saxby lighting 92542 Stratus Pro 50w Daylight Instruction Manual
- June 13, 2024
- saxby lighting
Table of Contents
Saxby lighting 92542 Stratus Pro 50w Daylight
Product Information
- Supply Voltage: 220-240V~, 50Hz
- Operational Voltage: 33-40V DC
- Bulb Type: 40W LED module (SMD), 4000K
- Energy efficiency class: E
- Light source: Non-replaceable
- Control gear: Replaceable by a professional
- Conformity: UKCA Directive requirements, EC Directive requirements
- Power supply: Double Insulated, does not require connection to an Earth circuit
- Panel light classification: Class III product, designed to be supplied via a transformer
- Disposal: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
- Check with your Local Authority or local store for recycling advice.
- Dimming: This product is not suitable for dimming
- IP Rating: IP40
- Accessories available: Suspension kit (81744) and Recess clip (91237)
Product Usage Instructions
- Cleaning: We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.
- Installation:
- If you are replacing an existing light fitting, correctly identify the wiring and pull the mains wire through the hole.
- Connect the mains wire to the connection block inside the LED driver as per the instructions.
- Ensure that any incoming earth cables are joined together and well-insulated with good-quality insulation tape to ensure earth continuity throughout your property. Note that this unit is double-insulated and must not be earthed.
- Commissioning:
- Ensure that the product is sitting properly on the suspended ceiling frame (refer to Fig. 4).
- Replace any other ceiling tiles if necessary.
- Replace the fuse or circuit breaker and switch it on.
- Your light is now ready for use.
For further information, please visit https://www.lighting-info.co.uk/92542
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This light fitting is double-insulated and does not require connection to an Earth circuit. Please read these instructions carefully before commencing any work This unit must be fitted by a competent and qualified electrician. Install in accordance with the IEE Wiring regulations and current Building Regulations. Check the pack and make sure you have all the parts listed. To prevent electrocution switch off the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. This light fitting should be connected to a fused circuit. If replacing an existing fitting, make a careful note of the connections. The part of the panel light at Safety Extra Low Voltage (33-40V DC ) via a transformer. Never connect the light fittings directly to the mains without using a transformer. This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped. Dimmable only when used in conjunction with suitable dimmable drivers. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the LED Driver and each light fitting. Ensure that there is adequate ventilation for the LED Driver. Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk of being cut, trapped, or damaged. The main supply cable must have a minimum cross-section area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking. These fittings are designed to be fitted into a suspended ceiling. Panels are rated as TPA according to Building Regulations B2.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the switch is turned off before installation.
- If there is a ceiling tile in position then ensure that it is removed (See Fig. 1).
- Wire the LED driver as shown below and connect the driver cable to the panel using a push & twist connector (See Fig. 2)
- Refit the cover on the LED driver.
- Place panel fitting into the ceiling.
- Ensure that the fitting is sitting properly on the T bar of the suspended ceiling and is not fouling any of the supporting bars (See Fig. 3).
Wiring
Having correctly identified the wiring from your existing light fitting, pull
the mains wire through the hole and connect to the connection block inside the
LED driver in the following way: This unit is double insulated and must not be
earthed. If there are any incoming earth cables, they must be joined together
and well-insulated with good-quality insulation tape. This is to ensure earth
continuity throughout your property.
Check that...
You have correctly identified the wires. The connections are tight. No loose
strands have been left out of the connection block.
Commissioning
Ensure that the product is sitting properly on the suspended ceiling frame
(see Fig. 4). Replace any other ceiling tiles. Replace the fuse or circuit
breaker and switch it on. Your light is now ready for use.
Technical data
Accessories available
Suspension kit – 81744 This kit will allow the panels to be suspended up to 1 meter from the ceiling. Two set suspensions (6 strings) are required for this panel light. Recess clip – 91237 Two set recess clips (6pcs) are required for recessed mount on alternative ceilings. For installation details please refer to the instruction manual of Recess Clip.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish. For your safety, always switch off
the power supply before cleaning. For further information, please visit
https://www.lighting-info.co.uk/92542V5 19/12/2022
UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1,
D-27442 Gnarrenburg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>