vtech DM1411 Digital Audio Monitor User Manual

: June 13, 2024
: vtech

User’s manual vtech DM1411 Digital Audio Monitor DM1411
Digital Audio Monitor
For more support informationhttps://vttqr.tv/?q=1VP204

DM1411 Digital Audio Monitor

Congratulations
on purchasing your new VTech product.
Before using this product, please read Important safety instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate your new VTech product. Please review this manual thoroughly to ensure proper installation and operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

What’s in the box

vtech DM1411 Digital Audio Monitor - box

Important safety instructions

The applied nameplate is located in the battery compartment of the baby and parent units.
When using your equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and injury, including the following:

Follow all warnings and instructions marked on the product.
Adult setup is required.
CAUTION: Do not install the soother at a height above 2 meters.
This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby.
Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
CAUTION: Use only the batteries provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The batteries cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of batteries into ﬁre or a hot oven, or mechanically crushing or cutting or the batteries can result in an explosion. Leaving the batteries in an extremely high temperature surrounding environment can result in an explosion or the leakage of ﬂammable liquid of gas. Batteries subjected to extremely low air pressure may result in an explosion or the leakage of ﬂammable liquid or gas. Dispose of used battery according to the information in The RBRC seal.
Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Use only adaptors and batteries listed below.
Power adapter information:
Output: 6V DC 400mA /5V DC 600mA VTECH TELECOMMUNICATIONS LTD.
Model: VT05UUS06040 / VT05EUS05060
Rechargeable battery information:
2.4V NiMH battery
YIYANG CORUN BATTERY CO LTD.
Model: NI-MHAAA400×2-FF/ NI-MHAAA750x2-FF
The power adapters are intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, underthe-table or cabinet outlet.
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Unplug the power cords before replacing batteries.
Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
Do not allow anything to rest on the power cords. Do noinstall this product where the cords may be walked on or crimped.
This product should be operated only from the type of pow source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 1
Do not overload wall outlets or use an extension cord.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.
Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than speciﬁed access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
You should test the sound reception every time you turn on the units or move one of the components.
Periodically examine all components for damage.
There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time.
Children should be supervised to ensure that they do not play with the product.
The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS
Cautions

Use and store the product at a temperature between 32 °F and 104 °F.
Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
Batteries should not be exposed to excessive heat such as bright sunshine or ﬁre.
Warning— Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9 m) away). Do not remove this tag.
Never place the soother inside the baby’s crib or playpen.
Never cover the soother or parent unit with anything such as a towel or a blanket.
Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients

Should keep wireless devices at least six inches from the pacemaker.
Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)
This VTech product complies with all standards regarding electromagnetic ﬁelds (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientiﬁc evidence available today.

Connect the baby monitor

Install the parent unit battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only.
NOTES
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.
vtech DM1411 Digital Audio Monitor - battery Replace the battery
To replace the battery, press down on the battery compartment cover and pull it out, then follow the steps above to install the battery.
Connect the baby monitor
NOTES

Use only the power adapters supplied with this product.
Make sure the baby monitor is not connected to a switch controlled electric outlet.
Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
Make sure the parent unit, the soother and the power adapter cords are out of reach of children.

Charge the battery
This portable soother has a built-in rechargeable battery for cordless usage.
To charge the battery, connect the soother with the adaptor provided to a power source.
NOTES

Make sure the soother and the adaptor are out of reach of children while charging.
The soother battery is fully charged after
12 hours of continuous charging.
The DC LPS power adapter is not provided in the package.
Position the soother
CAUTIONS
- This is not a toy. Do not let your baby play with the product.
- Keep the soother out of the reach of your baby. Never place or attach the soother inside the baby’s crib or playpen.

You can use the tail on the soother or the additional strap provided to hang and attach the soother to almost anywhere, e.g. stroller handle, doorknob, diaper bag straps, etc.
Using the tail
Use the tail to hook the soother on a desired object to keep it in position.

