EXSYS EX-60310 Power Over Ethernet Gigabit Injector User Manual
- June 12, 2024
- EXSYS
Table of Contents
EX-60310
Manual
Vers. 1.0 / 03.10.22
LAYOUT
DESCRIPTION & TECNICAL INFORMATION
With the Gigabit Ethernet PoE Injector EX-60310 in a robust metal housing, end devices such as IP telephones, IP cameras, WLAN access points, etc. can be supplied with power via the network cable. It is compliant with the PoE+ standard IEEE 802.3at. The maximum power (PD) at the PoE port is 12.95W in type 1 and 25.5W in type 2, additionally LTPoE++ with up to 60W is possible. Power is supplied from an optional external power supply via the +12~48V terminal block. The EX-60310 ensures secure data transmission and excellent performance of up to 1000Mbps. Thanks to the rugged metal housing and the extended operating temperature range of -40°C to 80°C, it is suitable for a wide range of applications even in harsh environments. The scope of delivery includes a DIN-Rail kit (pre-assembled) and a wall mounting bracket.
| Compatibility: | Gigabit Ethernet 10/100/1000Base-T |
|---|---|
| PoE: | IEEE 802.3af/at/bt (PoE++) |
PoE (PSE): type 1 = 15.4W / type 2 = 34.2W / LTPoE++ = 60W
Operating System:| All operating systems
Connectors:| 2x RJ45-Port, 1x Terminal Block 12~48VDC
Extent of Delivery:| EX-60310, DIN -Rail Kit, Wall Mounting Bracket, Manual
Certificates:|
CONNECTORS & LED’S
RJ45 Port:
| Pin| Signal| PoE
---|---|---|---
| 1| BI_DA+| VCC+
2| BI_DA-| VCC+
3| BI_DB+| VCC –
4| BI_DC+| VCC+
5| BI_DC-| VCC+
6| BI_DB-| VCC –
7| BI_DD+| VCC –
8| BI_DD-| VCC –
Status LEDs:
| LED Name | Color | LED Function |
|---|---|---|
| Power | Green | On: Powered |
Off: no power connection
PoE| Green| On: PoE activated
Blinking: Power Device (PD) detected
Off: no (PD) device connected
12V to 48V T-Block:
ATTENTION!
Please pay attention to the correct polarity!
Never connect the power supply to the terminal block while it is switched on!
HARDWARE INSTALLATION
Please read the following installation instructions.
- Install the EX-60310 on a mounting rail using the DIN-Rail kit or on the wall using the wall mounting brackets.
The DIN-Rail Kit is pre-assembled with two screws on the rear side| To install the wall mount, the DIN Rail kit must be replaced by the mounting bracket
---|---
- Connect the power connector of the optionally available power supply to the terminal block and turn on the power supply.
- When the power is turned on, the PWR indicator lights up. If the indicator is not lit, check for proper connection to the power supply.
- Connect your router to the RJ45 input of the PoE injector.
- Now connect your PoE PD device to the PoE port.
- If all cables are connected correctly, the indicators light according to the port status of the LEDs (page 5).
CLEANING
To clean the device, please use only a dry, non -fibrous cloth and remove the dirt with light pressure. In the area of the connections, please make sure that no fibers of the cloth are left in the socket. Attention! Never use a moist or wet cloth for cleaning!
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de| Switzerland:
EXSYS Vertriebs GmbH
Dübendorfstrasse 17
8602 Wangen
www.exsys.ch
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>