schweigen CLUM12S Rangehood Installation Guide
- June 4, 2024
- schweigen
Table of Contents
- schweigen CLUM12S Rangehood
- Important Safety Information
- Before Installation
- Description
- Operation
- Cleaning & Maintenance
- Installation
- BBQ Installation
- Mounting Instructions – Outdoor/Alfresco
- Troubleshooting
- Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
schweigen CLUM12S Rangehood
Welcome
Thank you for purchasing your new Schweigen rangehood. To get the maximum
output from this unit, please read through this guide before use. The guide
contains important information on the use and maintenance of the unit, as well
as important safety notes. This will ensure your personal safety and the
lasting value of your rangehood. We trust that you will enjoy your new
Schweigen rangehood.
Please always retain your proof of purchase to aid in any warranty queries.
If you are unable to locate your warranty card, one is available to
download from our website www.schweigen.com.au.
This appliance and its packaging are produced by processes that minimize waste
and respect the environment. Please help us to continue this effort to protect
the environment by using the appliance efficiently and dispose of the
packaging in a responsible manner.
Your State Regulatory Authority
Different Australian states have varying legislative requirements for the
installation of rangehood ducting. Some will insist on ducting being vented
externally (i.e. not in to the ceiling cavity); others will not. It is
imperative that you check with your state building authority and/or private
certifier to confirm their position.
Important Safety Information
WARNING
Please read this section thoroughly before attempting to operate the
appliance. Inspect your product upon receipt. Any damage or defects MUST be
reported within 48 hours, or no claim will be recognised.
DO NOT INSTALL THIS APPLIANCE IF YOU FIND IT DAMAGED.
If this product is installed damaged, neither the supplier, nor the retailer,
will be responsible for the costs associated with the repair, replacement,
removal or re-installation of the appliances.
- To be installed in an undercover alfresco area only.
- If the unit is not adequately covered or sheltered from the outside elements the warranty will be null and void.
- There shall be adequate ventilation in the room when the rangehood is used at the same time as appliances burning gas or other fuels.
- There is a fire risk if cleaning is not carried out in accordance with the instructions.
- Do not flambé under the rangehood. This will damage the rangehood and will not be covered by warranty.
- Do not ignite burners that give off intense, uncontrolled flames beneath the rangehood.
- Make sure that no flames emerge from the sides of pans.
- Do not leave packaging materials (bags, corner brackets, etc.) within reach of children.
- This appliance is not intended for use by person/s (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person has been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance, it is not a toy.
- Exhaust air must not be discharged into an existing flue that is used for exhausting fumes from appliances burning gas or other fuels.
- Air exhaust must be installed in accordance with local laws. Regulations concerning the discharge of air have to be fulfilled.
- Accessible parts may become hot when used with cooking appliances.
- Before performing any cleaning or maintenance operation, disconnect the rangehood from the mains using the respective mains or sector switch or by unplugging it.
- Do not use the rangehood without the grease filters.
- Keep the grease filters clean and respect the recommended cleaning frequencies.
- Turn the rangehood motor on before starting to cook.
- Turn the rangehood motor off about 10-15 minutes after you finish cooking.
- It is forbidden to use the rangehood as an aspirator.
- Never cook foodstuff directly over the flame or have the gas burners on under the rangehood without using cookware.
Before Installation
- We recommend this appliance be installed or repaired by an experienced Home Appliances technician.
- Please see our website www.schweigen.com.au for experienced installers.
- It is dangerous to modify any part of this appliance. Modification of any kind, will immediately void the warranty.
- The manufacturer declines all responsibility in case of failure to adopt proper safety measures.
- Ensure that the location in which this appliance is installed, has good and permanent ventilation.
- Please consult local laws and regulations and install in accordance.
- Use an electrical connector with earth that is correct for your location.
- Check that the voltage in your area corresponds to the appliance as indicated on the rating label.
- This appliance must be connected to an electricity supply with a ground connection.
- Check that the installation and electrical connections are made by a qualified technician and that the indicated instructions and local regulations in force are met, using materials that are compliant with the applicable legislation.
- The company will not be responsible for installations executed by non-qualified staff and installations that fail to heed the applicable legislation on electrical safety (with regard to both modes and materials).
- The electrical technical data can be found inside the rangehood, after removing the grease filters.
- The flexible power cable supplied is already connected internally and emerges from the rangehood near the air outlet tube.
- Before installing the electrical connections, you should:
- Verify that the indicated electrical data coincide with the voltage values and frequency of the electrical circuit in the house where the rangehood is to be installed;
- Check that the premises has electrical protection against short circuits and electrocution, pursuant to the applicable legislation;
- Always switch off the current using the double-pole switch before maintenance and turn the power on again for normal use only when the operation has been completed.
