DURATECH DLT10-BIC Touch Built In Charger User Manual

June 12, 2024
DURATECH

DURATECH logo DLT10-BIC Touch Built In Charger
User Manual
 DURATECH DLT10-BIC Touch Built In Charger -
WALLMOUNT Manual
DLT10-BIC
LINK Touch
Built-In Charger

ABOUT THE DLT10-BIC (BUILT-IN CHARGER)

The DLT10-BIC is an optional method for mounting the LINK TouchTM near the swimming pool. It is based on a Power Supply and flush mounted socket with USB-Connection.
The Power Supply allows a direct connection to the mains and provides the right power to the socket for the LINK TouchTM . When the LINK TouchTM is inserted in the wallmount, connected to the DLT10-BIC, it will charge until he battery is full.
The main advantage of the DLT10-BIC is related to the aesthetics, whereby that the Power Supply and Cables (Power and USB), needed for the Link TouchTM , are invisibly covered in the wall.

TECHNICAL SPECIFICATIONS

Power Supply:
Input Voltage: 100 – 240 Volt
USB Output Voltage: 5V DC
USB Output Current: 2.1A
USB Type: Type A
Power Supply is CE Compliant
Electric Box:
Diameter: 67,00 mm
Depth: 40,00 mm
Two screws are pre-installed on the part.
USB-Cable:
Voltage Rating: 5V DC
USB Type: USB-A to USB-C

PACKAGING CONTENTS

ITEM NO. PART NUMBER / DESCRIPTION QUANTITY
1 402 – 0596 QSG Manual ; DLT10-BIC 1
2 501 – 0184 Cable ; USB-A to USB-C 1
3 510 – 0162 Screw Cap ; Wall Mount ; LINK Touch 2
4 510 – 0554 Bracket 1
5 513 – 0307 Wallmount ; Assembly ; LINK Touch 1
6 513 – 0666 USB Power Module ; 5V DC ; 2,1A 1
7 513 – 0667 Electric Box for Drywalls ; 67,00 mm 1

DURATECH DLT10-BIC Touch Built In Charger - PACKAGING
CONTENTS

SAFETY INSTRUCTIONS

Before installation and use of the DLT10-BIC, the basic safety instructions need to be understood.Specific contents include the following warnings:

  1. Be careful of electric shock.
  2. Make sure to turn off the fuse of the circuit you will be working on.
  3. Failure to comply with safety instructions may result in serious body injury or death.
  4. The installation of the DLT10-BIC must be done by professional pool service personnel, installers or operators.
  5. The national standards and regulations for installation should be followed.
  6. Contact a licensed electrician or building inspector for information on local electrical codes for installation requirements.

Intended use
This device has been developed to connect and mount the LINK TouchTM .
The DLT10-BIC should be used only for this purpose, as described in this user guide.
Precautions for Setup
– The DLT10-BIC can only be mounted indoor. Do not mount outdoors.
– The Power Adapter is designed for 100 – 240V, 50/60 Hz. Verify if the power outlet voltage is within this range before plugging in your Power Adapter.
– Make sure the Power/USB-Cable are not strained or pinched.
– Do not use the USB-Cable when damaged or frayed.
– Be sure to hold only the connector end of the USB-Cable when disconnecting.
Precautions for Operation
– Protect the Built-In Charger from moisture.
– Never spill liquid of any kind on the DLT10-BIC.
Precautions for Cleaning, Transport and Storage
– This DLT10-BIC contains no user serviceable parts. Do not attempt to service the DLT10-BIC yourself. Repair service should be performed by a authorised technician.

