lorelli V 3.1 Viovla Set Baby Stroller Instruction Manual

lorelli V 3.1 Viovla Set Baby Stroller

N-Scan the QR code to get more product information and manual instruction in more languages. Download QR Scanner App onto your device.

IMPORTANT – READ CAREFULLY AND KEEP FOR FUTURE REFERENCE!

SAFETY REQUIREMENT

1. This baby stroller is appropriate for children weighing up to 22 kg or at age up to 4 years whichever occurs first! Seat: Age 6+ months
2. The height of the carried child in the stroller should not exceed 104 cm!
3. Use parking device if you do not hold the stroller with hand!
4. Do not leave the stroller on hills or inclined surfaces even if you have activated the parking system!
5. Parking device shall be engaged when placing and removing the children!
6. The shopping basket can take a maximum load of 2 kg!
7. Any load attached to the handle and/or on the back of the backrest and/or on the sides of the vehicle will affect the stability of the vehicle! Maximum load of the accessory bag 1 kg. Do not hand any additional bags !
8. Regularly check for loose parts! Make routine inspection, regularly maintain, clean and/or wash the vehicle!
9. The vehicle shall be used only for 1 child!
10. Accessories which are not approved by the manufacturer shall not be used!
11. Only spare parts delivered or recommended by the manufacturer/ distributor can be used!
12. Always use the restraint system! Always use the crotch belt in combination with the waist belt! To prevent injury from a fall or a slip off always use the shoulder straps!
13. Make sure that the safety belts are placed properly!
14. The stroller should always be used under the supervision of an adult!
15. Do not allow children to suspend him/herself or play in the stroller!
16. Do not allow children to stand in the stroller!
17. Do not allow your child to stand on the seat and foot rest!
18. Do not use the stroller on uneven surfaces near fire or other dangerous places!
19. Do not use the stroller on stairs and escalators!
20. Fold the stroller before go upstairs and downstairs. Mounting the stroller on stairs, pavements and others with the child in it and by pushing the handle causes deformation of the stroller and is out warranty repair!
21. Adjusting of the back rest must be made only by a person read carefully the instruction rules for adjusting!
22. Any additional baggage left in the stroller may cause it to become unstable!
23. The person who assembles the stroller must be familiarized with its functions!
24. WARNING! Use only the mattress/pad sold with this stroller. Do not add any additional mattresses unless the recommended one by the manufacturer!
25. WARNING! For children under 6 months, please place the mattress/pad above the belts . Picture 32;33. WARNING! Start using the safety belts immediately after your child is capable of sitting without external assistance!
26. The front bar can not be used as a carry handle.
27. Car seat is compatible with the stroller „Viola“ !
28. When using the car seat: This vehicle does not replace a cot or a bed. Should your child need to sleep, then it should be placed in a suitable pram body, cot or bed.

WARNING

1. WARNING! Never leave the child unattended!
2. WARNING! Ensure that all the locking devices are engaged before use!
3. WARNING! To avoid injury ensure that the child is kept away when unfolding and folding this product!
4. WARNING! Do not let the child play with this product!
5. WARNING! This pushchair is designed to be used from baby’s birth. You shall use the most reclined position for newborn babies. The newborn child is not able to sit and hold his/her head up unassisted. Therefore do not fix the backrest in sitting position for children under 6 months!
6. WARNING! Always use the restraint system!
7. WARNING! Check that the pram body or seat unit or car seat attachment devices are correctly engaged before use
8. WARNING! This product is not suitable for running or skating!
9. WARNING! Keep away from fire !
10. WARNING! Images on the title page and in the instruction manual are only illustrative and may differ from the real product.
11. WARNING! The seat is not appropriate for children less than 6 months!
12. WARNING! The carry-cot is appropriate for a baby that cannot seat without help, cannot turn down, and cannot raise on its arms and knees. Maximum child’s weight: 9 kg

MAINTENANCE AND CARE

1. To clean the metal parts, wipe with a moist and then dry towel until the stroller is all dry.
2. To clean the plastic parts, use a towel, water and a soft detergent.
3. To clean the textile parts, use a solution for cleaning tapestries.
4. When not in use, never place other objects in or on the stroller! This will damage it!
5. Always dry and air the stroller if it is not dry enough!
6. Run regular clean-ups over the wheel axes and the plastic elements.
7. Always clean the wheel axes and plastic elements after using the pram over sandy or dusty surfaces!
8. DO NOT LUBRICATE the wheel axes or other movable parts of the stroller! Just clean them!
9. Run regular checks for loose or damaged parts and if there are such, immediately replace them with new ones!

