Kwikset 5053800 Satin Nickel Henley Lever Hall Closet Installation Guide
- June 12, 2024
- Kwikset
Table of Contents
Kwikset 5053800 Satin Nickel Henley Lever Hall Closet Installation Guide
This manual can be used to install a variety of levers.
Please determine your function type prior to installation.
-
Passage (Hall/ Closet)
-
Privacy (Bed/ Bath)
-
Entry (Keyed)
-
Dummy **(Non-Rotating)
**
Tools
*Tools will depend on install type
Adjust the backset of the latch (if needed)
Hold the latch in front of the door hole, with the latch face ush against the
door edge.
If the latch holes are centered in the door hole, no adjustment is required.
Proceed to step 2.
If the latch holes are NOT centered, adjust latch. See “Latch Adjustment”
(step 2C).
Latch Adjustment (only if needed) Move the pin to extend the latch.
Install latch
Door edge chiseled
Door edge NOT chiseled
Remove plates
Install drive-in collar
Use hammer and wood block to tap in latch without damaging it.
Install levers (concealed screws)
Push bolt to install exterior lever.
Keep turn button horizontal as shown.
Install levers (exposed screws)
Option 1: Install privacy/passage levers
IMPORTANT: If installing a passage lock on an entry door, make sure the lever without the screw holes is on the exterior side of the door.
Keep parallel to the door edge.
Privacy locks only
Save the bedroom/bathroom emergency unlock tool for future use.
Option 2: Install entry levers
Note: Locking function may dier per lock/lever.
Option 3: Install dummy (non-rotating) levers
Install strike to door frame
Close door, test latch operation and make adjustments as needed:
If small bolt of latch enters strike hole, reposition strike.
If latch is loose in the strike, adjust the strike tab so it grips the latch
bolt better when the door is closed.
Preparing Your Door
For consumers requiring the door prep template, please visit:
https://images.kwikset.com/is/content/BDHHI/drilling-instructions_knob
Use template to mark holes on door
Select the template that allows you to place the template on the EXTERIOR side
of door. Fold template along fold line and place fold line along the edge of
door. Place centerline approximately 38 in (97 cm) from the oor.
Mark hole on the face of the door. Select desired backset before marking hole.
If there is another hole in the door, or if you are drilling double doors,
make sure to keep the backset consistent
Mark hole on the edge of the door. Select door thickness before marking hole.
Drill holes in door
Drill from one side until the point of drill just breaks through, then
complete hole from the other side to prevent splintering.
Determine which latch will be installed and prepare door edge
Latch with rectangular faceplate
Latch with drive-in collar
If latch is not pre-assembled with desired faceplate, assemble it as shown.
If desired faceplate is not supplied with the latch, please contact Consumer
Support.
Prepare door frame for strike
Locate center of strike hole:
Measure back from door stop, 1/2 thickness of door.
Keep level and trace.
Mark holes (2x)
Register your product at www.kwikset.com/productregistration Rate your product at www.kwikset.com/reviews
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualied locksmith or other security professional.
1-800-327-5625
www.kwikset.com
References
- Door Locks, Door Hardware, Smart Locks & Smartkey Technology | Kwikset
- Register Your Product | Kwikset
- Write a Review of your Kwikset Lock Product for a Chance to Win $250 a Month | Kwikset
- 5061906
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>