ZEMISMART ZMS1 Smart Slide Curtain Instructions

Smart Slide Curtain
Instruction

Specification

Product instruction

Track splicing

1. Open the lock of sub gear box, and take off the box.
2. Insert the track buckle into the track . fix one side.
3. insert 0.6m track into the other side of track buckle,then splice two tracks tightly, lack the buckle.
4. Install the sub gear box again, and pull the positioner to the end of the track at sub-gear boxside, lock the buckie of sub gear box when hear a sound of click.
5. Open the lock of the master carrier, then pull the two carriers to the each end of the track, then lock of the master carrier. Now the whole track splicing is finished.
6. Engouh runners have been put into track in factory, custamer can increase orreduce the number of runners as require. ( 8pcs/m)

Track installation

Please install the celling bracket before installing the track, and measure the distance te fix the celling bracket, then clip the track into the bracket. NOTE: There must be 1 bracket around the master/sub-gear box and track buckle, the bracket quantity will be increased by 1 for each additional meter of track length.

Curtain motor installation ;

Insert the motor head into the groove of the master gear box ,turn it 90° counterclockwise.

Disassemble of curtain motor

Pull the motor buckle ,turn it 90°clockwise,remove the motor.

Motor pair to remote control

Note: There ts single channel emitter included in kit, ithas been coed with motor, can work with the motor directly.

Speed adjustment

There are 3 levels of motor running speed : Silent level,low-speed level and high-speed level, the initial running speed is silent level.

Method 1 ; Press the OPEN button three times continuausly to adjust the speed . Method 2: Press the CLOSE button three times continuously to adjust the speed.

Set the limit

When motor is powered on, let it run a complete opening and closing once, the limit position will be automatically set at the end of each running.

1. Set the limit position of opening/closing
   Let the motor stap at the designated position first press OPENand CLOSE atthe same time until the moto rvibrates once, the yellaw indicator stays on for a while Then press STOP Stimes, each time you press the indicator light turns on and off alternately and the light goes out after Sth pressing Next press OPEN/CLOSE once,the motor vibrates once.set the limit positian of opening/closing is successful

2. Delete the limit position of opening/closing Press OPEN and CLOSE atthe same time the motar vibrates ance Lhe yellow indicator light stays on for a while Press STOP 3times each time you press the indicatar lightturns on and off alternately and the light goes out after the third pressing Press the OPEN/CLOSE once moter vibrates once, we delete the limit positions of opening/‘closing successfully

3. Release the control of current remote/all remote controls Press OPEN and CLOSE atthe same time the motar vibrates ance Lhe yellow indicator light stays on for a while Press STOP 7 times, each time you press the indicator light lurns on and off alternately and the light goes out after 7th pressing Then press CLOSE/OPEN the motor vibrates once release the current remote control/all remate controls successfully

Change direction

Motor pair to APP

1. Matter over thread version
   Note:
   1. A Matter-certified ecosystem smart home app is required.
   2. AHome hub is required to set up matter-certified devices.
   3. Setup processes may vary between ecosystems. In this user manual just make Apple Home APP and Google Homekit APP for explame.
   4. Limit setting is necessary before use APP to control.
   1 Reset Motor2 Turn on WiFi on your phone. 3 Open yaur selected smart home app and scan the Matter QRcode on the motor.
   A: Follow the below instructions to set up on Apple Home APP,B: Follow the below instructions to set up on Google Home APP.

2. Tuya version
   1 Reset Motor 2 Turn on the bluetooth and WiFi on your phone. A: Tuya WiFi versian
   Go into Tuya APP main page, click on the up-right button” +” ,then follow these steps to complete the pairing.B: Zigbee version
   Go into Tuya Zigbee hub page,then fallow these steps to complete the pairing

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the timits fara Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation, This equipment generates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, May cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by ane or more of the following measures:

• Rearient or relacate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radia/TV technician for help.

FCC Radiation Exposure Statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>