Blue
64..79 Red+Green
80..95 Green+Blue
96..111 Red+Blue+Green
112..127 2700K
128..143 3200K
144..159 3500K
160..175 5000K
176..191 5500K
192..207 6000K
208..223 6500K
224..239 7000K
240..255 8000K
21 23 23
0..15 No Function
16..29 PixDynamic Scenel
30..43 PixDynamic Scene2
44..57 PixDynamic Scene3
58..71 PixDynamic Scene4
72..85 PixDynamic Scene5
86..99 PixDynamic Scene6
100..113 PixDynamic Scene7
114..127 PixDynamic Scene8
128..143 PixDynamic Scene9
142..155 PixDynamic Scene10
156..169 PixDynamic Scenell
170..183 PixDynamic Scenel2
184..197 PixDynamic Scenel3
198..211 PixDynamic Scenel4
212..225 PixDynamic Scenel5
226..239 PixDynamic Scenel6
240..255 PixDynamic Scenel7
22 24 24
--- --- ---
0..255 Slowto Fast
25
0..15 No Function
16..29 PixDynamic Scenel
30..43 PixDynamic Scene2
44..57 PixDynamic Scene3
58..71 PixDynamic Scene4
72..85 PixDynamic Scene5
86..99 PixDynamic Scene6
100..113 PixDynamic Scene7
114..127 PixDynamic Scene8
128..143 PixDynamic Scene9
142..155 PixDynamic Scene10
156..169 PixDynamic Scenell
170..183 PixDynamic Scenel2
184..197 PixDynamic Scenel3
198..211 PixDynamic Scenel4
212..225 PixDynamic Scenel5
226..239 PixDynamic Scenel6
240..255 PixDynamic Scenel7
26
0..255 Pix_ExpandPatterns Foreground dimmer0—100%.

(Foreground ColorSharewith “Pix_Macro”Channel)
| | 27| | Pix_Background dimmer
0..255| . Pix_ExpandPatterns Background dimmer0—100%.
| | 28| | Pix_Background Red
0..255| Pix_ExpandPatterns Background Red0—100%.
| | 29| | Pix_Background Green
0..255| r Pix_ExpandPatternsBackground Green0—100%.
| | 30| | Pix_Background Blue
0..255| Pix_ExpandPatternsBackground Blue0—100%.

UNPACKING INSTRUCTIONS

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present and have been received in good condition. Notify the freight company immediately and retain packing material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

CONTENTS OF THE CARTON

  • 1 x LED light effect
  • 2x omega clamp
  • 1x Powercon cable
  • 1x DMX lead
  • 1x User Manual

EXPLANATION OF SYMBOLS ON THE SILKSCREEN

CAUTION DO NOT OPEN THE HOUSING SHOCK HAZARD
The triangle containing a lightning symbol is used to indicate whenever your health is at risk (due to electrocution, for example).
** An exclamation mark in a triangle indicates particular risks in handling or operating the appliance.
The unit complies with UK standards For indoor use only 0.5m
Minimum distance between the appliance and other objects
Don’t stare into the light beam
IMPORTANT NOTE:** Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed.

Please read this manual carefully before operating this product.

SAFETY RECOMMENDATIONS

  • Please read these instructions carefully, they include important information about the installation, usage and maintenance of this product.
  • Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives this instruction booklet.
  • Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the bottom of the fixture.
  • The appliance is part of class I and must exclusively connected to an earthed mains outlet.
  • This product is intended for indoor use only!
  • To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating.
  • The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
  • The minimum distance luminaire from that part of the luminaire or lamp to the lighted object is 0.5m.
  • The max. ambient temperature (Ta) is 40°C. Don’t operate the fixture at higher temperatures.
  • The surface temperature of the unit may reach up to 85°C. DO NOT TOUCH the housing barehand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or servicing.
  • DO NOT OPEN the unit within 5 minutes after switching off.
  • In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
  • Make sure the power cord is never crimped or damaged.
  • Never disconnect the power cord by pulling or tugging on the cord.
  • Avoid direct eye exposure to the light source while it is on as sensitive persons may suffer an epileptic shock (especially meant for epileptics)!.
  • The product is for decorative purposes only and not suitable as a household room illumination.
  • If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
  • The lenses, housing or ultraviolet filter must be replaced if they are visibly damaged.
  • The light source of this device is not replaceable. If it is defective, the entire unit must be discarded.

DISCONNECT DEVICE

Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

FEATURES

  • 1 x 100W LED
  • 28 x 0.2W RGB SMD LEDs for the light ring
  • DMX, master-slave, sound-controlled and auto operation
  • 22/24/30 DMX channels
  • “Totem” mode
  • 1 colour wheel with 11 colours + open
  • 1 static gobo wheel with 14 gobo’s + open
  • Gobo shake
  • High precision optics with 2° projection angle
  • Electric focus over 2-3m
  • 16- & 24-facet prism with adjustable speed and direction
  • Smooth, accurate 8/16 bit PAN/TILT with inversion
  • Scan position memory with auto repositioning after an incident
  • Rainbow effect with adjustable direction and speed
  • Linear dimmer
  • 25x/sec high speed LED shutter/strobe effect with variable speed
  • Preset variable/random strobe and dimming pulse effect
  • 1.8″ TFT LCD display
  • Fan cooling
  • Management system with constant temperature readout
  • Mounting via 2 omega clamps & safety eyelet

