LITETRONICS WPT-Series Slim Wall Pack Instruction Manual
- June 12, 2024
- Litetronics
Table of Contents
LITETRONICS WPT-Series Slim Wall Pack
Product Information
The Slim Wall Pack is a lighting fixture designed for outdoor usage. It comes with a pluggable sensor socket, photocell, and EVA cotton pad for installation convenience. The fixture operates at 120V, 240V, and 277V. It features color adjustable and wattage adjustable functions. The installation procedure includes wiring, wall mount installation, and special functions instructions.
Product Usage Instructions
-
Check for Damage: Before installation, check if there is any damage during shipping. If so, please contact Litetronics customer service.
-
Read Installation Instructions: Carefully read the installation instructions to ensure all accessories are included.
-
Confirm and Install: After confirming all accessories are included, proceed with the installation according to the installation steps.
-
Outdoor Usage: This fixture is suitable for
outdoor usage. Ensure that the distance from the fixture to the ground is more than 2m. -
Turn Off Power: Before starting the installation procedure, turn off the power.
-
Remove Side Screws: Use a screwdriver to remove the screws on both sides of the fixture.
-
Open Fixture and Remove Light Engine: Open the fixture and remove the light engine of the fixture.
-
Drill Mounting Holes: Use an electric drill to drill mounting holes that match the electrical box configuration. Refer to the 1-pin sensor socket installation guide if an optional sensor is to be installed.
-
Attach EVA Cotton Pad: Use a screwdriver to remove the rear plug and attach the EVA cotton pad to the back of the fixture.
-
Install Back Shell: Install the back shell on the mounting seat with screws. Connect the L, N, and G wires to the power supply as per Figure 1 and Figure 2.
-
Reinstall Light Engine: Follow the special functions instructions for CCT (color temperature) and wattage adjustments. Reinstall the light engine and connect it to the fixture back plate.
-
Secure Light Engine: Secure the light engine of the fixture with screws.
-
Complete Installation: Ensure that the installation is complete and secure before turning on the power.
Special Functions Instructions:
Color Adjustable Instruction: Slide the switch to select the desired color temperature (CCT). Remember to turn off the power before adjusting the color temperature.
Wattage Adjustable Instruction: Slide the switch to adjust the desired wattage. Remember to turn off the power before adjusting the wattage.
If you have any questions or need further assistance, please contact Litetronics customer service at 1-800-860-3392 or via email at customerservice@litetronics.com.
Installation Instructions
WHAT COMES IN THE BOX
- Pluggable sensor socket
- Photocell
- EVA Cotton Pad
TOOLS NEEDED
- Phillips Screwdriver or Allen Wrench
- Power Drill
SAFETY INSTRUCTIONS AND WARNINGS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED. READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
- Litetronics fixtures must be wired in accordance with the National Electrical Code and all applicable local codes.
- Risk of fire or electric shock. Slim wall pack installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Be certain electrical power is OFF before and during installation and maintenance.
- Slim wall pack must be connected to a wiring system with an equipment – grounding conductor.
- Make sure the supply voltage is the same as the rated luminaire voltage.
- Only the open holes indicated in the photographs and/or drawings may be made or altered as a result of this kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.
- Suitable for wet locations.
ATTENTION
- Please check if there is any damage during shipping. If so, please contact Litetronics customer service.
- Please read the installation instruction carefully to check whether all the accessories are included.
- After confirmation, install the fixture according to installation steps.
- This fixture is available in outdoor usage, the distance from fixture to ground should be more than 2m.
INSTALLATION PROCEDURE
WIRING DIAGRAM
Warning: During grounding, make sure the ground wire of the driver and fixture housing are connected together with the grounding/bonding wire of the local power supply.
WALL MOUNT INSTALLATION INSTRUCTIONS
- Turn off power.
- Use a screwdriver to remove the screws on both sides. (Figure 1)
- Open the fixture, and remove the light engine of the fixture. (Figure 2)
- Drill mounting holes with an electric drill to match electrical box configuration. If optional sensor is to be installed, refer to 1-pin sensor socket installation guide for instructions. (Figure 3)
- Use a screwdriver to remove rear plug, attach the EVA cotton pad to back. (Figure 5)
- Install the back shell on the mounting seat with screws, Connect the L, N and G wires to the power supply as per Figure 1 and Figure 2. (Figure 6)
- Follow special functions instructions for (CT, wattage adjustments. Reinstall Light Engine and connect to fixture back plate. (Figure 7)
- Secure the light engine of the fixture with screws. (Figure 8)
- Make sure the installation is complete and secure before turning on the power.
SPECIAL FUNCTIONS INSTRUCTIONS
COLOR ADJUSTABLE INSTRUCTION
- Slide the switch to select required (CT. (Figure 12)
Note: Please turn off the power before adjusting the color temperature.
WATTAGE ADJUSTABLE INSTRUCTION
- Slide the switch to adjust desired watts. (Figure 13)
Note: Please turn off the power before adjusting the wattage.
Thank you for choosing
6969 W. 73rd Street Bedford Park, IL 60638
WWW.LITETRONICS.COM
CustomerService@Litetronics.com or
1-800-860-3392
The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com.
To check for an updated version of these instructions, please visit www.litetronics.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>