EXSYS EX-60316 Power Over Ethernet PoE+ Gigabit Injector User Manual
- June 12, 2024
- EXSYS
Table of Contents
EX-60316 Power Over
Ethernet PoE+ Gigabit Injector
User Manual
EX-60316 Power Over Ethernet PoE+ Gigabit Injector
LAYOUT
DESCRIPTION & TECNICAL INFORMATION
The EN50155 compliant Gigabit Ethernet PoE Injector EX-60316 is designed for industrial applications e.g. in rail vehicles and railroad applications. It is compliant with the PoE+ standard IEEE 802.3at and provides a Gigabit PoE output. The EN50155 PoE injector uses M12 connectors to ensure tight, robust connections and reliable operation in the presence of environmental disturbances such as vibration and shock. The extended operating temperature range of -40°C to 80°C and rugged metal housing further contribute to operational reliability. The device does not turn on power until it detects a valid PoE signature from PoE devices downstream in the network. This provides protection against damage to non -PoE compatible devices that may be connected to the Ethernet cable. Power is supplied with a wide range voltage of +12 ~48V from an optional external power supply via the 4 -pin M12 connector. Included in delivery is a DIN- Rail kit (pre-assembled) and a wall mounting bracket.
| Compatibility: | Gigabit Ethernet 10/100/1000Base-TX |
|---|---|
| PoE: | IEEE 802.3af/at (PoE+) |
PoE (PSE): type 1 = 15.4W / type 2 = 34.2W
Operating System:| All operating systems
Connectors:| 2x M12-Jack 8-Pin / A-coded
1x M12-Jack 4-Pin / A-coded
Extent of Delivery:| EX-60316, DIN -Rail Kit, Wall Mounting Bracket, Manual
Certificates:|
CONNECTORS & LED’S
Network Port M12 (8-pin, A Coded):
Pin Assignment Ethernet/PoE
RJ45| M12| Signal| PoE| RJ45| M12| Signal|
PoE
1| 6| BI_DA+| | 5| 1| BI_DC-| VCC+
2| 4| BI_DA-| | 6| 8| BI_DB-|
3| 5| BI_DB+| | 7| 2| BI_DD+| VCC –
4| 7| BI_DC+| VCC+| 8| 3| BI_DD-| VCC –
Power Port M12 (4-pin, A Coded):
Power Connection
Pin| Signal| Pin| Signal
1| DC+| 3| DC-
2| GND| 4| GND
Status LEDs:
| LED Name | Color | LED Function |
|---|---|---|
| Power | Green | On: Powered |
Off: no power connection
PoE| Green| On: PoE activated
Off: no (PD) device connected
HARDWARE INSTALLATION
Please read the following installation instructions.
- Install the EX-60316 on a mounting rail using the DIN-Rail kit or on the wall using the wall mounting brackets.
The DIN-Rail Kit is pre-assembled with two screws on the rear side| To install the wall mount, the DINRail kit must be replaced by the mounting bracket
---|---
| - Connect the power connector (M12, 4 -pin) of the optionally available power supply to the DC-Input of the Injector and turn on the power supply.
- When the power is turned on, the PWR indicator lights up. If the indicator is not lit, check for proper connection to the power supply.
- Connect your router to the M12 input of the PoE injector.
- Now connect your PoE PD device to the PoE port.
- If all cables are connected correctly, the indicators light according to the port status of the LEDs (page 5).
CLEANING
To clean the device, please use only a dry, non -fibrous cloth and remove the
dirt with light pressure. In the area of the connections, please make sure
that no fibers of the cloth are left in the socket.
Attention! Never use a moist or wet cloth for cleaning!
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de
Sw itzerland:
EXSYS Vertriebs GmbH
Dübendorfstrasse 17
8602 Wangen
www.exsys.ch
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>