FUSE REPLACEMENT

Disconnect the power cord before replacing a fuse and always replace with the same type fuse.
With a screwdriver wedge the fuse holder out of its housing.
Remove the damaged fuse from its holder and replace with exactly the same type of fuse.
Insert the fuse holder back in its place and reconnect power.
Warning: If after replacing the fuse you continue to blow fuses, STOP using the unit. Contact customer support for further instructions. Continuing to use the unit may cause serious damage.
CONTROL CONNECTION (FIG4)
Connect the provided XLR cable to the 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple moving heads together through serial linking. The cable needed should be 2-core, screened cable with XLR input and output connectors. Please refer to diagram 4.
DMX512 CONNECTION WITH DMX TERMINATOR
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX . This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminaotr is simply an XLR plug with a resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain. Please refer to diagram 4.
INSTALLATION (FIG.3)
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety rope. Never stand directly below the device when mounting, removing or servicing the fixture. This fixture may be mounted in any position provided there is adequate room for ventilation. The LED moving head provides a unique mounting bracket assembly that integrates the bottom of the base, the included ‘omega bracket’ and the safety cable rigging point in one unit (see illustration 3).When mounting this fixture on a truss, be sure to use an appropriate clamp with the included omega bracket using a M10 screw fitted through the center hole of the ‘omega bracket’. As an added safety measure, be sure to attach at least one properly rated safety cable to the fixture using one of the safety cable rigging points integrated in the base assembly.
POWER LINK
Connect an IEC cable from the POWER OUT connector of the 1st unit to the POWER IN connector of the second unit, etc.
CONTROL PANEL (FIG. 2)
To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach function you wish to change. When you reach the function you wish to change, press the ENTER button. When a function is selected, use the UP or DOWN buttons to change the function settings. Once your changes are made, press the ENTER button. Tip: Press UP & DOWN buttons at the same time for 3 seconds. The display will reverse.
FUNCTION MENU

MENU DESCRIPTION
DMX Mode DMX address
Channel Mode 22CH
24CH 24 channel mode
30CH 30 channel mode
Auto run Internal program 1-9
Music run Internal program
1-9 Master/Alone
SET Reset Default
--- ---
Signal set Wire

Reverse Pan
Reverse Tilt
Select Pan
Select Tilt| (on/off)
(on/off)
630/540/360
270/180/90| Reverse Pan
Reverse Tilt
Select Pan
Select Tilt
Mic sensitivity 0-99%
OFF signal mode (On/Off)
Scan quick mode
Totem mode OFF/CEN./R/L| Mic sensitivity
Off at original status and ON at reset status
Scan quick mode
Totem mode
Manu| Reset| Total reset
Pan/Tilt reset
Colour reset
Gobo reset
The others Reset| Reset All
Seset Pan/Tilt
Reset Colour
Reset gobo
Reset the others
Channel| PAN=XXX…| Channel control
ADV (Ad-vanced)
(Access code 0888)| Calibration
UID code| PAN=XXX…
XX XX XX XX X XX XX| Calibration
UID code

CLEANING

Due to fog residue, smoke, and dust cleaning the internal and external lenses should be carried out periodically to optimize light output.

  • Clean regularly the air vents and fans.
  • Use normal glass cleaner and a soft cloth to wipe down the out-side casing.
  • Clean the external optics with glass cleaner and a soft cloth every 20 days.
  • Always be sure to dry all parts completely before plugging the unit back in.

SPECIFICATIONS

Power supply ………………………………………………………………………………………………………..90-260V~50/60Hz
Consumption …………………………………………………………………………………………………………………………… 150W
PAN ……………………………………………………………………………………………………………………… 360° / 540° / 630°
TILT ………………………………………………………………………………………………………………………… 90° / 180° / 270°
Focus ……………………………………………………………………………………………………………………………………….. 2-3m
Signal In/out ………………………………………………………………………………………………………………………3-pin DMX
Power in/out ………………………………………………………………………………………………………………………. Powercon
Protection index …………………………………………………………………………………………………………………………. IP20
Dimensions …………………………………………………………………………………………………………299 x 184 x 423mm
Weight ………………………………………………………………………………………………………………………………………. 10kg

AFX LIGHT BEAM 100LED-MKII LED Moving Head 100W with Dual Prism and Light
Ring - QR Codehttps://www.lotronic.net/BEAM-100LED-MKII 
View the item on our website
© Copyright LOTRONIC 2022
Assembled in PRC
Designed by LOTRONIC S.A.
Av. Z. Gramme 9
B – 1480 Saintes

Documents / Resources

| AFX LIGHT BEAM-100LED-MKII LED Moving Head 100W with Dual Prism and Light Ring [pdf] User Manual
BEAM-100LED-MKII, BEAM-100LED-MKII LED Moving Head 100W with Dual Prism and Light Ring, LED Moving Head 100W with Dual Prism and Light Ring, Moving Head 100W with Dual Prism and Light Ring, 100W with Dual Prism and Light Ring, Dual Prism and Light Ring
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals