LITETRONICS WPC-Series 2-In-1 Traditional or Full Cutoff Wall Pack Instruction Manual

LITETRONICS WPC-Series 2-In-1 Traditional or Full Cutoff Wall Pack

Product Information

The 2-In-1 Traditional or Full Cutoff Wall Pack (WPC-Series) is a lighting fixture designed for outdoor usage. It comes with a pluggable sensor socket, photocell, and EVA cotton pad. The fixture operates at 120V, 240V, and 277V.

What’s Included

• Pluggable sensor socket
• Photocell
• EVA Cotton Pad

Tools Needed

• Phillips Screwdriver or Allen Wrench
• Power Drill

Safety Instructions and Warnings
When using electrical equipment, basic safety precautions should always be observed. Please read the installation instructions carefully and retain them for future reference. The fixture should be installed at a distance of more than 2m from the ground.

Product Usage Instructions

Wall Mount Installation Instructions

1. Turn off power.
2. Use a screwdriver to remove the screws on both sides of the fixture to open it.
3. Pull out the connection terminals and remove the light engine of the fixture.
4. If installing the optional sensor, remove the sensor port plug using a screwdriver.
5. Drill through the mounting hole with an electric drill matching the mounting pattern of the electrical junction box. If installing the optional sensor, refer to the 1-pin sensor socket installation guide for instructions.
6. Attach the EVA cotton pad to the back shell of the fixture.
7. Pass the wire through the back hole of the fixture.
8. Install the back mounting plate onto the mounting seat with screws.
9. Connect the L, N, and G wires to the power supply as per the wiring diagram in Figure 1 and Figure 2.
10. Install the cover of the fixture.
11. Ensure the installation is complete and secure before turning on the power.

Special Functions Instructions
2 IN 1 Controller (Light Engine Selection Switch & CCT Adjustment)

1. Set the LED Selector switch as desired: F for Bottom LED Engine, S for Both LED Light Engines.
2. Select the CCT Color as desired using the CCT Switch. Please turn off the power before adjusting the color temperature.

Wattage Adjustment Instruction
Turn the wattage adjustment knob to the desired wattage selection. The lumen output will change accordingly. Please turn off the power before adjusting the wattage.

For any further assistance or inquiries, please contact Litetronics customer service at CustomerService@Litetronics.com or call 1-800-860-3392.

WHAT COMES IN THE BOX

• Pluggable sensor socket
• Photocell
• EVA Cotton Pad

TOOLS NEEDED

• Phillips Screwdriver or Allen Wrench
• Power Drill

SAFETY INSTRUCTIONS AND WARNINGS

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED. READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

• Litetronics fixtures must be wired in accordance with the National Electrical Code and all applicable local codes.
• Risk of fire or electric shock. 2-In-1 traditional or full cutoff wall pack installation requires knowledge of luminaires’ electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Be certain electrical power is OFF before and during installation and maintenance.
• 2-In-1 traditional or full cutoff wall pack must be connected to a wiring system with an equipment–grounding conductor.
• Make sure the supply voltage is the same as the rated luminaire voltage.
• Only the open holes indicated in the photographs and/or drawings may be made or altered as a result of this kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
• To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or sharp objects.
• Suitable for wet locations.

ATTENTION

1. Please check if there is any damage during shipping. If so, please contact Litetronics customer service.
2. Please read the installation instruction carefully to check whether all the accessories are included.
3. After confirmation, install the fixture according to installation steps.
4. This fixture is available in outdoor usage, the distance from fixture to ground should be more than 2m.

INSTALLATION PROCEDURE

WIRING DIAGRAM

Warning:
During grounding, make sure the ground wire of the driver and fixture housing are connected together with the ground/bonding wire of the local power supply.

WALL MOUNT INSTALLATION INSTRUCTIONS

1. Turn off power.
2. Use a screwdriver to remove the screws on both sides. (Figure 1)
3. Open the fixture, pull out the connection terminals, and remove the light engine of the fixture. (Figure 2)
4. If optional sensor is to be installed, use a screwdriver to remove the sensor port plug. Otherwise, leave sensor port plug in place. (Figure 3)
5. Drill through the mounting hole with an electric drill matching the mounting pattern of the electrical junction box. If optional sensor is to be installed, refer to 1-pin sensor socket installation guide for instructions . (Figure 5)
6. Attach the EV A cotton pad to back shell. (Figure 6)
7. Pass the wire through the back hole. (Figure 7)
8. Install back mounting plate onto the mounting seat with screws. (Figure 8) Follow special functions instructions for light engine selection, CCT and wattage adjustments below. (Figure 13 and Figure 14)
9. Connect L, N and G wires to the power supply as per Figure 1 and Figure 2. (Figure 9)
10. Install the cover of the fixture. (Figure 10)
11. Make sure the installation is complete and secure before turning on the power.

SPECIAL FUNCTIONS INSTRUCTIONS

2 IN 1 CONTROLLER (LIGHT ENGINE SELECTION SWITCH & CCT ADJUSTMENT)

1. Set LED Selector switch as desired:
   • F = Bottom LED Engine
   • S = Both LED Light Engines
2. Select CCT Color as desired using CCT Switch (Figure 13)

Note: Please turn off the power before adjusting the color temperature.

WATTAGE ADJUSTMENT INSTRUCTION
Turn the wattage adjustment knob to desired wattage selection. Lumen output will change to the corresponding wattage.

Note: Please turn off the power before adjusting the wattage.

Thank you for choosing

LITETRONICS

• 6969 W. 73rd Street Bedford Park, IL 60638
• WWW.LITETRONICS.COM
• CustomerService@Litetronics.com
• 1-800-860-3392

The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com.

To check for an updated version of these instructions, please visit www.litetronics.com.

References

• Commercial Lighting Company | LED Lighting Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>