eurolite LED CAT-80 Beam Effect with 80 W COB LED Cold White and Gobo Wheel User Manual
- June 12, 2024
- eurolite
Table of Contents
CAT-80 Beam Effect
with 80 W COB LED Cold White and Gobo Wheel
User Manual
 No.
51918595, black
No. 51918596, white
www.eurolite.de
LED CAT-80 Beam Effect with 80 W COB LED Cold White and Gobo Wheel
Diese Bedienungsanleitung gilt für die Artikelnummern / This user manual is
valid for the article numbers: 51918595, 51918596
Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter:
You can find the latest update of this user manual in the Internet under:
www.eurolite.de
DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a
dangerous electric shock when touching the wires. Never open the housing. Keep
the device away from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
INTRODUCTION
Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.
Product features
LED Beam Effect with 80 W COB LED in cold white and gobo wheel
- 3 different motion axes
- Rotating faceted mirror inside
- Rotating and swiveling mirror cylinder
- Generates countless moving patterns in the room
- Manual focus
- Electronic dimmer
- 1 powerful LED 80 W COB (chip-on-board) cold white (CW)
- Gobo wheel with static gobos; Focus manual
- Mirror cylinder effect; Strobe effect
- Rainbow effect with adjustable speed
- Gobo wheel with static gobos, 1 gobo, 8 color gobos and open
- Can be operated in 7 CH mode
- The device is cooled by cooling fan
- Controlling by stand-alone; Master/slave function; Sound to light via Microphone; DMX; QuickDMX via USB (optional); W-DMX by wireless solution via USB (optional); CRMX by LumenRadio via USB (optional)
- Preprogrammed in Light´J; Light Captain; EASY SHOW 2; EASY SHOW 3
- Flicker-free
- OLED display
SAFETY INSTRUCTIONS
WARNING!
Please read the safety warnings carefully and only use the product as
described in this manual to avoid accidental injury or damage.
Intended use
- This device is a spotlight for creating decorative lighting effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
- Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
- We do not assume any liability for material and personal damage caused by improper use or noncompliance with the safety instructions. In such cases, the warranty will be null and void.
- Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.
Danger due to electricity
- The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
- To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
- Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must be exactly the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
- The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
- Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
- The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
- Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
- Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
- Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
- Do not place any objects filled with liquids on the device.
- Do not place any open sources of fire, such as burning candles, on or directly next to the device.
- Make sure that objects cannot fall into the device, in particular metal parts.
- Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
- Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.
Danger to children and people with restricted abilities
- This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
- This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
Warning – risk of burns and fire
- The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
- The housing temperature (Tc) can be up to 85°C during use. Avoid contact by persons and materials.
- Do not illuminate surfaces within 10 cm of the device. This value is indicated on the device by the symbol.
- Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.
Warning – risk of injuries
-
Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
-
Make sure that the product is set up or installed safely and expertly and prevented from falling down.
Comply with the standards and rules that apply in your country, in particular EN 60598-2-17. -
If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer.
Improper installation can result in bodily injury and or damage to property. -
The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
-
For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
-
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
-
For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.
Caution – material damage
- This device must not be connected to the mains voltage by means of a dimmer.
- Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
- Never switch the device on and off in short intervals. This will considerably reduce the service life of the device.
- If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
- Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
- If a serial number label is affixed to the device, do not remove the label as this would make the warranty void.
DESCRIPTION OF THE DEVICE
- Mirror cylinder
- Housing
- Mounting bracket
- Fixation lever
- Manual focus
- Safety eyelet
- USB port for QuickDMX wireless receiver
- Power input
- DMX output
- DMX input
- Fuse holder
- Microphone for sound control
- OLED display with operating buttons
INSTALLATION
WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing
down. Make sure that the device is installed securely and cannot fall down.
The installation must be carried out by a specialist who is familiar with the
hazards and the relevant regulations.
The device may be placed on the floor or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.
- The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
- Block access below the work area and work from a stable platform when installing the device.
- Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware.
- Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. An appropriate eyelet is mounted on the device for fixation of the safety bond. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
- To align the device, release the fixation levers at the mounting bracket, adjust the desired inclination angle and tighten the fixation levers.
- After installation, the device requires inspections periodically to prevent the possibility of corrosion, deformation and looseness.
DMX512 CONNECTION
A DMX512 data link is required in
order to control the device via DMX. The device provides 3-pin XLR connectors
for DMX connection.
- Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
- Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
- At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
- If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.
XLR connections:
 Wireless
DMX transmission with QuickDMX
The device features an alternative DMX input for a QuickDMX receiver (sold separately). CRMX and WDMX receivers are compatible and can also be used. The connector allows a DMX control signal to be transmitted wirelessly to the device, eliminating the need for complex wiring to the DMX controller. The connector is designed as a USB port which provides the required 5 V operating voltage for the receiver.
Occupation of the USB port:
Connection to the mains
The device uses an auto-range power supply that accepts input voltages between
100 and 240 volts.
- Connect the device via the enclosed mains cable to a grounded mains socket. Thus the unit is switched on.
- To switch off the unit, disconnect the power plug.
- Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.
OPERATION
After connecting the device to the mains it is ready for operation. The
display indicates the last operating mode. The operating modes can be selected
by means of the display and the control buttons. All settings remain stored
even if the device is disconnected from the mains. The device can be operated
in stand-alone mode via the control board or in DMX-controlled mode via any
commercial DMX controller as well as wireless via QuickDMX with the optionally
available EUROLITE QuickDMX USB Wireless Transmitter/Receiver.
After you connected the effect to the mains, the LED CAT-80 Beam Effect starts
running. During the Reset, the motors are trimmed and the device is ready for
use afterwards.
The main menu is accessed by pressing the MENU button. Browse through the menu
by pressing the MENU button. Press the ENTER button in order to select the
desired menu. You can change the selection by pressing UP or DOWN. Confirm
every selection by pressing the ENTER button. The functions provided are
described in the following sections.
Menu structure
Main menu| Sub menu|
Function
---|---|---
Set Address| 001 – 506| Setting the DMX starting address
Mode Choice| Auto| Automatic show program
DMX| DMX mode
Sound| Sound controlled show program
Manu|
000 – 255| Dimmer Total brightness 0-100%
000 – 009| No function
010 – 255| Strobe Effect slow > fast
| Gobos
000 – 009| Open
010 – 019| Gobo1 – Red
020 – 029| Gobo2 – Light blue
030 – 039| Gobo3 – Yellow
040 – 049| Gobo4 – Orange
050 – 059| Gobo5 – Dark blue
060 – 069| Gobo6 – Magenta
070 – 079| Gobo7 – Green
080 – 089| Gobo8 – Pink / Light blue
090 – 098| Gobo9
099 – 255| Rainbow effect fast > slow
000 – 255| Flower Rotation slow > fast
000 – 255| Mirror Cylinder Rotation slow > fast
000 – 255| Horizontal Cylinder Movement, gradual adjustment of the mirror
cylinder position from left to right
Sensitive| 000 – 100| Microphone sensitivity with increasing sensitivity
Reset| | Motor reset
The display shuts off after a few seconds of inactivity.
Master/slave operation
Several devices may be interconnected (max. 32). Then all slave units can be
synchronized and controlled with the master unit without the need for a DMX
controller. The devices must be set to the corresponding operating modes.
- Configure all slave units before connecting the master unit. For this, set each slave device to the DMX address 001 and confirm with ENTER.
- Connect the DMX output of the master unit to the DMX input of the first slave unit. Then connect the DMX output of the first slave unit to the DMX input of the second slave unit, etc. until all units have been connected in a chain. Make sure the master unit is the first in the chain. Do not connect a DMX controller to the DMX input of the master unit.
- Select the desired show mode (Sound or Auto) at the master unit. The interconnected devices will now operate synchronously.
DMX operation
To be able to operate the device in DMX mode, it must first be set to DMX
under the Mode Choice menu item (see Menu structure).
Setting the DMX starting address
For operation with a controller with DMX512 protocol, the device is equipped
with 7 control channels. To be able to operate the device with a DMX
controller, the DMX starting address must be set. The starting address depends
upon which DMX controller is being used. Please refer to the controller’s
documentation.
- Press the UP or DOWN button so many times until DMX Address is indicated on the display. Confirm with the ENTER button.
- Now the display calls up the menu item for the DMX starting address: 001.
- Use the buttons UP and DOWN to set the address. Confirm with the ENTER button.
- The display will not flash if DMX signals are being received.
Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are addressed to the same address, they will work synchronously.
