hp OMEN 34c 34 Inch Ultrawide Curved Gaming Monitor User Guide

hp OMEN 34c 34 Inch Ultrawide Curved Gaming Monitor

Product Information

a trademark owned by its proprietor and used by HP Inc. under
license. NVIDIA is a trademark and/or registered trademark of
NVIDIA Corporation in the U.S. and other countries. USB Type-C and
USB-C are registered trademarks of USB Implementers Forum.
DisplayPort and the DisplayPort logo are trademarks owned by the
Video Electronics Standards Association (VESA) in the United States
and other countries.
Warranty| The only warranties for HP products and services are set forth
in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or
editorial errors or omissions contained herein.
Edition| First Edition: Feb. 2023
Document Part Number| N31097-OMEN 34cMSG-V1
Assembly Part Number| N31097-001

Product Usage Instructions

Important Safety Information

Carefully read the cautions and notes within this document to minimize the risk of personal injury to service personnel. The cautions and notes are not exhaustive. Proper service methods are important to the safe, reliable operation of equipment. Improper service methods can damage equipment. The service procedures recommended and described in this service manual provide effective methods of performing service operations. Service engineers should have prior repair knowledge and experience as well as appropriate training for the product before performing service procedures.

Be sure your working environment is dry and clean and meets all government safety requirements. Be sure that other persons are safe while you are servicing the product. Do not perform any action that can cause a hazard to the customer or make the product unsafe. Use proper safety devices to ensure your personal safety. Always use approved tools and test equipment for servicing. Never assume the product’s power is disconnected from the main power supply. Check that it is disconnected before opening the product’s cabinet. Modules containing electrical components are sensitive to electrostatic discharge (ESD). Follow ESD safety procedures while handling these parts. Some products contain more than one battery. Do not disassemble or expose a battery to high

This guide provides information about spare parts, removal and replacement of parts, diagnostic tests, problem troubleshooting, and more.

Getting started

Read this chapter to learn about safety information and where to find additional HP resources.

Important safety information

Carefully read the cautions and notes within this document to minimize the risk of personal injury to service personnel. The cautions and notes are not exhaustive. Proper service methods are important to the safe, reliable operation of equipment. Improper service methods can damage equipment. The service procedures recommended and described in this service manual provide effective methods of performing service operations. Service engineers should have prior repair knowledge and experience as well as appropriate training for the product before performing service procedures.

• Be sure your working environment is dry and clean and meets all government safety requirements.
• Be sure that other persons are safe while you are servicing the product.
• Do not perform any action that can cause a hazard to the customer or make the product unsafe.
• Use proper safety devices to ensure your personal safety.
• Always use approved tools and test equipment for servicing.
• Never assume the product’s power is disconnected from the main power supply. Check that it is disconnected before opening the product’s cabinet.
• Modules containing electrical components are sensitive to electrostatic discharge (ESD). Follow ESD safety procedures while handling these parts.
• Some products contain more than one battery. Do not disassemble or expose a battery to high temperatures, such as throwing into fire, or the battery may explode.
• Refer to government requirements for battery recycling or disposal.

This information provides general service information for the monitor. Adherence to the procedures and precautions is essential for proper service.

IMPORTANT:  Only trained service personnel who are familiar with this HP product should perform service or maintenance for it. Before performing any service or maintenance, personnel must read the important safety information.
IMPORTANT: You must disconnect the power cord from the power source before opening the monitor to prevent component damage.

Important service information and precautions

• Repair must be performed by professional service technicians in a repair center. End users should not perform these procedures.
• Please note during servicing that the primary side is the high voltage area.
• This monitor meets ROHS requirements. Be sure to use lead-free solder wire when soldering.
• If you must change a capacitor, be sure to match the polarity as printed on the PCB.
• If you must replace a capacitor, make sure the specification and part number match the BOM and location.
• If you must replace a capacitor, insert new parts carefully to avoid a short circuit caused by the near pin.
• Do not get the board wet. Water and moisture can cause a short circuit that causes malfunctions.
• To avoid damage, be sure to use lead-free solder.
• When soldering, work quickly to avoid overheating the circuit board.
• Keep the soldering iron tip clean and well tinned when replacing parts.
• After repair, perform a close inspection of the circuit board to confirm it is in good condition.
• After repair, perform a function test to confirm the power supply is working properly.

ERP Lot5 requirement

1. A professional repairer must have the technical competence to repair electronic displays and comply with the applicable regulations for repairers of electrical equipment in the Member States where the repairer operates. Reference to an official registration system as professional repairer, where such a system exists in the Member States, shall be accepted as proof of compliance.
2. A professional repairer must have insurance that covers liabilities resulting from repairs, regardless of whether required by the Member State.

RoHS (2002/95/EC) requirements

Applied to all countries that require RoHS.

The RoHS (Restriction of Hazardous Substance in Electrical and Electronic Equipment Directive) is a legal requirement by the EU (European Union) for the global electronics industry sold in the EU and other countries. Any electrical and electronics products launched in the market after June 2006 should meet this RoHS requirement. Products launched in the market before June 2006 are not required to be compliant with RoHS parts. If the original parts are not RoHS complaint, the replacement parts can be non ROHS complaint. If the original parts are RoHS compliant, the replacement parts MUST be RoHS complaint. If product service or maintenance requires replacing parts, confirm the RoHS requirement before replacement.

General descriptions

This manual contains general information. There are two levels of service:

• Level 1: Cosmetic/appearance/alignment service
• Level 2: Circuit board or standard parts replacement

Firmware updates

• Firmware updates for the monitor are available at support.hp.com. If no firmware is posted, the monitor does not need a firmware update.

Before returning the repaired product to the customer

• Perform an AC leakage current check on exposed metallic parts to be sure the product is safe to operate without the potential of electrical shock. Do not use a line isolation transformer during this check.
• Measurements that are not within specified limits present a possible shock hazard. You must check and repair the product before returning it to the customer.

Monitor features

This chapter provides an overview of the monitor’s features.

Features

• Depending on the model, your monitor might include the following features:

Display features

• 86.4 cm, 34-in screen (curved) with 3440 × 1440 resolution, plus full-screen support for lower resolutions; includes custom scaling for maximum image size while preserving original aspect ratio
• Liquid crystal display (LCD) with active matrix and in-plane switching (IPS)
• VA panel technology (select models)
• Wide color gamut to provide coverage of sRGB/DCI-P3 color spaces
• Nonglare panel with an LED backlight
• Wide viewing angle to allow viewing from a sitting or standing position, or moving from side to side
• Tilt, swivel, and height adjustment capabilities
• Pivot capability to rotate the monitor head from landscape to portrait orientation (select models)
• Dual Picture in Picture (PiP) and Picture beside Picture (PbP) functionality to enable the DisplayPort™ and High-Definition Multimedia Interface® (HDMI) inputs to be viewed in each half of the screen (select models)
• On-screen display (OSD) adjustments in several languages for easy setup and screen optimization
• Keyboard Video Mouse (KVM) button for selecting the source device for the monitor (select models)
• Energy saver feature to meet requirements for reduced power consumption
• Cable management feature for placement of cables and cords Connectors
• DisplayPort video input (cable included)
• HDMI video input
• Audio-out (headphone) jack
• USB hub with one USB Type-B port (select models) that connects to the computer (upstream) and two USB ports that connect to USB devices (downstream)
• USB hub with one USB Type-C® port (select models) that connects to the computer (upstream) and two USB ports that connect to USB devices (downstream)
• USB Type-B–to–USB Type-A cable (select models)
• USB Type-C-to-USB Type-C cable (select models)
• HDMI 2.1 cable (select models)
• Plug and Play capability, if supported by your operating system Monitor stand
• Removable stand for flexible monitor head mounting solutions
• HP Quick Release 2 device to attach the monitor head to the stand with a simple click, and then remove it with the convenient sliding tab release
• VESA® mounting bracket for attaching the monitor head to a wall-mount device or swing arm
• VESA mounting capability (100 × 100 mm) for attaching the monitor to a swing arm mount
• Support for a mounting bracket to attach the monitor to a workstation

NOTE: To access the latest user guide, go to http://www.hp.com/support, and follow the instructions to find your product. Then select Manuals.

Rear components

To identify the components on the rear of the monitor, use this illustration and table.

Rear components and their descriptions

computer or game console.
(5)| DisplayPort connector| Connects the DisplayPort cable to a source device such as a computer or game console.
(6)| Audio-out (headphone) jack| Connects optional powered stereo speakers, headphones, earbuds, or a television audio cable.

CAUTION: To reduce the risk of personal injury, adjust the volume before using headphones or earbuds.

---|---|---

Locating the serial number and product number

• Depending on the product, the serial number and product number are located on a label on the rear of or on a label under the front bezel of the monitor head. You might need these numbers when contacting HP for support.

Illustrated parts catalog

To identify the monitor major components, use this illustration and table.

How to order parts

The HP authorized repair center can purchase the power board from HP.

Power board

Description| HP spare part number| Manufacturer part number
---|---|---
PSU OMEN 34c 1st Source| N49788-001| PLPCML492UARC
PSU OMEN 34c 2nd Source| N49788-002| PLPCML492AACQ

Capacitors and connectors are available for purchase from the following EU distributors:

• RS Component: Capacitors | RS Components (rs-online.com)
• Digi-Key: Digikey Electronics
• Farnell: Farnell UK – Electronic Components Distributor

Capacitors by distributor

Component description| Location| Component

distributor

| Distributor part number
---|---|---|---
EC 470uF 20% 25V 10×12 3000 hr 1.6A PY1E| C9117| RS| 25ZLH470MEFC10X12.5
EC 470uF 20% 25V 10×12 5000 hr 1.6A TL1E| C9113/C9114/

C9115/C9116

| Digi-Key| 25YXG470MEFC10X12.5

Connectors by manufacturer

Component description| Location identifier| Component

distributor

| Distributer part number
---|---|---|---
HDMI| CN503| RS| SD-47151-001 (Molex)
HDMI| CN502| RS| SD-47151-001 (Molex)
DisplayPort| CN501| Farnell| DP1RD20JQ1 (JAE)
PHONE JACK| CN601| RS| 913-1021 (RS PRO)

• NOTE: Rear cover and chassis need to be modified to hold connector. Connector may need modifications to meet functional, safety and regulatory requirements accordingly if it doesn’t match exactly.
• NOTE: The connector may need to be modified to meet functionality, regulatory and safety requirements if it is not an exact match.
• You can purchase cables from the HP part store at https://partsurfer.hp.com/Search.aspx.
• Internal and External Power Supplies are available for purchase from the following EU distributor: EET https://www.eetgroup.com/en-eu/
• NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your product, go to https://partsurfer.hp.com/Search.aspx, select your country or region, and then follow the on-screen instructions.

Removal and replacement procedures

Adherence to these procedures and precautions is essential for proper service.

Preparation for disassembly

Use this information to properly prepare to disassemble and reassemble the monitor.

1. Read the “Important safety information” and “Important service information and precautions” sections in the “Getting started” chapter of this guide.
2. Clean the room for disassembly.
3. Identify the disassembly area.
4. Check the position that the monitors are to be placed along with the number of monitors. Prepare the area for material flow according to the disassembly layout.
5. Be sure to have the following equipment and materials:
   • Press fixture
   • Working table
   • Screwdriver
   • Knife
   • Gloves
   • Cleaning cloth
   • ESD protection
   • Scraper bar in the following dimensions:

Rear Cover

Before removing the Rear Cover, follow these steps:

• Prepare the monitor for disassembly. See Preparation for disassembly on page 11.

Remove the Rear Cover

1. Remove the Stand-Base Assy and remove four screw to remove the rear cover.
2. Use your fingers to split the left and right sides apart between the middle frame and rear case.
3. Insert the scraper bar tool into the gap between the middle frame and rear case, and then rotate. The hook opens. Repeat the steps.
4. Insert the scraper bar tool into the gap between the middle frame and rear case, and then rotate. The hook opens. Repeat the steps.
5. Disassemble the Rear Cover and disconnect the connectors. Remove the speakers.
6. Remove the Mylar.
7. Disassemble 7 screws from the boards.
8. Disassemble all the boards from housing.
9. Disconnect all the wires from the board.
10. Remove the screws to remove the Connector board and the key board.

Power board

The power board part number is 1st Source PLPCML492UARC and 2nd Source PLPCML492AACQ.
Before removing the power board, follow these steps:
Prepare the monitor for disassembly. See Preparation for disassembly.

Remove the power board

1. The HP OMEN 34c power board connector position is as follows:
2. Locate the part number location on the board.

Connector repair

• This procedure includes HDMI, DisplayPort and Phone Jack connectors.
• The connectors are on the main board (board part number CBPR2RAHNQ1).

The connector identifiers are as follows:

Before repairing connectors, follow these steps:

• Prepare the monitor for disassembly. See Preparation for disassembly.

IMPORTANT

• Repair Condition: Connector repair is only for out of warranty.
• Repairing must operate by professional repairers (Note) in repair center, not applicable for end user.
• Electrostatic protection is required when component replacement is required.
• The monitor meets ROHS, please use Lead-free solder wire for soldering.
• If Connector need to replace, must check specification and part number whether match the BOM and location.
• If connector need to replace, please insert new parts carefully because the near pin may cause short circuit by inappropriate operate.
• DO NOT allow any liquid on the board. Water and moisture may cause short-circuit to the electronic components and lead to malfunctions.
• The fusion point of Lead-Free solder is requested. Repairing with conventional lead wire may cause damage.
• Work quickly to avoid overheating the circuit board as soon as you confirm the steady soldering condition.
• Keep the soldering iron tip clean and well tinned and when replacing parts.
• A close inspection of the circuit board revealed look in good condition.
• After repaired, must connect source to each port to check Main board function is ordinary.

Note: (The requirement of professional repairers regulation by ERP lot5)

1. The professional repairer has the technical competence to repair electronic displays and complies with the applicable regulations for repairers of electrical equipment in the Member States where it operates. Reference to an official registration system as professional repairer, where such system exists in the Member States concerned, shall be accepted as proof of compliance with this point.
2. The professional repairer is covered by insurance covering liabilities resulting from its activity, regardless of whether this is required by the Member State.

HDMI connector CN503

Repair the HDMI1 connector:

1. Use a soldering iron and a de-soldering pump to remove as much solder as possible from the pin.
2. Use a hot air gun to melt the solder on the pins.
3. Lift the HDMI1 connector from the circuit board.
4. Place the new component on the circuit board. Be sure that it matches the circuit board footprint.
5. Solder the new component.

HDMI 2 connector CN502

Repair the HDMI2 connector:

1. Use a soldering iron and a de-soldering pump to remove as much solder as possible from the pin.
2. Use a hot air gun to melt the solder on the pins.
3. Lift the HDMI2 connector from the circuit board.
4. Place the new component on the circuit board. Be sure that it matches the circuit board footprint.
5. Solder the new component.

DP CN501

Repair the DP connector:

1. Use a soldering iron and a de-soldering pump to remove as much solder as possible from the pin.
2. Use a hot air gun to melt the solder on the pins.
3. Lift the DP connector from the circuit board.
4. Place the new component on the circuit board. Be sure that it matches the circuit board footprint.
5. Solder the new component.

Phone Jack connector CN601

Repair the audio connector

1. Use a soldering iron and a de-soldering pump to remove as much solder as possible from the pin.
2. Lift the audio connector from the circuit board.
3. Place the new component on the circuit board. Be sure that it matches the circuit board footprint.
4. Solder the new component.

Function test

After repair, be sure to confirm that all functions are working.

Table 4-1: Function test

Test item| Operating description| Tool used
HDMI test| Confirm whether image displays and sound plays correctly on the monitor.| Computer or DVD player
DP test| Confirm whether image displays and sound plays correctly on the monitor.| Computer or DVD player
Audio test| Change volume and balance to confirm whether volume is smooth and loud enough.| Speaker

Support and troubleshooting

The following table lists possible issues, the possible cause of each issue, and the recommended solutions.

the power cord.
Monitor is off.| Press the monitor power button.

NOTE: If pressing the power button has no effect, press and hold the power button for 10 sec to disable the Power Button Lockout feature.

 | Video cable is improperly connected.| Connect the video cable properly. For more information, see Connecting the cables.
 | System is in Auto-Sleep Mode.| Press any key on the keyboard or move the mouse to inactivate the screen blanking utility.
 | Video card is incompatible.| Open the OSD menu and select the Input menu. Set Auto- Switch Input to Off and manually select the input.

or

Replace the video card or connect the video cable to one of the computer’s on- board video sources.

Image appears blurred, indistinct, or too dark.| Brightness setting is too low.| Open the OSD menu, and select Brightness to adjust the brightness scale as needed.
“Check Video Cable” is displayed on the screen.| Monitor video cable is disconnected.| Connect the appropriate video signal cable between the computer and monitor. Be sure that the computer power is off while connecting the video cable.
“Input Signal Out of Range” is displayed on screen.| Video resolution and/or refresh rate are set higher than the monitor supports.| Change the settings to a supported setting (see Preset display  resolutions).
The monitor does not enter into a low-power sleep state.| The monitor’s power saving control is disabled.| Open the OSD menu and select Power, select Auto- Sleep Mode, and then set auto-sleep to On.
“OSD Lockout” is displayed.| The monitor’s OSD Lockout function is enabled.| Press and hold the left OSD control button for 10 seconds to disable the OSD Lockout function.
“Power Button Lockout” is displayed.| The monitor’s Power Button Lockout feature is enabled.| Press and hold the Power button for 10 seconds to unlock the power button function.

© Copyright 2023 HP Development Company, L.P.

AMD is a trademark of Advanced Micro Devices, Inc. Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. NVIDIA is a trademark and/or registered trademark of NVIDIA Corporation in the U.S. and other countries. USB Type-C and USB-C are registered trademarks of USB Implementers Forum. DisplayPort and the DisplayPort logo are trademarks owned by the Video Electronics Standards Association (VESA) in the United States and other countries. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

• First Edition: Feb. 2023
• Document Part Number: N31097-OMEN 34c-MSG-V1
• Assembly part number: N31097-001

Product notice

Only trained service personnel familiar with this product should service it. Before performing any maintenance or service, be sure to read “Important Safety Information”.

References

• support.hp.com
• hp.com/support
• HP PartSurfer
• Farnell UK - Electronic Components Distributor
• EGPA350ELL681MK20S Chemi-Con | Capacitors | DigiKey
• EET International

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>