DLS RC6.2Q 2-Way Speakers System Owner’s Manual

June 4, 2024
DLS

RC6.2Q 2-Way Speakers System
Owner’s Manual

Welcome

Thank you for buying a DLS speaker. This model is a part of the DLS Reference speaker line. Install the speakers yourself if you feel confident with our instructions and if you have the proper tools. A poor installation job can destroy the final result even from these speakers, so if you feel unsure, turn over the installation job to someone better suited to it.

Installation

Mount the speakers on the door or in the dashboard of your car. Normally they will fit in the factory’s premade mounting holes. If you want an improved sound to reinforce with a baffle of MDF-board or similar. An installation high up on the door side is to be preferred.
In many vehicles, there are factory-made places for tweeters that you can use for installation. If this is impossible, try to Install the tweeter close to the bass/mid driver. The tweeter can also be installed on the dashboard, or recessed in the door with the accessories coming with the tweeters.
It is important to fasten the speakers properly in order to avoid bad sounds or rattling. Connect the speakers to the crossovers as in this drawing:

Connection of crossover RC6.2Q

DLS RC6 2Q 2 Way Speakers System - Fig 1

Installation of tweeter RC28
RC28 can be mounted on the dashboard with the angled cup (1) cup, or recessed in a door side.

Surface mounting:

For an angled surface mount use the angled cup:
The tweeter driver is attached to the cup by fitting the three wings on the angled cup into the tracks of the tweeter driver and then turning it clockwise to lock. When removing the driver from the cup, turn it CCW and lift it up. The cable goes through the hole in the rear side of the cup.

Recessed mounting:
Drill a hole with a diameter of 48 mm/1,89” in the door side. The cup (2) is attached to the door side with the metal wing(3) pressed to the back side of the door. Fasten the metal wing using the two M3 screws.
Put the tweeter driver (1) into the cup with the cable going out through the bottom hole. Then attach the driver to the cup and turn it clockwise to lock in the cup. When removing the driver from the cup, turn it CCW and lift it out.DLS RC6 2Q 2 Way Speakers System - Fig 3

Technical data RC28 tweeter

Size 28 mm / 1,1”
Nom. power handling (RMS) 50 Watt, 80 Watt max
Frequency response 1,5 kHz-25 kHz
Sensitivity 93 dB
Magnet diameter 35 mm / 1,38” neodymium magnet
Mounting depth 20 mm / 0,8” (recessed install)
Mounting hole 48 mm / 1,9” (recessed install)
Cone material Textile fiber

Technical data bass driver
DLS RC6.2Q

Impedance 4 ohm
Nom. power RMS 100 W
Max/peak power 150 W / 300 W
Cone material Black anodized aluminum
Woofer size 6,5”(16,5 cm)
Magnet size 110 mm/4”
Sensitivity 86 dB
Mounting depth 75 mm/2,95”
Mounting hole 145 mm / 5,7”

Warranty service

This speaker is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt (or a copy) with the product.

Technical Assistance
For technical assistance ask the shop where the product was sold or the distributor in your country.
You can also send an e-mail to info@dls.se
Information can also be found on our website www.dls.se
We follow a policy of continuous advancement in development.
For this reason, all or part of specifications & designs may be changed without prior notice.

DLS Logo DLS Svenska AB
Tagenevägen 11B
42259 Hisings Backa, Sweden
Tel: 031-840060
E-mail: info@dls.se
www.dls.se

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals