CYC Gen 3 Upgrade Feature Summary User Manual
- June 12, 2024
- CYC
Table of Contents
CYC RIDE CONTROL
App User Guide
support@cycmotor.com
« +852 3690 8938
Introduction
CYC RIDE CONTROL
Monitor & customize your e-bike riding experience for all CYCMOTOR mid-drive
systems. Use it as a secondary dashboard, settings set-up, or both. Unleash
all the possibilities of e-bike customization at your fingertips.
The mobile app is not the only way to customize your system. The controller is
also programmable via the included display- integrated for your convenience.
This platform is your go-to-station for your CYCMOTOR kit and X-Series
controllers.
FEATURES
- Bluetooth connectivity
- Complete with torque sensor configuration
- Compatible with X6 &X12 controllers
- Real-time dashboard for all your motor & riding information
- Fully customizable parameters for pedal assist, throttle & gear preferences
Dashboard
CONNECTING A DEVICE
STEP #1:
Open the app and tap the Search button at the bottom of the screen. Kindly
ensure your phone’s Bluetooth is enabled. (Please keep close to the motor
while connecting)
STEP #2:
Available devices will then be listed, select your kit and it will begin
connecting to the controller. (Please note signal strength)
STEP #3:
Once connected, the CONNECT icon will change stating you are connected & can
select again to disconnect.
MAIN SETTINGS
The settings page allows you to navigate through different parameter
categories. There are six different categories with each providing a set of
adjustable parameters or readings from your ebike system.
IMPORTANT
Save all new changes in parameters to flash or risk losing progress. Any
changes made that were not saved will be lost after a restart. Note to save
after every change in value.
To save to flash, tap the ‘Save’ button in the upper righthand corner, ‘Save
successful’ message will appear upon completion.
GENERAL
TEMPERATURE UNIT
Set your units to display in degrees Celsius (°C) or Fahrenheit (°F)
SPEED UNIT
Set the speed unit to miles or kilometers.
MOTOR DIRECTION
This setting is for users who’d want to switch the direction to where the
motor is facing.
Note that this is reserved for specific uses only.
WARNING: Do not change this setting if using the motor in its default
position. Contact CYC for assistance.
RESTORE DEFAULT SETTINGS
Restore to factory/default settings.
MODES & LEVELS
RACE & STREET MODE
You can set the throttle & PAS output independently for both modes.
RACE MODE THROTTLE &PAS
Race Mode is your”boost” or”full power” mode and has parameters set for
reaching closer to the system’s full capabilities. You can adjust these to
your own preference within the capabilities of your controller. The default
setting in Race Mode is 3000W & 100 km/hr.
STREET MODE THROTTLE & PAS
Street Mode is intended to be set to your region’s legal limits. You can
adjust these to your own preference or to your region’s legal limits. You can
adjust these to your own preference or to your region’s legal limits. The
default setting in Street Mode is 750W & 25Km/hr.
THROTTLE
RAMPING TIME
This is the time it takes for the motor to achieve the required input. For
example, if you open the throttle fully, it will take 250ms (by default)
before the motor gives you full power.
It will gradually ramp up to full power within the set time. We recommend not
to set this below 1 SOms.
INPUT DEADBAND
This value pertains to opening the throttle when it’s completely closed. This
is the amount of throttle can be moved from the zero position without
generating a response from the motor.
If this value is set lower, your throttle will engage quicker and vice versa.
MAX VOLTAGE
This value should be the same as the Throttle Voltage Reading when the
throttle is closed and sets the output when it is not active.
MIN VOLTAGE
This is the output of the throttle when opened fully and is pre-set when
purchased. This does not need any change with CYC supplied throttles.
THROTTLE AUTO SETUP
If you’d like to use your own throttle, this will automatically setup the
minimum and maximum voltage accordingly. Follow the steps as prompted on the
screen.
PEDAL ASSIST
PEDAL ASSIST SENSOR
Enabling pedal assist.
TORQUE SENSOR SENSITIVITY
This value pertains to activating pedal assist when it’s completely off. This
is the amount of pedal force required to activate the pedal assist. If this
value is set higher, your pedal assist will engage with less force and vice
versa.
POWER RAMP TIME
The amount of time it takes to reach the desired input. This is the
responsiveness of the motor.
MOTOR ASSIST FACTOR
This value pertains to how hard you need to pedal to get full power.
CADENCE START
This feature allows for a cadence-free pull away. i.e., only torque (40N.m.)
is required to activate pedal assist.
PEDAL BACKWARDS CUTOFF
This features allows you to cut the motor power when you pedal backwards.
PERIPHERALS SETUP
SPEED SENSOR
Wheel Diameter
The wheel diameter can be measured or calculated. We advise that this number
must be calibrated so that vehicle speed within the app matches display speed.
This will give more accurate speed liming under different modes.
Remember to set the correct wheel size within the display as well (only
applicable to 500c & 750c displays). Kindly refer to your user manual.
Wheel Magnet
This is the number of magnets in the wheel that is communicating with the
speed sensor.
For more accurate vehicle speed limiting and measurement, we advise to add
more magnets to the wheel.
BRAKE SENSOR
Enable/Disable brake sensors
INVERT BRAKE SENSOR SIGNAL
If you are using brake sensors from a different supplier, you can use this
feature to set up your brake sensors as needed.
WARNING
Please contact your authorized dealer or CYC support if you’re setting up
third-party peripherals.
DISPLAY
THERMAL PROTECTION
This is an advanced feature and requires a password from CYC to change. This
allows you to disable your motor temperature sensor.
Contact
technical_support@cycmotor.com for
more details and password for this feature.
BATTERY
BATTERY TYPE/ SERIES OF CELLS
1 Os = 36V, 14s = 52V, 20s = 72V
MINIMUM VOLTAGE
The value the controller will fault when connecting too low a voltage to the
system.
This setting can be used to protect your battery if too much voltage sag is
detected.
DISCLAIMER
If you require any more information or have any questions about the user
manual disclaimer, please contact us via email at technical
support@cycmotor.com.
All information contained in this user’s guide is published in good faith and
for general informational purposes only. CYCMOTOR LTD does not make any
warranties about the completeness of this information and encourages further
inquiries as stated above if needed. CYCMOTOR LTD will not be held liable for
any losses and/or damages caused by negligence or misinterpretation.
PRIVACY POLICY
This service is provided by CYCMOTOR LTD. at no cost and is intended for use.
This text is used to inform visitors regarding our policies with the
collection, use, and disclosure of personal information if anyone decided to
use this service. If you choose to use this service, then you agree to the
collection and use of information in relation to this policy. The personal
information that we collect is used for providing and improving the service.
We will not share your information with anyone except as described in this
Privacy Policy. The terms used in this Privacy Policy have the same meanings
as in our Terms and Conditions, which is accessible at CYCMOTOR LTD unless
otherwise defined in this Privacy Policy.
Information Collection and Use
For a better experience while using this service, we may require you to
provide us with certain personally identifiable information, including but not
limited to Name (optional), Phone number, Email address, Location (Optional).
The information that we request will be retained by us and used as described
in this Privacy Policy.
Visit www.cycmotor.com/privacy-policy for more detailed information.
©2023 CYCMOTOR LTD
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>