Overview for gobo wheel:
Functions in DMX mode
7-channel mode
Channel
| Value|
Function
---|---|---
1 Dimmer| 000 – 255| Total brightness 0-100%
2 Shutter / Strobe| 000 – 009| Off, Shutter closed
010 – 255| Strobe effect slow > fast
3 Gobo Wheel| 000 – 009| Open
010 – 019| Gobo1 – Red
020 – 029| Gobo2 – Light blue
030 – 039| Gobo3 – Yellow
040 – 049| Gobo4 – Orange
050 – 059| Gobo5 – Dark blue
060 – 069| Gobo6 – Magenta
070 – 079| Gobo7 – Green
080 – 089| Gobo8 – Pink / Light blue
090 – 098| Gobo9
099 – 255| Rainbow effect fast > slow
4 Flower Rotation| 000 – 009| No rotation
010 – 132| Forward rotation with increasing speed
133 – 255| Backward rotation with increasing speed
5 Mirror Cylinder Rotation| 000 – 009| No rotation
010 – 132| Forward rotation with increasing speed
133 – 255| Backward rotation with increasing speed
6 Horizontal Cylinder Movement|
000 – 255
|
Gradual adjustment of the mirror cylinder position from left to right
7 Auto Program / Reset| 000 – 009| No function
010 – 127| Automatic show program
128 – 255| Motor reset
CLEANING AND MAINTENANCE
The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness.
- Disconnect the device from power and allow it to cool before cleaning.
- Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
- The device must be dry before reapplying power.
There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of
same type and rating.
- Disconnect the device from power and allow it to cool.
- Open the fuse holder of the mains connection with a fitting screwdriver.
- Remove the old fuse from the fuse holder and replace it with a new fuse.
- Carefully push the fuse holder back into its position before reapplying power.
PROTECTING THE ENVIRONMENT
| Disposal of old equipment
When to be definitively put out of operation, take the product to a local
recycling plant for a disposal which is not harmful to the environment.
Devices marked with this symbol must not be disposed of as household waste.
Contact your retailer or local authorities for more information.
Remove any inserted batteries and dispose of them separately from the product.
---|---
| You as the end user are required by law (Battery Ordinance) to return all
used batteries/ rechargeable batteries. Disposing of them in the household
waste is prohibited. You may return your used batteries free of charge to
collection points in your municipality and anywhere where
batteries/rechargeable batteries are sold. By disposing of used devices and
batteries correctly, you contribute to the protection of the environment.
TECHNICAL SPECIFICATIONS
| Power supply: | 100-240 V AC, 50/60 Hz |
|---|---|
| Power consumption: | 110 W |
| IP classification: | IP20 |
| Protection class: | Class I |
| Power connection: | Mains input via P-Con (blue), mounting version Power supply |
cord with safety plug
Fuse:| 5 x 20 mm, T 2 A Fuse replaceable
Lamp type:| LED lamp
LED:| 1 x 80 W COB (chip-on-board) cold white (CW)
Flash rate:| 0 – 25 Hz
Equipment:| Gobo wheel with static gobos; Focus manual
Gobos:| Gobo wheel with static gobos, 1 gobo, 8 color gobos and open
DMX channels:| 7
DMX input:| 3-pin XLR (M) mounting version
DMX output:| 3-pin XLR (F) mounting version
Cooling:| Cooling fan
Control:
| Stand-alone; Master/slave function; Sound to light via Microphone; DMX;
QuickDMX via USB (optional); W-DMX by wireless solution via USB (optional);
CRMX by LumenRadio via USB (optional); Light´J; Light Captain; EASY SHOW 2;
EASY SHOW 3
Housing color:| Black – Article 51918595| White – Article 51918596
Display type:| OLED display
Dimensions:
| Width: 29.0 cm
Depth: 18.5 cm
Height: 31.5 cm
Weight:| 3.0 kg
| EUROLITE QuickDMX USB Wireless Transmitter/Receiver | No. 70064704 |
|---|---|
| EUROLITE TPC-10 Coupler, silver | No. 59006856 |
| EUROLITE TPC-10 Coupler, black | No. 59006858 |
| EUROLITE Safety Bond UNV-5 3x600mm up to 5kg silver | No. 58010372 |
| EUROLITE Safety Bond UNV-5S 3x600mm up to 5kg black | No. 58010373 |
| EUROLITE DMX cable XLR 3pin 3m black | No. 3022785H |
| PSSO DMX cable XLR 3pin 3m black Neutrik | No. 30227810 |
All information is subject to change without prior notice. © 03.05.2023
Eurolite is a brand of Steinigke Showtechnic GmbH
Andreas-Bauer-Str. 5
97297 Waldbüttelbrunn Germany
D00143444 Version 1.1 Publ. 03/05/2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>