schweigen IN KLS-9GLASSBLKS Undermounted Rangehoods Instruction Manual

IN KLS-9GLASSBLKS Undermounted Rangehoods
Installation / Operation / Maintenance
KLS-9GLASS
Instruction Manual

INSPIRING INNOVATIVE
INTELLIGENT
Under our policy of continuous product development, product specifications may change without notice. Please refer to the online version of the manual for the latest updates and specifications.

WELCOME

Thank you for purchasing this Schweigen IN appliance.
To achieve the optimal performance from your appliance, and to avoid the risk of accident or damage, it is essential to read this manual before installation and first-time use.
This guide contains important information on the use and maintenance of the appliance, as well as important safety notes.
Your appliance has been thoroughly checked for safety and functionality before being packaged and leaving the manufacturer.
Please keep this instruction manual in a safe place so you can refer to it at any time.
IMPORTANT!
The appliance should only be operated when you have read and understood this manual thoroughly.
The appliance can be only used for the purpose for which it was designed. Any other use is deemed improper and can be dangerous.
Installation and maintenance of electrical appliances must only be carried out by qualified and authorized professionals familiar with Australian Appliance Industry regulations.
Upon collection or delivery of your appliance, any damage or defects must be reported within 48 hours to your retailer or Schweigen Customer Service, in order to recognize any claim.
The manufacturer reserves the right to introduce product improvements, which do not affect the operation of the appliance.
YOUR STATE REGULATORY AUTHORITY
Different Australian states have varying legislative requirements for the installation of rangehood ducting. Some will insist on ducting being vented externally (i.e. not into the ceiling cavity); others will not. It is imperative that you check with your state building authority and/or private certifier to confirm their position.

IMPORTANT SAFETY INFORMATION

Please read the instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual for future use or for subsequent owners.
Check the appliance for damage after unpacking it. Do not connect or install the appliance if it has been damaged in transport.
Any damage must be reported within 48 hours.
There must be adequate ventilation in the room when the rangehood is used at the same time as appliances burning gas or other fuels.
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
Air exhaust systems must be installed in accordance with local and federal laws.
There is a fire risk if regular cleaning is not carried out in conjunction with the instructions.
Do not flambé (ignite food while cooking) under the range hood. This will damage the rangehood and will void the warranty.
Do not ignite burners that give off intense uncontrolled flames beneath the range hood.
Flames beneath the pan must be contained at all times and cannot exceed the width of the pan in use.
Do not leave any packaging material (bags, corner brackets, etc.) within reach of children.
This appliance is not intended for use by person/s (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person is given supervision or instruction concerning the safe usage of the appliance by the person/s responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance, it is not a toy.
Accessible parts may become hot when used with cooking appliances.
Before performing any cleaning or maintenance, disconnect the rangehood from the mains’ power, using the respective mains or sector switch, or unplugging it.
Do not use the rangehood without the grease filters.
Keep the grease filters clean and respect the recommended cleaning frequencies.
It is forbidden to use the rangehood as an aspirator.
BEFORE INSTALLATION
We recommend this appliance be installed or repaired by an experienced Home Appliances technician.
Please see our website www.schweigen.com.au for a list of experienced installers.
It is dangerous to modify any part of this appliance.
Modification of any kind will immediately void the warranty.
The manufacturer declines all responsibility in case of failure to adopt proper safety measures.
Ensure the location in which this appliance is installed, has good and permanent ventilation.
Please consult local laws and regulations and install them in accordance.
Please use an earthed electrical connector that coincides with relevant local laws and regulations.
Check that the power voltage in your area corresponds to the appliance voltage indicated on the rating label.
This appliance must be connected to an electrical supply that has a grounded connection.
Check that the indicated instructions and local regulations are met and carried out by a qualified technician, using materials that are compliant with the applicable legislation.
Schweigen will not be responsible for any installations executed by non- qualified technicians that fail to heed the applicable legislation on electrical safety.
The electrical technical data can be found inside the rangehood, after removing the grease filters.
The power cables supplied are already connected internally and emerge from the rangehood near the air outlet.
Before installing the electrical connections, you should:
Verify that the indicated electrical data coincides with the voltage values and frequency of the electrical circuit in the house where the range hood is to be installed.
Check that the premises have electrical protection against short circuits and electrocution.
Before commencing maintenance the current must be turned off using the double- pole switch (mains power switch). The power can only be turned on for normal use, once the operation has been completed.
Ensure the supply cord is not exposed to heat, chemicals, or sharp objects. If the supply cord is damaged, it must be replaced by the manufacturer, service agent, or a similarly qualified person in order to avoid a hazard.
PRODUCT USE
This product is designed for household use and should not be used for commercial applications.
After use, always ensure that all controls are in the “OFF” position.
When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire. (Flambé)