INSTALLATION INSTRUCTIONS

STEP 1: INSTALL ELECTRIC BOX.
Make sure to turn off the fuse of the circuit you will be working on! The Electric Box can be used in concrete wall and thin drywalls.
Insert the power cables into the Electric Box, through the soft silicone inserts featured in the Electric Box.
Lock the Electric Box into place, by turning the two long screws with a Philips Screw Driver.DURATECH DLT10-BIC Touch Built In Charger - ELECTRIC
BOX STEP 2: INSTALL POWER SUPPLY.
The Power Supply features a terminal block at the back.
Place both power cables into the terminal block and use a Philips Screw Driver to lock the cables into place.
Position the Power Supply into the Electic Box by bending the power cables. DURATECH DLT10-BIC Touch Built In Charger - POWER
SUPPLY STEP 3: INSTALL THE USB-CABLE.
Insert the USB-A connector from the USB-Cable into the Power Supply. Make sure the connector is facing upward!
Insert the USB-C connector from the USB-Cable into the bottom of the Wallmount.
Position the Bracket at the back of the Wallmount. Make sure the USB-Cable is going OVER the bracket to garantee a good fi tment between the Bracket and the Electric Box. DURATECH DLT10-BIC Touch Built In Charger - USB-
CABLESTEP 4: INSTALL THE WALLMOUNT.
Lock the Wallmount onto the Electric Box using the two short screws that are pre-installed in the Electric Box.
The Bracket should fi t perfectly into the electric box and keep the Wallmount in place when thightening the screws.
After positioning the Wallmount into place, use the Screw Covers to fi nish the installation.DURATECH DLT10-BIC Touch Built In Charger -
WALLMOUNT STEP 5: CHARGE THE LINK TouchTM.
Make sure to turn back on the fuse of the circuit you have been working on!
Place the LINK TouchTM onto the Wallmount and verify if the LINK TouchTM is charging.
When charged, the LINK TouchTM can be used.DURATECH DLT10-BIC Touch Built In
Charger - WALLMOUNT 1

SERVICE & WARRANTY

If you need service or information or if you have a problem, please contact your local dealer. If needed they will contact the manufacturer to solve your problem.
They are gladly willing to assist you!
You can fi nd more information at www.duratech.be
We warrant all parts to be free from manufacturing defects in materials and workmanship for a period of two years from the date of retail purchase.
This warranty is limited to the fi rst retail purchaser and is not transferable. The liability of the manufacturer shall not exceed the repair or replacement of defective parts and does not include any costs for labour to remove and reinstall the defective part, transportation to or from the factory, and any other materials required to make the repair.
This warranty does not cover failures or malfunctions resulting from the following:

  1. Failure to properly install, operate or maintain the Built-In Charger in accordance with the installation guidelines provided in this manual.
  2. The workmanship of any installer of the product.
  3. Abuse, alteration, accident,fire, flood, lightning, rodents, insects, negligence or acts of god.
  4. Use of non-factory authorized parts or accessories in conjunction with the product.

Limitation of Liability
This is the only warranty given by the manufacturer, No one is authorized to make any other warranties on our behalf. This warranty is in lieu of all other warranties, expressed or implied, including but not limited to any implied warranty of fitness for a particular purpose and merchantability. We expressly disclaim and exclude any liability for consequential, incidental, indirect or punitive damages for breach of any expressed or implied warranty.
This warranty gives you specifi c legal rights, which may vary, by country.
Warranty Claims
For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number and date of installation.
The dealer will contact the manufacturer for instructions regarding the claim and determine the location of the nearest service point.

ENVIRONMENTAL / DISPOSAL OF OLD EQUIPMENT

This symbol of a crossed out waste bin on a product, its packaging and/or accompanying documents means that the product is subject to the European Directive 2002/96/EC as well as national law for implementation of the directive. Directive and law prescribe that electrical and electronic products must not be disposed of with household waste. The customer must dispose of the product by delivering it to a designated station for collection, treatment and recycling of waste electrical and electronic equipment. The correct disposal of your old appliance is free of charge and will help prevent potential negative consequences of the environment and human health.
For more information about disposing your old appliance, contact your city office, waste disposal service, or the shop where you purchased the product.

REGULATORY COMPLIENCE

This device complies to the European Harmonized Standards.
Operation is subject to the following conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

DURATECH logoDURATECH DLT10-BIC Touch Built In Charger -
FIG Contact details
Propulsion Systems bvba
Dooren 72
1785 Merchtem, Belgium
Tel +32 2 461 02 53
Fax +32 2 706 59 60
www.duratech.be
info@propulsionsystems.beDURATECH
DLT10-BIC Touch Built In Charger - QR CODEhttp://www.propulsionsystems.be DURALINK
We reserve the rights to change all or part of the contents of this document without prior notice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals