saxby lighting 73535 Reeve 2 LED 40W Batten Instruction Manual
- June 13, 2024
- saxby lighting
Table of Contents
saxby lighting 73535 Reeve 2 LED 40W Batten Instruction Manual
Technical data
Supply
Voltage: 220-240 V~, 50 Hz
Bulb 40W LED Module (SMD), 6500K
Type: These products contain a light source of energy efficiency class E
Non-replaceable light source
Non-replaceable control gear
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
The power supply is Double Insulated and does not require connection to an Earth circuit.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.
This product is rated at IP65. IP65
This product is rated at IK08. IK08
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.
The LED module is protected by a shade. The shade cannot be replaced, if the shade becomes cracked or damaged, this light fitting must be discarded.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This power supply is Double Insulated and does not require connection to an Earth circuit Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Check the pack and make sure you have all the parts listed. Install in accordance with the IEE Wiring regulations and current Building Regulations. To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician. This light fitting should be connected to a circuit with a 30mA RCD fitted. If replacing an existing fitting, make a careful note of the connections. This light fitting should not be fitted to PIR circuits or short duration timed switches. The entire unit gets hot whilst on for a period of time. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distance between the junction box and the light fitting. Avoid
locating any cables in positions that would cause a hazard. Position cables
and outdoor rated junction boxes (not supplied) away from areas where they may
be at risk from being cut, trapped or damaged. We recommend that you use
H05RN-F specification cable (supplied) which is an outdoor grade, rubber
sheathed cable. The mains supply cable must have a minimum cross sectional
area of 1.0mm2 Cables must be protected using suitable conduit or plastic
trunking.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note that the switch is turned off before installation. Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product. The ceiling surface must be flat and smooth to ensure a good fit.
- Refer to the diagram below. Decide on the location of the product. Measure the distance between the mounting bracket location slots, mark the location of the fixing holes on the mounting surface.
- Drill holes and fit supplied wall plugs (suitable for masonry only – for other surfaces use appropriate fixings). Fix mounting brackets in place.
- Wire as detailed wiring diagram.
- Attach product to mounting brackets by pushing until securely held.
- Replace fuse or circuit breaker and switch on. Your light is now ready fo use.
Wiring
Having correctly identified the wiring from your existing light fitting,
connect to the approved IP67 (or higher rated) terminal block in the following
way (recommended terminal block Ref. 90131/90132)
Check that…
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
For further information, please visit https://www.lighting-info.co.uk/73536
V4 07/04/2022
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
UK Manufacturer: BH17 7BY