Q-TRAN SHLD-A Protect LED Strips Instruction Manual
- June 12, 2024
- Q-TRAN
Table of Contents
SHLD-A Protect LED Strips
INSTALLATION INSTRUCTIONS
SHLD-A Protect LED Strips
ATTENTION: Please read all instructions BEFORE installation
- Product to be installed by a licensed electrician
- Always ensure power supply connection to electrical circuit is disconnected before working on it
- Follow diagram to connect Secondary Voltage wires to power supply. Refer to Q-Tran power supply instructions for wiring
- Use only with Class 2 power supply unit — Compatible for use with Q-Tran power supplies
- Suitable for DRY
- Suitable for installation in storage area of a clothes closet when assembled as a finished extrusion up to 4W/ft at Q-Tran facility
- Temp Rating: Refer to cut sheet
- Not rated for walkover
- Diagrams for representation only and not to scale.
METHODS OF INSTALLATION:
MOUNTING METHOD
- SHLD-A (page 3)
- SHLD-B (page 4)
SHLD-A (for standalone use)
SHLD-B (for use within
extrusions)
NOTES:
- Avoid bending in sharp angles which may damage the LED.
- Diagrams for representation only and not to scale.
MOUNTING METHOD: SHLD-A
NOTE: Standalone use
| MATERIALS | SUGGESTED EPOXIES |
|---|---|
| Concrete, Stone, Cinderblock, Metal, and Brick | Loctite Metal and Concrete |
Two-Part Epoxy
ABS, Fiberglass, Plastic, and PVC| Loctite Plastic Two-Part Epoxy
Tile, Wood, Ceramic, Glass, or Metal| Loctite Clear Two-Part Epoxy
All Purpose| Strong Stik
Temperature and environmental
concerns:
- Ideal application environment is 70-100ºF in 50% humidity or less.
- Minimum application temperature: 50ºF
- This temperature and humidity should be maintained for 72 hours after application for maximum bond strength.
For porous materials (Wood, Brick, Concrete etc.) apply two
layers of paint or primer to the surface. This will help create a better
bonding surface for these materials. These can be purchased from a local
hardware store.
a. Clean surface.
b. Measure PVC carrier and cut to length.
c. Remove adhesive backing on carrier and mount to surface.
a.
Mount LED within guideline on PVC Carrier and apply pressure. Start and end
LED 3/8″ from end of carrier.
b. Install Shield Lens. Start at input feed wire end. Remove adhesive backing
and provide pressure as you mount down the lenght of carrier.
c. Cut shield to desired length. Use scissors or razor blade.
Allow 3/8″ of dead space at each end.
MOUNTING METHOD: SHLD-B
NOTE: In ExtrusionsTemperature and environmental
concerns:
- Ideal application environment is 70-100ºF in 50% humidity or less.
- Minimum application temperature: 50ºF
- This temperature and humidity should be maintained for 72 hours after application for maximum bond strength.
Using a 50/50 alcohol mix, thoroughly clean surface area of the
extrusion and tray. Allow 5 minutes to dry.
Refer to extrusion installation instructions for cutting to length at
https://www.q-tran.com/products/extrusions/
Peel back 0.5″ of the VHB
tape’s protective film on one end of LED and use firm pressure to adhere it to
the extrusion, avoiding air bubbles. Continue peeling the film and adhering
the strip in small sections until the entire length is installed.
Peel back 0.5″ of the VHB tape’s protective film on both ends of
the shield lens and use firm pressure to adhere it to the extrusion along the
sides of the LED strip, avoiding air bubbles.
Continue peeling the film and adhering the shield lens in small sections until
the entire length is installed.
For instructions pertaining to the installation of extrusion components, visit
the applicable extrusion product page at q-tran.com.
© 2023 Q-Tran Inc. All rights reserved
155 Hill St. Milford, CT 06460 |
203-367-8777
sales@q-tran.com
www.q-tran.com
Specification subject to change.
Rev-04-11-23
Documents / Resources
|
Q-TRAN SHLD-A Protect LED
Strips
[pdf] Instruction Manual
SHLD-A, SHLD-B, SHLD-A Protect LED Strips, SHLD-A, Protect LED Strips, LED
Strips
---|---
References
- LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran
- Your Name as Your Email | Hover Realnames
- LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran
- LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran
- LED Profiles | LED Extrusions | Aluminum Extrusion | Q-Tran
- SHIELD Engineered to Protect LED Strips | Q-Tran
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>