PANGEA AUDIO PGWMSSE2 Vulcan Turntable Wall Mounted Premier SE Shelf MKII Owner’s Manual
- June 13, 2024
- PANGEA AUDIO
Table of Contents
PANGEA AUDIO PGWMSSE2 Vulcan Turntable Wall Mounted Premier SE Shelf MKII
PRODUCT INFORMATION
- PANGEA.A: AN AMERICAN COMPANY
- Model: PGWMSS E2
Included Parts
| NO. | DESCRIPTION | QTY |
|---|---|---|
| A | M8x25 | 2 |
| C | MB 8 | 2 |
| E | M6 | 2 |
| F | 8 | |
| G | 8 | |
| H | 8 | |
| I | MS J M4 | 1 |
| K | 13mm-10mm | 1 |
| L | 1 | |
| E M | ~ 1 | |
| 10 | ~ 1 |
- Step 1: Tools Needed
1. Level
2. Electric Drill
3. Phillips Screwdriver
4. Stud Finder
5. Pencil/Pen
6. Tape Measure (Optional) Use caution to avoid electrical wires, pipes, or any other in-wall hazards that cannot be seen through drywall. If you are unsure before you drill, call a professional for installation.
- Step 2: Mounting on Wall Studs (Preferred)
1. Locate and lightly mark wall studs and voids with a stud finder (not included).
2. Level the backplate (M) in the desired position against the wall.
3. Using the marks from step #1 as a guide, mark stud locations using backplate (M) as the template.
4. Use drill bit (L) to drill holes through the drywall into the studs.
5. Place screw (D) through screw cap (F).
6. Put the screw through the backplate and into the drilled hole, while placing the backplate against the wall.
7. Hand tighten the screw against the backplate until firmly seated (do not overtighten).
8. Snap screw cap (F) closed.
9. Repeat for all other mounting spots. Note: Most studs are spaced 16″ on center, and this is the preferred method of mounting. It is recommended that at least four (4) screws are seated firmly into wooden studs. Mounting only on drywall is dangerous and reduces the weight capacity of the shelf considerably. The drywall anchors are only supplied to supplement the stud-mounted screws.
- Step 3: Mounting on Drywall (Only if Needed)
1. Locate and lightly mark wall studs and voids with a stud finder (not included).
2. Level the backplate (M) in the desired position against the wall.
3. Using the marks from step #1 as a guide, mark voids for drywall anchors (G) using backplate (M) as the template.
4. Drill into drywall using drill bit (L) to create a starter hole for the drywall anchor (G).
5. Turn the drywall anchor into the drywall with a Phillips screwdriver until flush with the wall.
6. Place screw (D) through screw cap (F).
7. Put the screw through the backplate and into the drywall anchor, while placing the backplate against the wall.
8. Hand tighten the screw against the backplate until firmly seated (do not overtighten).
9. Snap screw cap (F) closed.
10. Repeat for all other mounting spots.- Step 4
1. Put the shelf (0) on spikes, aligning the spikes with the caps on the underside of the shelf.
2. Level the shelf, left to right, and front to back, by adjusting the threaded spikes (C).
3. Using wrench (K), tighten locknuts.
4. Place stickers (H) over unused holes as needed. For more products from Pangea Audio, visit www.pangeaaudio.com
Included Parts
Tools Needed
- Level
- Electric Drill
- Phillips Screwdriver
- Stud Finder
- Pencil/Pen
- Tape Measure (Optional)
Use caution to avoid electrical wires, pipes, or any other in-wall hazards that cannot be seen through drywall.
If you are unsure before you drill, call a professional for installation.
INSTALLATION INSTRUCTION
- **Step 1
**
- **Step2
**
- Step 3A
Mounting on wall studs (preferred):
1. Locate and lightly mark wall studs and voids with a stud finder (not included).
2. Level (not included) the backplate (M) in the desired position against the wall.
3. Using step #1 marks as a guide, mark stud locations using backplate (M) as the template.
4. Use drill bit (L) to drill holes through the drywall into the studs.
5. Place screw (D) through screw cap (F).
6. Put the screw through backplate and into the drilled hole, while placing the backplate against the wall.
7. Hand tighten screw against backplate until firmly seated (do not overtighten).
8. Snap screw cap (F) closed.
9. Repeat for all other mounting spots. Note: Most studs are spaced 16″ on center, and is the preferred method of
mounting. It is recommended that at least four (4) screws are seated firmly
into wooden studs. Mounting only on drywall is dangerous, and reduces the
weight capacity of the shelf considerably.
The drywall anchors are only supplied to supplement the stud-mounted screws.
- Step 38
Mounting on drywall (only if needed):
1. Locate and lightly mark wall studs and voids with a stud finder (not included).
2. Level (not included) the backplate (M) in the desired position against the wall.
3. Using step #1 marks as a guide, mark voids for drywall anchors {G) using backplate (M) as the template.
4. Drill into drywall using drill bit (L) to create a starter hole for the drywall anchor (G).
5. Turn drywall anchor into drywall with a Phillips screwdriver until flush with wall.
6. Place screw {D) through screw cap (F).
7. Put screw through backplate and into the drywall anchor, while placing the backplate against the wall.
8. Hand tighten screw against backplate until firmly seated (do not overtighten).
9. Snap screw cap {F) closed.
10. Repeat for all other mounting spots.
- Step4
- Put shelf (0) on spikes, aligning the spikes with the caps on the underside of the shelf.
- Level the shelf, left to right, and front to back, by adjusting the threaded spikes (C).
- Using wrench (K), tighten locknuts.
- Place stickers (H) over unused holes as needed.
For more products from Pangea Audio, visit WWW.PANGEAAUDIO.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>