Product Use
This product is designed for household use and should not be used for
commercial applications. After use, always ensure that all controls are in the
“OFF” position. When frying with a gas flame, take particular care not to
allow the oil or grease in the pan to catch fire. (Flambé)
Electrical Cord
Ensure the supply cord is not exposed to heat, chemicals or sharp objects. If
the supply cord is damaged, it must be replaced by the manufacturer.
Description
Rangehood
- Socket lead for Isodrive® motor
- Main Power Cord
- 2x 200mm outlets
- Body
- Lights
- Baffles
- Remote Control
NOTE:
Filter and light quantity may vary from model to model. Cutout Size
Use this as a guide only when designing your cabinet. We advise you to take
the rangehood to your cabinet maker so they can tailor the cabinet to fit
correctly.
Note:
Please make sure that all plastic protection on the rangehood and filters are
removed before use.
Operation
TOUCH BUTTON CONTROL PANEL
REMOTE CONTROL
As well as the touch buttons, this rangehood comes with a remote control to
operate the rangehood.
- Use this button for turning on and off the rangehood.
- Changes the speed of the motor (minimum level is 1, maximum is 5.)
- Automatically changes the speed to maximum or minimum speed.
- Turns the lights on or off.
- 10 minute timer.
USING THE ON/OFF BUTTON
To turn on the rangehood press the on/off button. Press the on/off button a
second time to activate the 10 min auto-shut off timer. Press the on/off
button a third time to turn the rangehood off.
SPEED CONTROL
This rangehood is equipped with a 5 speed touch control.
Speed control usage suggestions:
- Low speed for simmering.
- Medium speed for light cooking.
- High speed for heavy frying/cooking.
Cleaning & Maintenance
Warning
Always switch off and disconnect power before cleaning.
Cleaning the Interior
Clean the interior of the rangehood with a damp cloth and a neutral detergent
or denatured alcohol.
NOTE:
Do not use denatured alcohol on the exterior of the rangehood. Do not clean
the electric parts or the motor with liquids or solvents
Cleaning the Exterior
We recommended using a soft cloth, water and a liquid soap, rinsing it well
and then drying it thoroughly. For better results, you can use high quality
cleaning and protection products (e.g. Steel Kleen) to clean your rangehood.
- The recommended detergent is a solution of water and a neutral liquid soap.
- It is very important for the liquid soap to not contain granules that could scratch the surface.
- First apply the solution to a soft cloth and then rub the cloth over the rangehood. It is important to follow the direction of the stained surface with the cloth (refer to figure on left).
- Do not pour any liquid directly on to the rangehood.
- The cloth must have no buttons, zips or fasteners that could scratch the surface.
- It is strictly forbidden to use chemical solvents, aggressive, grainy or abrasive products, naphtha, alcohol or similar products that could damage the surface of the rangehood.
- The manufacturer will not be held responsible for functional or aesthetic damage caused by cleaning with products which are not suitable or using inadequate cleaning methods.
Baffles
For this appliance to function effectively, regular maintenance is a must.
- The function of the baffle is to collect the grease particles given off during cooking.
- Clogged heavy oil deposits restrict airflow and may cause the motor to overheat and become a fire hazard.
- Baffles should be cleaned every 3-6 weeks or after 40 hours of use.
- For induction cooktop, please aim to clean them at least every 10 days, depending on use.
- The bafles can be washed by hand or in the dishwasher.
- Washing by hand – Immerse the filter in hot water and a suitable detergent and when clean, rinse with plenty of hot water.
- Dishwasher – Put the filter in the dishwasher and select a short program at low temperature. NOTE: The colour of the metal mesh filters may change after several washes. This is normal and it is not necessary to change the filters.
Please ensure the baffles are completely dry before placing them back in
position and operating the rangehood.
Endure the baffles are cool before removing, to ensure no oil is spilt. To
remove, push away from you until the near edge clears the slot. Then carefully
pull down and back to remove. To replace, perform the same operation but in
reverse.
Warning
- If the baffles are very dirty, the motor will extract only a small quantity of air, which reduces its efficiency;
- The grease deposits that build up on the baffles are highly flammable and COULD EASILY CATCH FIRE.
- The manufacturer is exonerated from all responsibility in the event of fire due to poor maintenance of the grease filters.
Replacing the Light
Danger
Always switch off and disconnect the power cord before replacing any light
bulbs. Failure to do so may cause serious injury. Please be aware that the
light bulb will retain heat for a short period of time after being switched
off.
-
Step 1 Remove the filters from the rangehood.
-
Step 2 Gently turn light bulb clockwise, pull the light bulb down and remove it from the light holder.
-
Step 3 Insert a new light bulb by lining up the pins of the light bulb with the larger holes inside the light holder. Once the pins are in place, turn anti-clockwise to secure the light bulb.
Installation
Rangehood Size vs Cooktop Size
In addition to the size, the height of the rangehood above the cooktop is
important to obtain the best performance.
- INADEQUATE Rangehood smaller than cooking zone
- ADEQUATE Rangehood same size as cooking zone
- OPTIMAL Rangehood larger than cooking zone
BBQ Installation
When installing the rangehood over a BBQ , please be aware that the lid will
obstruct the range hoods effectiveness to extract smoke, steam and odours.
Where possible, remove the lid of the BBQ unit when in use, so as to allow for
effective rangehood extraction. Alternatively, install the rangehood on an
extension, to move the rangehood further out.
Mounting Instructions – Outdoor/Alfresco
When installing in an outdoor kitchen or alfresco area, the rangehood MUST
NOT be installed where it is directly exposed to the elements .
It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the
cooktop. This will greatly improve its performance.
Minimum legal height from the BBQ surface to the underside face of the
rangehood:
- 1200mm
Any installation above 1200mm will compromise the extraction performance.
Measurements are from the top of the trivets to the lowest
part of the rangehood, including the button controls.
IMPORTANT:
If the user decides to install the rangehood at a distance of less than
minimum height above the cooking surface, Schweigen declines responsibility
for damages suffered by the rangehood due to excess heat or damage to objects,
people and others caused directly or indirectly by a malfunction, breakage or
fire.
- In addition to the information in this manual, please check all relevant state requirements for minimum–maximum heights, as well as regulations regarding the expelling of air. Schweigen is not liable if your rangehood is not installed in accordance with these legal requirements.
Mounting Points for Body
The diagrams below are a guide for all mounting points.
SIDE VIEW FRONT VIEW
WARNING
Please remove filters before installation. Failure to do so may damage the
clips.
DANGER
Always switch off and disconnect the power supply before installing the
rangehood. Failure to do so may cause serious injury.
Installation Example
- Step 1
Insert support frame into cabinet. The support will only be needed in certain
circumstances.
NOTE:
The support frame is not included. The requirement of a support frame is
dependent on the type and location of installation. Please contact your
installer for more information.
- Step 2
Secure support frame to inside of cabinet.
- Step 3
Secure the undermount into cavity using screws. All screws are installed
internally into a support frame.
IMPORTANT
Please ensure all plastic protection on the rangehood and filters is removed
before use.
Ducting
Please DO NOT crush or kink the ducting.
-
Crushed or kinked ducting creates sharp corners that creates turbulence. This reduces the size and efficiency of the ducting, lowers extraction and may cause excessive noise.
-
Sweeping curves and taut ducting reduces resistance and turbulence. The airflow and extraction will be more efficient and stronger.
Isodrive® Motor Setup
Note
Please refer to the Isodrive® motor installation guide for more details on
ducting and Isodrive® motor installation.
Single Isodrive® Motor Installation
-
Isodrive® Motor
-
Roof Seal Kit (Dektite) (Not supplied)*
-
Support Straps (Not supplied)*
-
Isodrive® Motor Power Lead (Plug)
-
Rangehood to Isodrive® Motor Lead (Socket)
-
Multi-fit Y-Joint, cut to 250 x 200 x 200mm
-
Mains power
-
Ducting must be pulled taut.
DO NOT crush or kink the ducting. -
Connect ducting to the outlet on rangehood using ring clamp.
Please DO NOT rip the ducting.
NOTE
The Isodrive® motor system does not include the roof seal kit, cable ties or
the support straps.
- The general power outlet for the rangehood should be located in an easy to access area.
DANGER
All electrical wiring from the motor to the rangehood should be kept inside
the roof space.
Twin Isodrive® Motor Installation
-
Isodrive® Motors
-
Roof Seal Kit (Dektite) (Not supplied)*
-
Support Straps (Not supplied)*
-
Attach Duct to Bell-Mouth Adaptor using ring clamp. Please DO NOT rip the ducting.
-
Isodrive® Motor Power Lead (Plug)
-
Rangehood to Isodrive® Motor Lead (Socket)
-
Mains power
-
Ducting must be pulled taut.
DO NOT crush or kink the ducting. -
Connect ducting to the outlet on rangehood using ring clamp.
