Artestia AR-88037 12 Volt Car Refrigerator User Manual

Artestia AR-88037 12 Volt Car Refrigerator

Safety Instructions

WARNING! Failure to obey these warnings could result in malfunction of your device and possible injury for yourself and other users.

• Do not operate the device if it is visibly damaged.
• Do not block the gaps of the device with things like pin, wire,
• Do not expose the device to rain or soak it in water
• Do not place the device near naked flames or other heat sources (heaters, direct sunlight, gas ovens )
• Do not store explosive substances like spray cans with flammable propellants in the device
• Before starting the device, ensure that the power supply line and the plug are dry
• Check if the voltage specification on the type plate matches that of the energy supply
• Once unpacked and before turning on, the device must be placed on a level surface for more than 6 hours
• Make sure that the device stays horizontally when it is running. The tilt angle must be less than 5° for long time running and be less than 45° for short time
• The refrigerator must be well ventilated for heat dissipation and make sure to keep some space around it. (Back Space 200mm, Side Space l 00mm)
• The device may only be repaired by qualified personnel. Improper repairs can lead to safety hazards. If the power cable is damaged, it must be replaced by the manufacturer, customer service or a similarly qualified person in order to prevent safety hazards

NOTICE!

• The device can be used by children aged 8 or over, as well as by persons with reduced physical, sensory or mental capabilities or a lack of experience and/or knowledge, providing they are supervised or have been taught how to use the device safely and are aware of the resulting risks.
• Children must be supervised to ensure that they do not play with the device.
• The installation of DC power in the boat must be handled by qualified electricians.
• Never pull the plug out of the socket by the cable
• Disconnect the device or switch it off when you turn off the engine. Otherwise you may discharge the battery.

CAUTION!

• Food is suggested to be stored in its original packaging or in suitable containers.
• Set suitable temperature for food or medicine stored in the device. Refer to recommended temperature for common food on Page4

Product Features

• High-efficiency DC compressor and conversion
• CFC free and great heat
• DC12/24V or AC 100~240V (using the adapter) power
• Fast cooling to -20°C/-4°F(based on 25°C/77°F room temperature).
• Intelligent battery protection
• Digital display for temperature
• Cup holder design and adjustable door opening direction.

Product Structure

Reverse door open direction

The door has two opening directions and can be taken off at an angle of 20°. When installing it back, align the door shaft with the compartment hole and then insert it.

Function and Operation

• Power supply: connect to DC 12V / 24V or AC 100~240V (using the adapter) power supply .
• Power On/Off: press to switch ON/ (Power light in red: compressor shutdown or delay start; power light in green: compressor is working
• Temperature Setting: press. up or down arrow for temperature setting , the setting will be saved automatically after stopping operating for 4 seconds (Note: the temperature displayed is the current temperature of the compartment, it’ II take a while to reach the set temperature.) Temperature setting range: -20~20°C( -4~68°F)
• Cooling Mode: under the running state, to switch HH(fast cooling mode, Eco/ Max light in red) and ECO(Energy saving mode, Eco/ Max light in green). (*Factory setting is HH.)
• Temperature Unit Setting: switch off the fridge, long for three seconds until El displays, keep pressing. until ES displays. then press A or T to select Celsius or Fahrenheit. (*Factory setting is 0 c.)
• Battery Protection Mode : under the running state, long forthree seconds until screen flashes, then press. again to select protection mode H3(High), H2(Middle) and Hl(Low) (*Factory setting is H3.)

Due to the different output voltages between vehicles, H3 should be set when the product is connected to car power, and H2 or Hl should be set when it is connected to a portable battery or other back-up battery.
The battery gear should be set from H3 to H2 or from H2 to Hl if there is a voltage protection code Fl shown on the panel. The battery gear should be set to H if the product keeps working after turning off the car engine, or the product may drain the battery

Voltage reference

INPUT

MODE

| DC 12V| DC 24V
---|---|---
CUT OUT| CUTIN| CUT OUT| CUTIN
Hl| 9.0V| 10.9V| 21.3V| 22.7V
H2| 10.lV| 11.4V| 22.3V| 23.7V
H3| 11.lV| 12.4V| 24.3V| 25.7V

the voltage is theoretical value, there may be a deviation in different sceneries

Reset: switch off the fridge, long press. for three seconds until El displays , under El mode, long press up down arrow **** at the same time until the screen displays “888”

Recommended temperature for common food

Cleaning and Storage

Cleaning

• Unplug the device first to avoid electric shock .
• Use wet cloth to clean the device and dry it.
• Do not soak the device in water and do not wash it directly.
• Do not use abrasive cleaning agents as these can damage the

Storag:

If the device will not be in use for a long time, please follow the steps :

• Turn off the power and remove the plug.
• Remove all the items stored in the
• Wipe off excess water from the fridge with a soft rag.
• Put the device in a cool and dry place.
• Leave the door slightly open to prevent odors from

Defrosting

Humidity can form frost in the interior of the cooling device or on the evaporator. This reduces the cooling capacity . Defrost the device in good time to avoid this.

• Switch off the device.
• Take out the contents of the device.
• Keep the door
• Wipe off the defrosted

Never use hard or sharp tools to remove ice or to loosen objects which have frozen in place.

Troubleshooting

Refrigerator does not work

| Check if the switch is on.
Check if the plug and socket are connected well.
Check if the fuse has been burnt.
Check if the power supply is malfunctioned.
Switching on/off the fridge frequently may cause start delay of the compressor.

Refrigerator compartments are too warm

| The door is opened frequently.
A large amount of warm or hot food was stored recently. Wait for the refrigerator to reach its selected temperature.
The refrigerator has been disconnected for a period of time.
Food is frozen| The temperature was set too low, please increase the temperature.
There is a “water flow” noise from inside the fridge| ****

It’s a normal phenomenon, caused by the flow of refrigerant.

There are waterdrops around the refrigerator casing or door gap|

It’s a normal phenomenon, the moisture will condense to water when it touches a cold surface of the refrigerator.

The compressor is slightly noisy when starting| It’s a normal phenomenon, the noise will be reduced after the compressor works stably.

Code Fl displayed

| Possible cause: low voltage to fridge.

Adjust the battery protection from H3 to H2 or from H2 to Hl.

Code F2 displayed

| Possible cause: condenser fan is overloaded. Disconnect power to fridge for 30 minutes & re-start.

Code F3 displayed

| Possible cause: compressor over pressure. Disconnect power to fridge for 30 minutes & re-start.

Code F4 displayed

| Possible cause: compressor not kicking in. Disconnect power to fridge for 30 minutes & re-start.
Code FS displayed| Possible cause: overheating of the compressor & electronics. Disconnect power to fridge for 30 minutes & re-sta rt .

Code F6 displayed

| Possible cause: no parameter can be detected by the controller. Disconnect power to fridge for 30 minutes & re-start.

Code F7 or FS displayed

| Possible cause: temperature sensor is faulty. Contact manufacturer for service .

Technical Information

Dimension(LWH)

| ****

587365368mm

23 1/8*14 3/8

*141/2 inches

| ****

587365438mm

23 1/ 8* 14 3/8

*171/4 inches

| ****

587365508mm

23 1/8*14 3/8

*20inches

Net Weight| 12kg/26.46Ib| 12.Skg/27.56/lb| 13kg/28.66Ib

Due to product improvement, the technical information might be different from actual information, please refer to the rating label on the product.

Disposal
Place the packaging material in the appropriate recycling waste bins wherever  possible.  If you wish to finally dispose of the product, ask your local recycling center or specialist dealer for details about how to do this in accordance with the applicable disposal regulations
We appreciate your order of Artestia products and your trust to our company. Customer satisfaction is our No. 1 priority. If you have any questions or find any problems, please do not hesitate to contact us at support@artestia.com. It’s always our pleasure to assist you to complete satisfaction

App Control

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>