KICHLER 37431A Bayley 23 Inch 3-Light Olde Bronze Industrial Vanity Light Instruction Manual

: June 12, 2024
: KICHLER

Table of Contents

PACKAGE CONTENTS
HARDWARE CONTENTS
SAFETY INFORMATION
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 37431A Bayley 23 Inch 3-Light Olde Bronze Industrial Vanity Light Instruction Manual

PACKAGE CONTENTS

PART	DESCRIPTION	QUANTITY
A	Canopy	1
B	Mounting Bracket	1
c	Socket	3

HARDWARE CONTENTS

**AA

Wire Connector Qty:** 3

**BB

Short Machine Screw Qty** : 2

**CC

Threaded Knob Qty:** 2

**DD

Long Machine Screw Qty:** 2

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Do not use bulbs with wattage greater than specified on this fixture.
California Proposition 65

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm.
For more information, go to http://www.P65Warnings.ca.gov

CAUTION

If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses.

ASSEMBLY INSTRUCTIONS

Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box. Insert long machine screws (DD) through mounting bracket (B). With long machine screws (DD) protruding outward, connect the mounting bracket (B) to the outlet box (not included) with short machine screws (BB).
Assembly Instruction
Hardware Used

BB **

x 2
Short Machine Screw
DD

x 2
** Long Machine Screw

Wire connection guide:
Ground wire:

For installation in the United States: Wrap ground wire from outlet box around ground screw on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).
For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with the wire connector (AA).

Assembly Instruction

Supply wires:

Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).

Supply Wires

NOTE:

Fixture wires will either be:
Black and White.
Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.

AA Wire Connector

x 3

Pass canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure in place with threaded knobs (CC).
Assembly Instruction
CC Threaded Knobs

x 2
Insert 60-watt max. medium base bulb or LED equivalent (not included) into socket (C). Repeat for remaining sockets.
Assembly Instruction

CARE AND MAINTENANCE

Always be certain that electric current is turned off before cleaning this item.
Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on
fixture, as it will damage the metal finish.
All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.