Charge the parent unit battery
When you have connected and turned on the soother and all the parent units, they will enter pairing mode automatically. It takes around 10 minutes for the pairing process to complete. When the parent unit and soother are successfully paired, the parent unit power LED is on steadily. The baby monitor is ready to use.
Notes

Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours.
It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.
The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.
The parent unit beeps twice every 10 minutes and the light ﬂashes in red when the battery is low.
Charge the parent unit battery without interruption for at least 30 minutes. To keep the battery charged, connect it to AC power when not in use.

**Before use

**

Note

This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such.

Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
**Caution**

For hearing protection, make sure the parent unit is more than 3 feet (1 meter) away from the baby unit. If you hear any high-pitched noise, move the parent unit further until the noise stops. You can also press on the parent unit to lower or mute the noise.
1. Make sure your soother and parent unit are on.
2. Speak towards the microphone of the soother You will hear the sound at the parent unit, and see the visual sound indicators light up.

Note

When the POWER/LINK LED light ﬂashes, move the parent unit closer to the soother (observe the minimum distance of 3 feet / 1 meter). You can also check if the soother is connected to a live power socket and switched on.

Tip

Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the soother.

Positioning the baby monitor
Caution

Keep the soother out of the reach of your baby. Never place or mount the soother inside the baby’s crib or playpen.
1. Place the soothers more than 3 feet (1 meter) away from your baby.
2. Place the parent unit more than 3 feet (1 meter) away from the soother to avoid screeching noise.

**Caution**

The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience high-pitched screeching noise from your baby monitor while positioning:
-Make sure your soothers and parent unit are more than 3 feet (1 meter) apart, OR
-Turn down the volume of your parent unit. Operating range
The operating range of the baby monitor is up to 1000 feet (300 meters) outdoors or 160 feet (50 meters) indoors. The actual operating range may vary depending on the environmental conditions and other interferences such as walls, doors and other obstructions.

**Using the baby monitor

**

Power on or off the soother

Switch to ON to turn on the soother.
Switch to OFF to turn off the soother.
Switch to on the soother only. to use the soothing functions

Power on or off the parent unit

Press and hold to turn on the parent unit. The POWER / LINK LED light turns on.
Press and hold again to turn off the parent unit. The POWER / LINK LED light turns off.

vtech DM1411 Digital Audio Monitor - soother

Adjust parent unit speaker volume
The speaker volume is preset to level 3, and the maximum volume is level 5. You can adjust it to your preferred volume level.

Press o on the parent unit to adjust the speaker volume.

Note

If you continue to press when the volume reaches the minimum or maximum setting, the parent unit will beep twice.

To mute the speaker volume:

Press▼ repeatedly until the volume reaches the minimum.

Notes

When the parent unit is in mute, the visual sound indicator will still indicate the sound detected from the soother.
To unmute, press ▲repeatedly until it reaches your desired volume.

vtech DM1411 Digital Audio Monitor - speaker volume

Parent unit alert tones

Low battery tone Out of range tone

Beeps twice every 10 minutes when the battery is low.
Beeps three times every 30 seconds when there is no link between the soother and parent unit, or when the parent unit is out of range from the soother.

CABLE MANAGEMENT

vtech DM1411 Digital Audio Monitor - CABLE MANAGEMENT

Soother overview

Lullaby
• Press to play or stop the lullaby.
vol-
• Press to decrease the speak volume.
Auto-off timer
• Press to turn on a 60-minute timer while playing lullaby or soothing sound. It will automatically stop the lullaby or soothing sound after playing for 60 minutes.
Skip
• Press to skip to the next lullaby or soothing sound.
Tail
• Hook the soother on an object.
Dimmable soft-glow night light
Soothing sound
• Press to play or stop the soothing sound.
vol +
• Press to increase the speaker volume.
Dimmable soft-glow night light
• Press to turn on the night light in dim light or bright light mode.
ON/ OFF/ power switch
• Slide to power on or off the soother, or use the soothing functions on the soother only.
DC jack for battery charging only
Slot for the additional strap
Speaker
Auto-off timer light indicator
• On when the auto-off timer feature is turned on.
• Off when the auto-off timer feature is turned off.
Battery status light indicator
• On when the battery is being charged.
• Flashes when the battery is low and needs charging.
• Off when the battery is not being charged; or the battery is fully charged.

