FREEDOM 73020613 Emblem Vinyl Fence Gate Kit Instruction Manual

: June 12, 2024
: FREEDOM

Table of Contents

FREEDOM 73020613 Emblem Vinyl Fence Gate Kit
Tools/Materials Needed:

FREEDOM 73020613 Emblem Vinyl Fence Gate Kit

Product Information

Product Name: Emblem Vinyl Fence Gate Kit
Model Number: 34117713
Revision: 1.23
Manufacturer: Freedom Product

Warning
It is important to read all instructions prior to installing the product. Always refer to the manufacturer’s safety instructions when operating any tools.

Notice
Vinyl gate posts require an internal support system for weight-bearing purposes, therefore a post stiffener is required. The post stiffener needs to be purchased separately.

Emblem Gate Component List

Boards* (6 boards for 4′ kit, 8 boards for 5′ kit)
U-Channels
Top Rail
Bottom Rail
Gate Uprights
Upright Caps
Screws
Vinyl Cement
Hinges
Latch Plate
Gate Stop

Tools/Materials Needed:

Phillips Screwdriver
Safety Glasses
Line Level
Tape Measure
Drill
2 Square Drive Bit
2 Wood Blocks
3/32 Bit Square Pencil

Warranty
To obtain and review a copy of the warranty, please visit Freedomproduct.com/warranty. You may also contact us at 1-888-418-4400 or email CS.outdoorliving@ebarrette.com.

Product Usage Instructions
Step 1:
Apply vinyl cement to all inside surfaces of the first upright
where the rails will be inserted.

Step 2:
Insert both rails into one upright assembly.

Step 3

Place the U-channels on the end boards, then slide the boards into rails, locking them together.
Apply vinyl cement to all inside surfaces of the second upright where rails will be inserted.
Attach the remaining upright assembly to the rails, making sure the boards fit snugly.

Step 4
Measure diagonally from the top of the left corner rail (A) to the bottom of the right corner rail (B) and note the length. Then, measure diagonally from the top of the right corner rail (C) to the bottom of the left corner rail (D). Note the length. Make sure both measurements are the same before installing screws into the uprights.

Step 5
Install two 6 screws (provided) through each upright insert and into the rail using the molded grooves on the insert as a guide.

Step 6
Install upright caps onto the top of each upright with provided vinyl cement.

Step 7
Check the included hardware kits for instructions or visit barretteoutdoorliving.com to obtain a copy.

Read all instructions prior to installing the product. Refer to the manufacturer’s safety instructions when operating any tools.

WARNING:

Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling, and assembling the product.
Incorrect installation may cause harm to the product or individual.
Not pool code approved.

NOTICE:

DO NOT attempt to assemble the kit if parts are missing or damaged.
DO NOT return the product to the store, for assistance or replacement parts call: 1-888-418-4400.

BEFORE YOU BEGIN
Vinyl gate posts require an internal support system for weight-bearing purposes therefore a post stiffener is required. Post stiffener needs to be purchased separately. Post-stiffener appearance may vary

TOOLS/MATERIALS NEEDED

| Phillips Screwdriver
---|---
| Safety Glasses
| Line Level
| Tape Measure
| Drill
| #2 Square Drive Bit
| 2″ Wood Blocks
| 3⁄32″ Bit
| Square
| Pencil

Emblem Gate Component list:

Description

Boards*
U-Channels
Top Rail
Bottom Rail
Gate Uprights
Upright Caps
Screws
Vinyl Cement
Hinges
Latch Plate
Gate Stop

FREEDOM-73020613-Emblem-Vinyl-Fence-Gate-Kit-fig-2

To obtain and review a copy of the warranty please visit Freedomproduct.com/warranty. You may also contact us at 1-888-418-4400 or email CS.outdoorliving@ebarrette.com.

Apply vinyl cement to all inside surfaces of the first upright where the rails will be inserted (Fig. 1).
Insert both rails into one upright assembly (Fig. 2).
- Place the U-channels on the end boards, then slide the boards into rails, locking them together (Fig. 3).
- Apply vinyl cement to all inside surfaces of the second upright where rails will be inserted.
- Attach the remaining upright assembly to the rails making sure the boards fit snugly.
Measure diagonally from top of left corner rail (A) to the bottom of right corner rail (B) and note the length. Then, measure diagonally from top of right corner rail (C) to the bottom of left corner rail (D). Note the length. Make sure both measurements are the same before installing screws into the uprights (Fig. 4).
Install two 6″ screws (provided) through each upright insert and into the rail using the molded grooves on the insert as a guide (Fig. 5).
Install upright caps onto the top of each upright with provided vinyl cement (Fig. 6).
Check the included hardware kits for instructions or visit barretteoutdoorliving.com to obtain a copy.