MAINTENANCE AND SERVICE

The rangehood surface should be cleaned with a soft cloth and non-corrosive detergent. Do not leave the rangehood wet after cleaning or use, please keep the rangehood dry.
Important: Never attempt to repair this appliance by yourself. Always refer to a qualified Service Technician.
Always switch off the electricity and unplug the connection before conducting maintenance or cleaning.
ELECTRICAL CORD
Ensure the supply cord is not exposed to heat, chemicals, or sharp objects. If the supply cord is damaged, it must be replaced by the manufacturer, service agent, or a similarly qualified person in order to avoid a hazard.

DESCRIPTION

For models KLS-9GLASS and KLS-9GLASSBLKS

1. Socket lead to Isodrive® motor
2. Main power cord
3. Single 200mm Outlet
4. Computer board*
5. Reducer
6. Filter
7. Cabinet door protection strip
8. Light
9. Rangehood mounting brackets
10. Instruction and screws pack

*IMPORTANT: The electronics MUST be accessible for servicing once installed, failure to do so, will result in any charges involved with accessing the part (removal of abinetry, etc.) being forwarded to the customer.

OPERATION

For models KLS-9GLASS and KLS-9GLASSBLKS
The range hood has a 4-speed electronic keypad.
Speed control usage suggestions:

• Low speed for simmering.
• Medium speed for light cooking.
• High speeds for heavy frying or heavy cooking.

Electrical Touch Keypad
To obtain the best performance, switch the rangehood on a few minutes prior to cooking and leave running for at least 10 minutes after you have finished.
The buttons have the following functions:
A.- Light switch: Press this switch to turn the lights on and off.
B .- ON / OFF / button – speed one: This button turns the rangehood on and off. The rangehood starts to operate at speed one.
C. D. E.- Speeds 2, 3, and 4, respectively.
F.- Timer: When the timer mode is in operation, the timer button light will remain on. When this button is pressed, the rangehood will continue to operate for 10-15 minutes at the required speed, and then switch off automatically.
This range hood has a device that lets you know when the grease filters must be cleaned. When the timer button (F) flashes, this means the filters must be washed (usually after 40 hours of operation).
When the filters have been washed and re-mounted, hold the timer button (F) down for a few seconds to reset it and return the counter down to zero.

CLEANING AND MAINTENANCE

WARNING
Always switch off and disconnect power to the range hood before cleaning. The manufacturer is exonerated from all responsibility in the event of a fire due to poor maintenance of the filters and rangehood.
Cleaning and user maintenance shall not be made by children without supervision.
FILTERS

• For your appliance to function effectively, regular maintenance is a must.
• The function of the filter is to absorb the grease particles emitted during cooking.
• Blocked filters and heavy oil deposits restrict airflow and may cause the motor to overheat and become a fire hazard.
• Filters should be cleaned every 3-6 weeks or after 40 hours of use.
• Disconnect the electrical connection before any maintenance or cleaning processes are carried out.
• In ceiling-mounted range hoods, the doors or glass must be opened before accessing the filters.
• To remove the filter, (open the glass panel, figure 1, if required) press ‘Catch A’ towards the rear of the rangehood (removing the pins from the front guide), ease down slightly and remove. To replace, perform the same operation but in reverse, see figure 2.
• For an induction cooktop, please aim to clean the filters at least every 10 days, depending on the frequency of use.
• The filters can be washed by hand or in the dishwasher

Washing by hand – Immerse the filters in hot water and a suitable detergent, when clean, rinse with plenty of hot water.
Dishwasher – Put the filter in the dishwasher and select a short program at a low temperature.
NOTE: The color of the metal mesh filters may change after several washes. This is normal and it is not necessary to replace the filters.

SURFACES
The surface of the range hood can be cleaned with warm soapy water and a soft sponge/cloth.

• Never use abrasive detergents, scouring pads, steel wool, or solvents on ANY part of this appliance.
• Rinse with clean water and ensure that the appliance is completely dry after cleaning.
• Always make sure the appliance is completely dry after cleaning and never leave it wet, this may cause irreparable damage.

It is important to follow the direction of the surface grain with the cloth (refer to figure below).

Do not pour any liquid directly onto the rangehood, apply to a soft cloth first.
The cloth must have no buttons, zips, or fasteners that can scratch the surface.
It is strictly forbidden to use chemical solvents, aggressive, grainy, or abrasive products, naphtha, alcohol, or similar products that could damage the surface of the range hood.
The manufacturer will not be held responsible for functional or aesthetic damage caused by using inadequate cleaning methods.
Cleaning the Interior
Clean the interior of the range hood with a damp cloth and a neutral detergent or denatured alcohol.
Replacing the Lights
Never attempt to replace the lights by yourself, always get a qualified service technician.
WARNING
Do not use denatured alcohol on the exterior of the rangehood. Do not clean the electric parts or the motor with liquids or solvents.

INSTALLATION

RANGEHOOD SIZE VS COOKTOP SIZE
In addition to the size, the height of the rangehood above the cooktop is important to obtain the best performance.

INADEQUATE
Rangehood smaller than cooking zone| ADEQUATE
Rangehood same size as the cooking zone| OPTIMAL
Rangehood larger than cooking zone

OVERHEAD CABINET RANGEHOOD INSTALLATION POSITION
It is important to consider the benchtop and overhead cabinetry depth before installing the rangehood.
The information below is to be used as a guide only, drawings are not to scale and do not account for all circumstances.
The cooktop is centrally installed on the benchtop in the diagrams below.
When the overhead cabinetry is constructed and installed deeper than standard, ensure the rangehood is installed as close to the front as possible.
This will increase the rangehood extraction results as there is greater coverage of the cooktop surface area.

DANGER
Always switch off and disconnect mains’ power before installing the rangehood.
Failure to do so may cause serious injury.
MOUNTING LAWS AND REGULATIONS
It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the cooktop. This will greatly improve its performance.
Minimum height from the hob top surface to the underside face of the rangehood:

• 650mm electric cooktop
• 650mm gas cooktop

Any installation above 800mm will compromise the extraction performance.
Note: If the instructions for the gas cooktop specify a greater distance, this must be taken into account.
RECOMMENDED INSTALLATION HEIGHT FOR INDUCTION COOKTOP
To help avoid condensation, particularly to cooking with an induction cooktop, Schweigen recommends a minimum height of 700mm. Refer to page 19 for further information.

*IMPORTANT: If the user decides to install the rangehood at a distance of less than the minimum height above the cooking surface, Schweigen declines responsibility for damages suffered by the rangehood due to excess heat or damage to objects, people and others caused directly or indirectly by a malfunction, breakage or fire.
Measurements are from the top of the trivets to the lowest part of the range hood, including the button controls.
IMPORTANT
Please check all State and Federal Laws in relation to the minimum-maximum heights, and regulations concerning the expelling of air, and install your rangehood in accordance with local laws and regulations.
IMPORTANT
Please read the installation guide thoroughly prior to installation. These models have a different method of installation compared to standard undermounts.
Step 1
Fix the rangehood mounting supports (A) to the sides of the cabinet (B).
NOTE: The brackets need to be leveled and secured, in order to hold the entire weight of the under-mount.
Step 2
Slide the under-mount in from the front of the cabinetry, onto the rangehood mounting supports (A).
Line up the undermount bracket (C) with the holes on bracket (A). 

Step 3
Fit the undermount in place, using the installation screws provided (E).
Protecting the Cabinet Door — Optional
A reversible “L” shaped profile is provided for optional cabinet door (D) protection.

Step 4
Only install the reducer if you are connecting the rangehood to the Isodrive ® 650 motors. DO NOT install the reducer for any other motor system.

