Pablo 120-240V Bola Felt Pendant Lamp Instruction Manual

Pablo 120-240V Bola Felt Pendant Lamp Instruction Manual

BOLA FELT PENDANT

120/240V ASSEMBLY & INSTALLATION INSTRUCTIONS

**CORD PATH DIAGRAM

**

1. a SECURE DRIVER TO MOUNT BRACKET WITH PROVIDED TAPE.

b SECURE MOUNT BRACKET TO JUNCTION
BOX OR CEILING USING APPROPRIATE ANCHOR METHODS

IMPORTANT! BE SURE TO REFERENCE CORD PATH DIAGRAM BEFORE MOVING ON.

2. BE SURE TO WEAVE CORD THROUGH ALL NECESSARY PARTS LISTED ABOVE BASED ON LAMP MODEL.
   a BEND WIRE ENDS BEFORE PASSING THROUGH STRAIN RELIEF.
   
   b PASS CORD THROUGH STRAIN RELIEF AND SET LAMP HEIGHT BY FASTENING BOTH (TOP AND SIDE) SET SCREWS. (IF NECESSARY: TRIM EXCESS CORD)
   

3. PLACE FASTENED STRAIN RELIEF ONTO MOUNTING BRACKET. (NOTE! STRAIN RELIEF SHOULD NEST INTO RECESS IN BRACKET SURFACE)
   

4. WIRE DRIVER TO BUILDING (US : BLACK TO BLACK/WHITE TO WHITE) (EU: BLACK TO BROWN/WHITE TO BLUE)
   
   NOTE: PURPLE AND GREY WIRES ARE USED ONLY IN 0-10V INSTALLATIONS

5. WIRE DRIVER TO LAMP (RED TO RED/BLUE TO BLACK)
   

6. SECURE CANOPY COVER TO BRACKET ASSEMBLY WITH CANOPY NUT. TIGHTEN UNTIL FIRMLY IN PLACE.
   

MULTI-LIGHT CANOPY 9” and 12”

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. LOCATE BUILDING POWER FEED/JUNCTION BOX
   DETERMINE AND MARK SWAG LOCATIONS REFERENCING THE DIAGRAM AND PROVIDED CHART. PROVIDED LAMP WIRES ARE 8.9’, LAMP HANG HEIGHT REDUCES IN RELATION TO SWAG DISTANCE FROM CANOPY.
   

SWAG SPACING CENTER TO CENTER| BOLA DISC 12| BOLA DISC 18| BOLA DISC 22| BOLA DISC 32
---|---|---|---|---
BOLA DISC 12| 5” 12.7 CM| 8” 20.3 CM| 9” 23 CM| 13” 33 CM
BOLA DISC 18| 8” 20.3 CM| 8” 20.3 CM| 9” 22.9 CM| 13” 33 CM
BOLA DISC 22| 9” 23 CM| 9” 23 CM| 9” 23 CM| 13” 33 CM
BOLA DISC 32| 13” 33 CM| 13” 33 CM| 13” 33 CM| 13” 33 CM
2. REMOVE CANOPY COVER, SET ASIDE 3. REMOVE CANOPY COVER, SET ASIDE

4. REMOVE DRIVER PLATE BY REMOVING 4 3X FLAT HEAD SCREWS
   

5. ROUTE BUILDING WIRING THROUGH MOUNTING PLATE.
   

6. ATTACH PLATE TO JUNCTION BOX WITH 8-32 MACHINE SCREWS
   (NOT PROVIDED) OR APPROPRIATE ANCHORS.

7. WIRE BUILDING WIRING TO TERMINAL BLOCK. 7 US: BLACK TO BLACK AND WHITE TO WHITE EU: BLUE TO WHITE AND BROWN TO BLACK.
   

8. REMOVE THREADED SWAG CAP
   

9. MOUNT SWAG USING APPROPRIATE FASTENER AND ANCHOR IN MARKED LOCATION
   
   NOTE: Cable slot should face canopy center point
   
   
   USE PROVIDED GLOVES WHEN HANDLING LAMP TO AVOID FINGER MARKS.

10. LACE WIRE IN SWAG. MAKE SURE WIRE IS IN CHANNEL.

11. THREAD SWAG CAP INTO SWAG TO SECURE LAMP. THIS STEP IS WHERE YOU DETERMINE YOUR LAMP HANG HEIGHT.
    

12. THREAD WIRE THROUGH MOUNT PLATE.

13. PULL WIRE THROUGH AND STRAIN RELIEVE
    
    NOTE: STEP 14 APPLIES ONLY TO THE 9” CANOPY ONLY

14. REMOVE PLUG
    A
    
    B PLACE CANOPY COVER BAG OVER CANOPY
    
    C USING A PENCIL, PUNCTURE SMALL HOLE FOR WIRE TO PASS THROUGH
    
    D THREAD WIRE THROUGH CANOPY AND CENTER OF DRIVER PLATE
    E STRAIN RELIEVE WIRE ON DRIVER PLATE.
    THIS IS WHEN YOU SET YOUR HANG HEIGHT
    F TIE KNOT JUST PAST STRAIN RELIEF
    

15. ATTACH DRIVER PLATE TO MOUNT PLATE WITH PROVIDED FLAT HEAD SCREWS THREAD WIRES THROUGH CENTER OF DRIVER PLATE
    

16. REMOVE INDIVIDUAL LAMP DRIVERS FROM INDIVIDUAL LAMP CANOPIES

PEEL LINER OFF OF VHB TAPE AND 16 ATTACH DRIVERS TO DRIVER PLATE

17. CONNECT DRIVERS TO TERMINAL BLOCK.
    US: BLACK TO BLACK AND WHITE TO WHITE
    EU: BROWN TO BROWN AND BLUE TO BLUE
    
    
    IF USING 0 – 10V DIMMING WIRE DIMMER IN PARALLEL
    

18. ONE AT A TIME, WIRE LAMPS TO MATCHING
    DRIVERS. CUT EXCESS WIRES IF NECESSARY
    

19. ATTACH CANOPY COVER CARE INSTRUCTIONS
    WIPE CLEAN WITH A SOFT DAMP CLOTH AVOID AMMONIA BASED CLEANER.
    
    USE PROVIDED GLOVES WHEN HANDLING LAMP TO AVOID FINGER MARKS.

20. THREAD GLOBE ONTO HEAT SINK
    CARE INSTRUCTIONS
    WIPE CLEAN WITH A SOFT DAMP CLOTH AVOID AMMONIA BASED CLEANER.
    

Customer Support

INFO@PABLODESIGNS.COM
888 MARIN STREET
SAN FRANCISCO, CA
94124
PABLODESIGNS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>