DLS PA6.20 Performance Car Audio Speakers User Manual

June 12, 2024
DLS

DLS-LOGO

DLS PA6.20 Performance Car Audio Speakers

Welcome to DLS!

  • Thank you for buying a DLS Performance PA6.20. For us, it’s all about the sound experience. We care deeply about sound and construction quality. In order for your experience to be as optimal as possible, it is important that you read this manual, preferably before you start your installation. Keep the manual in a safe and accessible place for future reference.
  • Your speakers must be installed correctly in order to work as intended. Make sure you have all necessary tools nearby before starting and that you are completely confident in how to process. If you feel the slightest uncertainty; feel free to take the help of an experienced installer or a car audio dealer.

Warranty

  • This component kit is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product.

General

  • Some sound systems may vary in size of the door speaker. Make sure that your vehicle has the same size as this kit, before you start the assembly.

DECLARATION OF CONFORMITY

DLS plug and play speakers for vehicles are manufactured in accordance with the EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval number. They are also marked in accordance with the WEEE-directive 2012/19/EC. The products are also produced in accordance  with the EU RoHS directive 2015/863/EU.

Included parts

Included products

  • 2pcs Woofer
  • 2pcs Tweeter
  • 2pcs Crossover (including 2 x 50cm cable)

Included in box

  • 2pcs Tweeter bottom adapters
  • 2pcs Tweeter cable 100cm (for loose ends)
  • 2pcs Adhesive foam
  • 8pcs V-type clips
  • 8pcs Screws
  • 2pcs Grills
  • 1pcs Manual

Pre-installation

  • Disconnect Battery Before you start the process of replacing speakers, disconnect and secure the negative terminal from your battery/power source. This will prevent the risk of damaging yourself or the products
  • Place the disconnected terminal in a secure and isolated location away from any possible connection belonging to the battery/power source system.

Installation

  • Mount the speakers in the door or in the dashboard of your car. They may fit in the factory pre-made mounting holes, if not you might have to modify the fitting. If you want to improve the sound reinforcement you can use a baffle of MDF-board or similar. An installation high up on the door side is to be prefered. For door placements, there are normally speaker rings that have to be used to make the speaker fit to the door panel.
  • In many vehicles there are factory made places for tweeters that you can use for installation. If this is not possible, try to install the tweeter close to the bass/midrange driver. The tweeter can also be installed on the dash-board, or recessed in the door with the accessories included with the tweeters. NOTE! It is important to fasten the speakers properly in order to avoid bad sound or rattling. Connect the speakers and crossovers as in the drawing below.

DLS-PA6-20-Performance-Car-Audio-Speakers-FIG-2

Installation of tweeter
The tweeter can be mounted on the dashboard with the included angled housing, or recessed in a door side.
Surface mounting
Put the cable through the hole in the rear end of the angled housing. The tweeter is attached to it by putting them together and turn clockwise. Attach the housing to the surface with the included double adhesive tape.
Recessed mounting
You need a hole with a diameter of 43 mm/1.7”. Use glue to attach the recessed housing to the A-pillar, or door panel. The tweeter is attached to the housing by putting the tweeter into it and turning clockwise.

Door insulation
DLS recommends using insulation/sound deadening in the car doors. It lowers the noise from the road/tires and prevent rattles and other noises from plastic details in the doors.
If you need help deciding what type of door insulation you should use, ask your DLS distributor for info and guidance.

Running-in time

  • Allow the component kit to play for at least 15-20 hours in order to perform at its possibly best. This run-in can be made with tone sweep or with just music.
  • Start at a moderate volume and increase the volume step by step during the running in period. After the 15-20 hour run in session the performance and characteristics will be in the correct condition.

DLS support

For technical assistance, ask your car audio dealer where the product was sold or the distributor in your country. You can always contact the DLS Helpdesk in Sweden at e-mail: info@dls.se Information can also be found on our WEB-site www.dls.se We follow a policy of continuous advancement in development. For this reason, all or part of specifications & designs may be changed without prior notice.

Wiring diagram

DLS-PA6-20-Performance-Car-Audio-Speakers-FIG-5

Specifications

Art. no PA6.20

  • Woofer: 6.5” /165 mm with polypropylene cone
  • Tweeter: 0,8” / 20 mm silk dome tweeter
  • RMS Power: 60W
  • MAX Power: 120W
  • PEAK Power: 180W
  • Impedance: 4 Ohm
  • Sensitivity: 89dB 1W/1M
  • Freq. range: 65Hz-20kHz
  • Crossover: 5kHz 12dB/Oct

DLS PA6.20 Tweeter Technical Specification

  • Size: 0,8” /20 mm
  • RMS Power: 40W
  • MAX Power: 80W
  • PEAK Power: 120W
  • Frame: Reinforced ABS
  • Magnet: Neodymium
  • Cone: Natural silk dome
  • Impedance: 4 ohm
  • Freq. range: 3000Hz-20kHz

DLS-PA6-20-Performance-Car-Audio-Speakers-FIG-6

DLS PA6.20 Woofer
Technical Specification

  • Size: 6,5” /165 mm
  • RMS Power: 60W
  • MAX Power: 120W
  • PEAK Power: 180W
  • Basket: Steel
  • Magnet: Ferrite
  • Cone: Polypropylene
  • Impedance: 4 ohm
  • Freq. range: 65Hz-5kHz

DLS-PA6-20-Performance-Car-Audio-Speakers-FIG-7

Product markings

  • The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.

  • This product has been granted with the CE certification mark to show that the product follows the health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).

  • DLS products complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions.

  • DLS is a global partner of the European Mobile Media Association, an organisation that focus on promoting the custom made mobile media installations to consumers.

We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. We reserve for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories.

DLS speakers are engineered by DLS Sweden, a part of

  • Winn Scandinavia AB
  • Elementvägen 15 – SE-702 27 Örebro – Sweden
  • Tel: +46 19 20 67 65 – E-mail: info@dls.se
  • www.dls.se

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals