LITETRONICS HBSAS40 High Bay LED Lights Instruction Manual

LITETRONICS HBSAS40 High Bay LED Lights

Product Information

The PIR Sensor Kit (HBSAS40) is designed for use with the Litetronics High Bay SL (HBS Series) LED fixture. It provides multilevel control over occupancy sensing and daylight harvesting functionality. The sensor can be adjusted using a remote control (part number SCR053, sold separately). The default settings include 100% sensitivity, 5-minute hold time, daylight sensor off, 30% dimming level, and 60 minutes dimming time.

What’s Included

• Sensor assembled with mounting bracket
• PM4 10mm screws with washers
• Waterproof wire nuts
• Installation guide

Safety Instructions and Warnings:

The HBSAS40 PIR sensor should be used according to the instructions provided. For any adjustments to the sensor settings, use the remote control (SCR053). Ensure that all power sources are disconnected before installation or maintenance.

OVERVIEW

SAFETY INSTRUCTIONS AND WARNINGS

• When using electrical equipment, basic safety precautions should always be observed
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Installation should only be conducted by a qualified electrician in accordance with NEC and any relevant local building codes.
• Be certain electrical power is OFF before and during installation and maintenance.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.

WHAT COMES IN THE BOX

The following parts are included:

1. (1) Sensor assembled with mounting bracket
2. (2) PM4* 10mm screws with washers and
3. (3) Waterproof wire nuts
4. (1) Installation guide

INSTRUCTIONS

Before installation, carefully remove all parts from the packaging. Inspect product for defects due to shipping.

1. Find the two mouting holes on the side of the fixture
2. Attach the sensor plate to the fixture using the included PM4* 10mm screws and washers. Slide for best positioning, then tighten screws to lock in place.
3. Connect the sensor to the fixture’s 0-10V dimming wires (purple & gray) and 12Vdc wire (black) with the 3 waterproof wires nuts.

The HBSAS40 is a PIR sensor intended for use on Litetronics High Bay SL (HBS Series). It provides multilevel control over occupancy sensing and daylight harvesting functionality. Adjustment to sensor settings can be controlled via remote control, part number SCR053 (sold seperately). See below for the finished look. See back side for sensor functionality

OPERATION

• Warm-up time: After the sensor connects to input power for the first time, the light will display full power for 40 seconds, then revert back to current settings.
• Default settings: 100% sensitivity | 5 min. hold time | Daylight sensor is OFF | Dimming level is 30% | Dimming time is 60 minutes.
• Setting adjustments: When settings are changed via remote control, the fixture will flash ON/OFF to confirm.

SENSOR COVERAGE\

OCCUPANCY SENSING
Occupancy sensor will monitor motion in a space and make automatic adjustments in operation based on set parameters.

• When the space is occupied and regular motion detected, the fixtures maintain at set parameters.
• Once space is empty and no motion is detected, the fixture will maintain the current light level based on set HOLD TIME.
• Once HOLD TIME has elapsed, the fixture can power down completely or dim to a lower level based on set STAND-BY DIM level. The level specified under
  STAND-BY DIM time will continue for set time based on STAND-BY TIME setting, then will power off completely.

DAYLIGHT SENSOR
The built-in photocell will detect the level of ambient light in the space and adjust the fixture output based on set parameters.

REMOTE CONTROL

Settings for the SC005 can be conveniently adjusted using a remote control (part number SCR053).

Settings include:

• Brightness
• Sensitivity
• Hold time
• Daylight harvesting
• Stand-by dimming

The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. Please contact us at 800-860-3392 or via email at customerservice@litetronics.com. For the latest instructions, please visit www.litetronics.com

References

• Commercial Lighting Company | LED Lighting Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>