Please DO NOT rip the ducting
NOTE
The Isodrive® motor system does not include the roof seal kit, cable ties
or the support straps.
- The general power outlet for the rangehood should be located in an easy to access area.
DANGER
All electrical wiring from the motor to the rangehood should be kept inside
the roof space..
Optional Wall Mounted Motor Installation
The Isodrive motor can optionally be installed mounted to a wall if a roof
mount is not possible. The construction of a bulkhead is also recommended. The
position of the motor can be to an external wall as shown above, or to the
same external wall as the rangehood is mounted, as shown below. For all wall
installation options, please refer to the Isodrive® Motor manual. Avoid sharp
bends and kinked ducting as this will affect extraction
performance.
Top
view for wall mounted installations on the same wall as the rangehood.
Troubleshooting
Before you contact the technical service department, make sure that the product is plugged in and power is supplied.
- Do not take any action that will damage the product.
IMPORTANT
Never attempt to repair this appliance by yourself. Always refer to a
qualified Service Technician. Service
Lodging an Online Service Request
In the event that the failure is not due to the faults mentioned in the
Troubleshooting section, you can lodge an online Service Request. To lodge an
online Service Request, visit our website www.schweigen. com.au/service-and-
warranty and click on
the link and complete the service request form.
A service request will require the following information:
- The purchase date
- The rangehood model and motor type (e.g. Isodrive® 650)
- The serial number or batch number (this number is on a sticker inside the rangehood).
- A copy of the purchase receipt (without a receipt your service request cannot be processed).
Alternatively, you can call Customer Service:
Australia : 1300 881 693
New Zealand : 0800 200 510
Faulty Installation
It is not the responsibility of Schweigen to rectify any incorrect installations. A service call out fee will be charged for any Schweigen technician that attends a call, whereby it is established that the fault is due to an incorrect installation or non-manufacturing fault. Should the appliance be installed in such a way that the service agent is unable to gain access to the appliance, the person/s who own the premises or the property where the appliance resides — will be responsible to provide access to the appliance at their expense.
Specifications
Dimensions
Technical Specifications
Model | CLUM12S |
---|---|
Feeding Voltage | 220–240V 50Hz |
Lamp Power — LED (W) | 2 x 3W |
Disclaimer
Under our policy of continuous product development, product specifications may
change without notice. Prospective purchasers should therefore check with the
retailer to ensure this publication correctly describes the products being
offered for sale. All information supplied is to be used for general reference
purposes only and is on the understanding that Schweigen Home Appliances will
not be liable for any loss, liability or damage of whatever kind arising as a
result of any reliance upon such information. All pictures used in the guide
are for illustrative purposes only. Although our information and marketing
states the term ‘Silent’ for certain models, the following applies to various
models that are sold with certain Isodrive® Systems and baffle filters. When a
model with the larger motored Isodrive® System is operated at the higher
speed/s air movement may be heard. For example, while operating on speed 4 & 5
(For 5 speed models) the rangehood may be audible due to the large amount of
air movement moving through the filter.
- Please make sure that the rangehood and motor have been installed as per the corresponding instruction guides in order for optimal performance (the Isodrive® Motor Manual can be found with the Isodrive® Motor, or online at schweigen.com.au).
Schweigen Home Appliances has presented this information in good faith to all
their retailers and distributors to convey before any/all purchase/s.
Information is supplied upon the condition that the person/s receiving the
information will make their own determination as to its suitability for their
purpose/s prior to use. In no event will Schweigen Home Appliances be
responsible for damages of any nature whatsoever resulting from the use of, or
reliance upon, information from their website or the products to which the
information refers.
DISPOSAL OF OLD APPLIANCES
Electronic waste (or e-waste) including kitchen appliances are banned from
direct disposal to landfill. E-waste contains hazardous materials, which can
harm the environment and human health. Valuable materials contained in e-waste
are lost when appliances, computers and other household electrical goods are
sent to landfill.
Recycle your e-waste to:
- reduce landfill
- protect the air and waterways from harmful materials
- minimize consumption of raw materials to produce electronic products
- educe greenhouse gases created in the production of new materials.
Kitchen appliances including Rangehoods and Ovens can only be disposed at approved recycling centres. Visit www.recyclingnearyou.com.au/whitegoods for more information, or contact your local council or the store you purchased this appliance, for a list of approved recyclers.
References
- SCHWEIGEN Silent Rangehoods
- Home - Parex
- Recycling Whitegoods - Planet Ark Recycling Near You
- SCHWEIGEN Silent Rangehoods
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>