Step 5
Once the rangehood is fitted into the cabinetry, connect the male and female power connections to the corresponding connections. Male to main power, female to Isodrive ®
motor. The ducting will attach to the outlet on the rangehood and the Isodrive ® motor.
NOTE: The electronics need to be accessible after installation, in case a service is required.
IMPORTANT
Please ensure all plastic protection on the range hood and filters are removed before use.

Please DO NOT crush or kink the ducting.

1. Crushed or kinked ducting creates sharp corners that create turbulence. This reduces the size and efficiency of the ducting, lowers extraction, and may cause excessive noise.

2. Sweeping curves and taut ducting reduce resistance and turbulence. The airflow and extraction will be more efficient and stronger.

SYSTEM OVERVIEW 

1. Isodrive ® Motor
2. Roof Seal Kit (Dektite) (Not Supplied)*
3. Support Straps (Not Supplied)*
4. Attach Duct to Bell-Mouth Adaptor using ring clamp. Please DO NOT rip the ducting.
5. Isodrive ® Motor Power Lead (Plug)
6. Rangehood to Isodrive ® Motor Lead (Socket)
7. Main Power Lead (Plug, 10 Amp)
8. Ducting must be pulled taut. DO NOT crush or kink the ducting.
9. Connect ducting to the outlet on rangehood using ring clamp. Please DO NOT rip the ducting.

Note

• The Isodrive ® motor system does not include the roof seal kit or the support straps.
  Note
  Please see the Isodrive ® installation guide for motor installation information.
  Danger
  All electrical wiring from the motor to the rangehood should be kept inside the roof space.

CONDENSATAION INFORMATION

COOKING WITH INDUCTION COOKTOPS
Cooking with an induction (or similar) cooktop may produce condensation on the range hood. Unlike basic electric or gas cooking, induction cooktops heat food and liquid instantly, which in turn, produces vapors rapidly. Because of the accelerated process, the rangehood filters do not have enough time to warm up, which increases the chance of condensation forming. There are many variables that may contribute to condensation forming, some of which include but are not limited to:

• Variance in climate – geographical location.
• Position of your home & kitchen – morning/ afternoon sun.
• Distance from cooktop to the range hood.
• Speed of food & liquid heating.
• Angle of ducting – an ‘S’ bend is preferred.
• Filter size – larger rangehood preferred, as it will have a larger filter extraction area.
• Quality of pots or cookware you are using – high quality is recommended.

How to reduce the possibility of condensation forming:

• Ensure the rangehood is installed by a qualified professional, carefully following the installation guide.
• Turn on the range hood 5-10 minutes prior to cooking, and leave it on for 5-10 minutes after cooking; this helps clear remaining vapors from the flue.
• Start the cooking process at a low-to-medium setting and allow time for the rangehood to become warm.
• Clean filters regularly.
• Ensure constant airflow in the cooking zone; this helps optimize the rate of extraction.
• Follow all induction cooktop manufacturers’ advice.
• Install at recommended height above induction cooktop.

For further tips or information regarding cooking with induction, please contact the induction cooktop manufacturer.

TROUBLESHOOTING

Before you contact the technical service department, make sure that the product is plugged in and power is supplied.
• Do not take any action that will damage the product.
IMPORTANT
Never attempt to repair this appliance by yourself. Always refer to a qualified Service Technician.

Loud noise from the rangehood| Rangehood does
not direct air out
(through the chimney)| Rangehood air exaction is weak| Light does not work| Rangehood does not work|
---|---|---|---|---|---
| | | X| X| Check electric connection. The voltage of the electric network should be between 220 – 240V, and the range hood should be connected to a grounded plug and turned on.
| | | | X| Check motor switch. Please ensure that there is the power to the range hood and that the range hood is switched on.
| | | X| | Check lamp switch. The lamp switch should be in one position.
| X| X| | | Check filters. The filters should be washed regularly, see filter cleaning, page 14.
| | | X| | LEDs should be firmly in position.
| | | X| | Check LEDs.
Make sure they are not broken or faulty.
| X| X| | | Please make sure there is no obstruction in ducting or with the backdraft fins.
X| | X| | | Check the outlet, make sure it is not blocked and you have the correct diameter ducting installed.
X| | | | | Check Isodrives installation manual, make sure the ducting is installed correctly, eg. Length of ducting used, and keep the ducting taut.
| | X| | | Check the ducting has not come unattached from the rangehood outlet or has been eaten through by rodents.

