R3 Retractable Hose Reel Owner’s Manual

R3 Retractable Hose Reel

Product Information

• Product Name: Retracta R3 retractable hose reel
• Model Type: Air, Air/Water, Hot/Cold Water/Coolant, Horticultural Weed pesticide, Oil/Grease
• Quality: Hose Reels
• Manual Version: IMR3-issue 7

Page: 1

Introduction

Thank you for purchasing the Retracta R3 retractable hose reel. It is important to read and understand the safety information provided in this manual before using the product. This instruction manual will guide you through the operation of your new hose reel. Please retain this manual for future reference.

CAUTION: This manual contains cautions to prevent damage to the operator or the equipment. Pay attention to these warnings throughout the document.

General Warnings

• Do not exceed the maximum working pressure for this reel. Refer to the product specifications.
• Check equipment daily for wear or damage. Replace worn or damaged items immediately with genuine replacement parts.
• Check equipment daily for leaks. Repair or replace as required.
• Only use compatible fluids with this reel. Refer to compatible fluids in product specifications.
• Use equipment for intended use only.
• Operator should wear appropriate protection equipment to protect against personal injury.
• Do not attempt to stop leaks with your hand or body.
• Caution should be observed against burning due to hot water temperature when using hot water reels.
• Do not alter or modify equipment.
• Use reel in well-ventilated areas if toxic or flammable fluids are in use.
• Do not let go of the hose when rewinding.

INTRODUCTION

Thank you for purchasing the Retracta R3 retractable hose reel.
PLEASE READ THIS SAFETY INFORMATION CAREFULLY BEFORE USE.

Read and retain this instruction manual to assist you in the operation of your new product.
CAUTIONS’ are listed throughout this manual to advise of actions that may cause damage to you’re the operator or to the equipmen
CAUTION: The following general warnings should be observed when installing, operating or maintaining hose reel equipment. Further specific warnings pertaining to specific dangers may be found within this document

INSTALLATION INSTRUCTIONS

1. Use appropriate hardwear to secure and support the reel and bracket to desired location and weight of the fluids. (refer to back page for mounting bracket template)

2. Prevent the reel from swiveling in the overhead position (figure 2) by install locking bracket RP157 (supplied).

3. If spring recoil tension requires adjusting refer to
   “Add spring tension” for correct proceedure

4. Connect the fluid supply line to the side of the reel making sure to tighten appropriately.

5. It is recommended that an isolation valve is in-stalled before the reel inlet.

6. Connect a desired hose-end attachment and tighten appropriately. Thread sealant may be required.

7. Purge the air from the reel and check for any leaks or damage before initial use.

8. Before carrying out any maintenance, close isola-tion valve and remove all line pressure.

INCREASE SPRING TENSION
(ALL MODELS)

CAUTION: Before attempting any maintenance disconnect and turn off supply line, then release the line pressure.

1. Remove screws

2. Add 2 complete turns
   Note: 1 click on hub equals 90 deg

3. Replace screws

REMOVE / REPLACE TENSION SIDE PLATE

Before attempting any maintenance disconnect and turn off supply line, then release the line pressure

HOSE REPLACEMENT INSTRUCTIONS (ALL MODELS EXCEPT GREASE)

Before attempting any maintenance disconnect and turn off supply line, then release the line pressure.

HOSE REPLACEMENT INSTRUCTIONS (GREASE)

SWIVEL REPLACEMENT SWIVEL SEALS REPLACEMENT (AIR / AIR-WATER / COOLANT) (HORTICULTURAL / WEED PESTICIDE)

SWIVEL REPLACEMENT SWIVEL SEALS REPLACEMENT (OIL / HOT WATER)

SWIVEL REPLACEMENT (GREASE

RACR ADJUSTMENT CONTROL INSTRUCTIONS
(FOR MODELS FITTED WITH RACR)

1. Lift centre button to unlock then lift out plug
2. Pull hose out and latch when adjustment screw appears
3. Adjust speed as desired
   • (Clockwise for slower return)
   • (Counter clockwise for faster return)
4. Replace plug then press centre button to lock

TROUBLESHOOTING GUIDE

EXPLODED DIAGRAM

SWIVEL ASSEMBLY PART NUMBERS Air / Air-Water / Coolant

SPARE PARTS LIST

Accessories

DECLARATION OF CONFORMITY

MOUNTING DETAILS BU200 WALL MOUNT BRACKET

DIMENSIONS

BB200 BENCH MOUNT BRACKET

MOUNTING DETAILS

NOTE : Not to scale
This product should be disposed of according to all applicable local and national government environment regulations and guidelines.

• For Warranty Terms and Conditions see macnaught.com.au/macnaughtusa.com
• For a list of Australian Service Centres see macnaught.com.au

Macnaught Pty Limited

• Address: ABN 66 000 075 785 41 – 49 Henderson St Turrella, NSW, 2205
• Address: Sydney, Australia. Postal Address PO Box 90 Arncliffe NSW 2205 Sydney, Australia.
• T. +61 2 9567 0401
• F. +61 2 9597 7773
• W. www.macnaught.com.au

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>