Q-TRAN Flexible Fixtures-Nexus Flexible LED Strip Lighting Instruction Manual
- June 12, 2024
- Q-TRAN
Table of Contents
FLEXIBLE FIXTURES – NEXUS
INSTALLATION INSTRUCTIONS
Flexible Fixtures-Nexus Flexible LED Strip Lighting
ATTENTION : Please read all instructions BEFORE installation
- Product to be installed by a licensed electrician – Field modifications void warranty
- Use only with Class 2 power supply unit — Compatible for use with Q-Tran power supplies
- Surface mount
- Not rated for walkover
- Input Voltage: 24VDC
- Diagrams for representation only and not to scale.
METHODS OF INSTALLATION
Mounting Method
- VHB (page 6)
- WSC (page 7)
| Cove, Under & over cabinet:
Ideal for office, retail, hospitality, education, laboratory, and
residential.
---|---
| Shelf :
Ideal for office, retail, hospitality, education, laboratory, and
residential.
| Display cabinet :
Ideal for retail and hospitality.
| Signage :
Ideal for lobby, retail, hospitality, institutional, and transportation.
COMPONENTS & HARDWARE
MOUNTING CLIP & MOUNTING
CHANNEL| ADHESIVE SOLD SEPARATELY
---|---
WSC| VHB TAPE
White snug clip
| |
TAPE-VHB-IP20
NOTES:
MOUNTING CLIP
- 2 white snug clips provided per first 12”, 1 for each additional 12”.
Other mounting styles incur additional charge, see price guide for details
CONTINUOUS WIRING CONFIGURATION OPTIONS
Review wire method to ensure
clean installation prior to mounting finished fixture.
NOTE: Additional wire methods include:
S1: Connector/Wire Input only
P1: Connector/Wire Input and Output
SURFACE MOUNTING METHOD
SURFACE PREPARATION
Temperature and environmental concerns:
- Ideal application environment is 70-100ºF in 50% humidity or less.
- Minimum application temperature: 50ºF
- This temperature and humidity should be maintained for 72 hours after application for maximum holding force.
Using a 50/50 alcohol mix, thoroughly clean the backside of
the fixture and the surface area where fixture will be installed.
Allow 5 minutes to dry. 
For porous materials (Wood, Brick, Concrete
etc.) apply two layers of paint or primer to the surface. This will help
create a better bonding surface for these materials. This can be purchased
from local hardware store.
MATERIALS|
SUGGESTED EPDXIES
---|---
Concrete, Stone, Cinderblock, Metal, and Brick| Loctite Metal and Concrete
Two-Part Epoxy
ABS, Fiberglass, Plastic, and PVC| Loctite Plastic Two-Part Epoxy
Tile, Wood, Ceramic, Glass, or Metal| Loctite Clear Two-Part Epoxy
All Purpose| Strong Stik
SURFACE MOUNTING METHOD: VHB ADHESIVE MOUNT
BEFORE installation, the surface must be thoroughly cleaned and dried for
maximum bond strength. (Page 5)
Determine the fixture(s)
location and positioning on desired surface before adhering fixture to
surface. Make any necessary reference markings to indicate extrusion
placement.
- To adhere the VHB adhesive, peel the white film back while evenly applying the tape to the mounting side of the extrusion. The red side should be visible.
- Remove the red film and position extrusion in place according to your previous reference marking(s).
Remove protective film from
the surface of the extrusion’s lens.
NOTES: EPOXY ALTERNATIVE: For improved bonding strength, apply a small amount of epoxy at each end. Refer to table on for suggested epoxies. These can be purchased at a local hardware store. Please follow all manufacturer instructions for suggested epoxy. page 5
SURFACE MOUNTING METHOD: WHITE SNUG CLIP
- 2 clips provided per first 12”, 1 for each additional 12”
Determine the
fixture(s) location and positioning on desired surface; evenly distribute
clips. Make any necessary reference markings to indicate where each clip is to
be secured in place. Recommended every 12”.
- Secure clips using the #4 flat head hardware provided
- Ensure the screw head is flush with the clip’s base.
NOTE: Flat head screw type is dependent on surface/application material
Alternative flat head screws may be required. Refer to the surface material
manufacturer for suggested screw type.
Snap fixture onto clips.
© 2023 Q-Tran Inc. All rights reserved
155 Hill St. Milford, CT 06460 |
203-367-8777
sales@q-tran.com
www.q-tran.com
Specification subject to change.
Rev-07-13-23
Documents / Resources
|
Q-TRAN Flexible Fixtures-Nexus Flexible LED Strip
Lighting
[pdf] Instruction Manual
Flexible Fixtures-Nexus Flexible LED Strip Lighting, Flexible Fixtures-Nexus,
Flexible LED Strip Lighting, LED Strip Lighting, Strip Lighting
---|---
References
- Your Name as Your Email | Hover Realnames
- LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran
- BOXA | BOXA™ | Q-Tran
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>