SERVICE
Lodging an Online Service Request
In the event that the failure is not due to the faults mentioned in the Troubleshooting section, you can lodge an online Service Request. To lodge an online Service Request, visit our website www.schweigen.com.au/service-and- warranty and click on the link and complete the service request form.

A service request will require the following information:

• The purchase date
• The model number
• The rangehood model and motor type (eg. Isodrive ® 650)
• The serial number or batch number (this number is on a sticker inside the rangehood).
• A copy of the purchase receipt (without a receipt your service request cannot be processed). Alternatively, you can call Customer Service:

Australia
1300 881 693
New Zealand
0800 200 510
FAULTY INSTALLATION
It is not the responsibility of Schweigen to rectify any incorrect installations. A service call out fee will be charged for any Schweigen technician that attends a call, whereby it is established that the fault is due to an incorrect installation or non-manufacturing fault. Should the appliance be installed in such a way that the service agent is unable to gain access to the appliance, the person/s who own the premises or the property where the appliance resides — will be responsible to provide access to the appliance at their expense.

TECHNICAL SPECIFICATIONS

KLS-9GLASS, KLS-9GLASSBLKS

Model: KLS-9GLASS, KLS-9GLASSBLKS
Feeding Voltage: 220-240V 50Hz
Max Lamp Power: 1 x LED Strip 726mm long 3.36W 12V 3000k

DISCLAIMER

Under our policy of continuous product development, product specifications may change without notice. Prospective purchasers should therefore check with the retailer to ensure this publication correctly describes the products being offered for sale. All information supplied is to be used for general reference purposes only and is on the understanding that Schweigen Home Appliances will not be liable for any loss, liability or damage of whatever kind arising as a result of any reliance upon such information. All pictures used in the guide are for illustrative purposes only. Although our information and marketing state the term ‘Silent’ for certain models, the following applies to various models that are sold with certain Isodrive ® Systems and baffle filters. When a model with the larger motored Isodrive ® System is operated at a higher speed/s air movement may be heard. For example, while operating on speeds 4 & 5 (For 5-speed models) the rangehood may be audible due to a large amount of air movement moving through the filters.

*Please make sure that the range hood and motor have been installed as per the corresponding instruction guides in order for optimal performance (the Isodrive ® Motor  Manual can be found with the Isodrive ® Motor, or online at schweigen.com.au). Schweigen Home Appliances has presented this information in good faith to all their retailers and distributors to convey before any/all purchase/s. Information is supplied upon the condition that the person/s receiving the information will make their own determination as to its suitability for their purpose/s prior to use. In no event will Schweigen Home Appliances be responsible for damages of any nature whatsoever resulting from the use of,
or reliance upon, information from their website or the products to which the information refers.
DISPOSAL OF OLD APPLIANCES
Electronic waste (or e-waste) including kitchen appliances are banned from direct disposal to landfill. E-waste contains hazardous materials, which can harm the environment and human health. Valuable materials contained in e-waste are lost when appliances, computers, and other household electrical goods are sent to landfills.
Recycle your e-waste to:

• reduce landfill
• protect the air and waterways from harmful materials
• minimize consumption of raw materials to produce electronic products
• reduce greenhouse gases created in the production of new materials.

Kitchen appliances including Rangehoods and Ovens can only be disposed of at approved recycling centers. Visit www.recyclingnearyou.com.au/whitegoods for more information, or contact your local council or the store you purchased this appliance, for a list of approved recyclers.

© Schweigen Home Appliances Pty Ltd. Jun2022.
Australia
Unit 4/1-5 Lake Drive, Dingley Village, Victoria 3172
Phone: 1300 881 693
Email: sales@schweigen.com.au
New Zealand
5 Tolich Place, Henderson, Auckland 0610
Phone: 0800 200 510
Email: info.parex@emerson.com
www.schweigen.com.au 

References

• SCHWEIGEN Silent Rangehoods
• Recycling Whitegoods - Planet Ark Recycling Near You
• SCHWEIGEN Silent Rangehoods
• Service and Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>