Use the soother
Power on or off the soother

Slide the power switch on the right-hand side of the soother to on or off.

NOTE

Make sure the soother is on before using other features.

Play the lullaby
The soother has ﬁve lullabies for you to comfort your baby.

Brahms Lullaby
Rock a Bye Baby
Hush Little Baby
Minuet in G, Bach
Twinkle T winkle Little Star

Press to start playing lullabies.
Press to skip to the next lullaby.
While a lullaby is playing, press again to stop the lullaby.

NOTES

The soother will play the lullabies continuously unless you manually stop the lullabies or turn on the auto-off timer feature.
When a lullaby ends, the soother automatically skips to the next lullaby. After the soother plays the ﬁfth lullaby, it restarts playing from the ﬁrst lullaby again.

Play the soothing sound
The soother has ﬁve soothing sounds for you to comfort your baby.

White noise
Stream
Crickets
Birds
Heartbeat

Press to start playing soothing sounds.
Press to skip to the next soothing sound.
While a soothing sound is playing, press again to stop the soothing sound.

NOTES

The soother will play the soothing sounds continuously unless you manually stop the soothing sounds or turn on the auto-off timer feature.
The soother will repeat the same soothing sound again and again unless you skip to the other soothing sounds.

Adjust the speaker volume

Press vol- or vol+ at any time.

NOTES

The soother beeps to notify you when the speaker volume is already at the highest or lowest setting while adjusting.

Turn on or off the auto-off timer
While the soother is playing a lullaby or soothing sound, the auto-off timer feature helps you automatically stop the lullaby or soothing sound after playing for 60 minutes.

While a lullaby or soothing sound is playing, press to turn on the auto-off timer feature.
• The soother starts counting down 60 minutes. The auto-off timer light indicator on the left-hand side of the soother turns on.
After 60 minutes, the soother will automatically stop any lullaby or soothing sound. The cutoff timer feature and the corresponding light indicator will turn off.

NOTES

You can only turn on the auto-off timer feature when the soother is playing a lullaby or soothing sound.
The auto-off timer feature will not power off the soother after the 60-minute countdown.
You can press again to turn off the auto-off timer feature during the 60-minute countdown.
If you manually stop the lullaby or soothing sound while the auto-off timer is counting down, the auto-off timer will turn off.

Turn on or off the dimmable soft-glow night light When the soother is on, press repeatedly to choose from below night light options:

Turn on the night light in dim light mode, or
Turn on the night light in bright light mode, or
Turn off the night light.

NOTES

The night light will be automatically off after 15 minutes.

Parent unit overview

Visual sound indicators

The visual sound indicators can show the sound level detected by the soother or the volume level during speaker volume setting.
Sound level detected by the soother
•
One to three green lights indicate a moderate sound level detected by the soother.
•
Additional red lights indicate a higher sound level detected by the soother (e.g. baby crying loudly).
Speaker volume level
•
One to three green lights indicate Level 1 to Level 3 of the speaker volume setting.
•
Additional red lights indicate Level 4 to Level 5 of the speaker volume setting.

**POWER / LINK

** • Lights on steadily in green when the parent unit is on and linked to the soother.
• Flashes in green when there is no link between the soother and parent unit, or when the parent unit is out of range from the soother.

• Steady on in red when the parent unit is charging.
• Flashes in red when the battery is low.
▼(Volume down)
• Press to decrease the parent unit speaker volume.
Belt clip
(On/off)
• Press and hold to turn on or off the parent unit.
Power jack
▲(Volume up)
• Press to increase the parent unit speaker volume.
Speaker

Limited warranty

What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will replace at VTech’s option, without charge, a Materially Defective Product. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the replacement Products to you in working condition. You should expect the replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase (90 days on products purchased as Refurbished). This limited warranty also applies to the replacement Product for a period of either (a) 90 days from the date the replacement Product is shipped to you or (b) the time remaining on the original one-year warranty (90-day limited warranty on products that are purchased as Refurbished); whichever is longer.
*Refurbished products purchased from our online store carry a 90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:

Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion; or
Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized service representative of VTech; or
Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or
Product to the extent that the problem is caused by use with non-VTech accessories; or
Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or
Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or
Product returned without a valid proof of purchase (see item 2 below); or
Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 5959511. In Canada, go to www.vtechcanada.com or call 1 800-267-7377.
NOTE: Before calling for service, please review the user’s manual – a check of the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit.
What must you return with the Product to get warranty service?

Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difﬁculty; and
Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
Provide your name, complete and correct mailing address, and telephone number.

Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation. State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten warranty that the Product is ﬁt for ordinary use) are limited to one year from the date of purchase. Some states/ provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost proﬁts or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.

General product care

To keep this product working well and looking good, follow these guidelines:

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or ﬂuorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the parent unit and the soother in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the soother and parent unit are dry before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for some time, store the parent unit, the soother and the adapters in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about the baby monitor. If you cannot ﬁnd the answer to your question, visit our website at www.vtechphones.com, or contact 1 800-595-9511 for customer service.

Why doesn’t the POWER light on the soother turn on when I switch on the units?| Perhaps the soother is not connected to the power supply. Connect the soother to power supply. The soother turns on.
---|---
Why doesn’t the POWER / LINK light on the parent unit turn on when I switch
on the units?| Perhaps the battery of the parent unit is depleted and the parent unit is not connected to power supply. Connect the parent unit to power supply and charge the parent unit battery. The parent unit turns on and establishes connection with the soother.
Why does the baby monitor not respond
normally?| Try the following (in the order listed) for common cure:
1. Disconnect the power to the soothers and the parent unit.
2. Remove the battery from the parent unit.
3. Connect the soother to the power supply again. The soother turns on.
4. Connect the parent unit to the power supply again. The parent unit turns on.
5. Wait for the parent unit to synchronize with the soothers. Allow up to one minute for this to take place.
6. Press to adjust the speaker volume on the parent unit.
Why does the baby monitor produce a high-pitched noise?| The parent units and soother may be too close to each other.
• Move the parent unit away from the soothers until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent unit beep?| The parent unit beeps three times every 30 seconds when the soother is out of range. Move the parent units closer to the soother (but not less than 3 feet).
The parent unit may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for at least 30 minutes.
Why don’t I hear a sound/ Why can’t I hear my baby cry?| Make sure that both soother and parent unit are on. If you see the visual sound indicators light up, but there is no sound, then you may have muted the volume or set it to a lower level. Adjust the volume to a higher level.
If the visual sound indicators do not light up, and you cannot hear any sound, it is because the sound is too low for the soother to detect. This is normal. Place the soother at least 3 feet / 1 meter away from your baby.
Why does the light on the parent unit ﬂash?| The parent unit beeps twice every 10 minutes and the light ﬂashes in red when the battery is low. Connect the parent unit to the power supply and charge the battery for at least 30 minutes.
Why can’t I establish a connection?
Why is the connection lost every now and then?
Why are there sound interruptions?| The soother may be out of range. Move the parent units closer to the soother (but not less than 3 feet).
Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible.

FCC and IC regulations

FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian require ment:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Delve orpiment Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number onlysigniﬁes that the Industry Canada technical speciﬁcations were met.
This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.
RF radiation exposure statement
The device has been tested and complies with FCC and IC SAR limits.
This equipment complies with Industry Canada RSS-102 with respect to Canada’ s Health Code 6 for Exposure of Humans to RF Fields.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safety absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The Soother (baby unit) shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 20 cm (8 inches) or more.
For body worn operation, this parent unit has been tested and meets the FCC RF exposure guidelines when used with the accessories supplied or designed for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

California Energy Commission battery charging testing mode

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy- conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to soothers, the CEC battery charging testing mode is activated while it is powered off and charging.
The RBRC seal
The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.
The program provides a convenient alternative to placing used Ni-MH batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY ® for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road – Ste 555 Tigard, OR 97223, United States
Phone: 1 800-595-9511 in the U.S. or 1 800-267-7377 in Canada

Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.