PARTS

1. Stroller’s chassis – 1 pc.
2. Shopping basket – 1 pc.
3. Rear wheels – 2 pcs.
4. Front wheels – 2 pcs.
5. Transforming seat (carry-cot) – 1 pc.
6. Bumper bar -1 pc.
7. Canopy – 1 pc.
8. Leg cover for a seat (carry-cot) – 1 pc.
9. Bag for accessories -1 pc.
10. Child safety seat -1 pc.
11. Seat adapters – 2 pcs.
12. Pad – 1 pc.

UNFOLDING

1. Folded stroller (Photo 2)
2. Release the locking mechanism Raise the handlebar upwards and forward and the stroller will be unfolded and locked automatically. (Photo 3;4)

ASSEMBLING

1. Install the front wheel by pressing them upward until they are locked. (Photo 5) Check for proper locking. For dismounting press the button on the console and pull the wheel downwards. (Photo 6)
2. Assemble the rear wheels as shown in photo 7. For dismounting press the button on the rear axle and pull the wheel. (Photo 8)
3. Install the carry-cot by taking care that the camps are placed and fixed in the designated holes of the chassis.(Photo 11) Clicking means that the carry-cot is fixed. For disassembly, simultaneously press the side buttons of the carry-cot and pull it upwards (Photo 12). The seat transformed into a carry-cot for a newborn must always face the parent (photo 15).
4. Install the bumper bar for the child. (Photo 10) To remove the bumper bar, press the side buttons and pull it.
5. Fasten the zipper of the canopy to the carry-cot (Photo 9).
6. The carry-cot is transformed into a seat by fixing the belts located on the reverse part of the seat and the legs (Photos 16/26). Carry-cot adjustment – Turn the carry-cot into a sitting position by pressing simultaneously the side buttons. After positioning of the carry-cot (the seat), fix the hook against rocking (photo 17, 18) Attention: Always release the hook before carry-cot adjustment.
   Damage of the carry-cot adjustment mechanism due to incorrect operation is not covered by the guarantee.

EXPLOITATION

1. To fix the stroller in place, use the brake of the rear wheels by pressing backward the braking pedal located on the rear axle. To release the brake, press the braking pedal forward (photo 31).
   Attention! The brake does not guarantee optimal stopping on steep slopes! Therefore, do not leave the stroller on a slope with a child that sits or lies in it! WARNING! The brake of your stroller is a kind of parking device. To activate the brake, please note that the stroller shall not move. Carefully press the brake pedal and at the same time mildly push the stroller forward- backward to synchronize the operation of the braking device and for more secure activation of the braking mechanism.

2. You can adjust the handlebar by pressing simultaneously the two side buttons of the mechanism and turning upwards or downwards.

3. When the stroller moves on rough and uneven surfaces, use the option for straightforward movement by pressing the locking pin of the front wheels downwards (photo 21). To release the front wheels, raise the locking pin.

4. To change the canopy position, hold the upper part and pull it down or up to the desired position (photo 13/14).

5. Backrest adjustment – to raise the backrest, press the button on the buckle behind the backrest and pull the belt. To release the backrest, press the button of the buckle and release the backrest down (photo 19).

6. When using the seat, IT IS A MUST to place the safety belts for the child!

7. Attach the shoulder and the abdominal belts and fix them in the central buckle to lock them (photo 20). Adjust the length of the safety belts by pulling the buckles (photo 21). To unlock the belts, push the button on the central buckle (photo 22). For babies under 6 months, pass the belts through the straps (photo 23).

FOLDING

1. Activate the brakes of the stroller.

2. Stroller folding:
   Variant 1 – if the seat is installed in the direction of movement (photo 26), the stroller is folded together with the seat without dismounting it. Simultaneously push the big round side buttons of the seat and raise and then fold the canopy as shown in photo 26. Press simultaneously the small round buttons and fold the lower part of the seat upwards to the canopy as shown in photo 27. Pull the mechanisms from both sides of the handlebar and push downwards (photo 28). The correctly folded stroller shall look like the one in photo 29. Lock the chassis (photo 30).

3. Variant 2 – if the seat (carry-cot) is installed opposite the direction of movement, the stroller is folded after dismounting the seat (the carry-cot) – photo 15. First, remove the seat (carry-cot) from the chassis via the two semicircular side buttons located on both sides – photo 12. Then pull the mechanisms located on both sides of the handlebar and push downwards until the chassis is fully folded. Lock the chassis (photo 30).

CAR SEAT “Group 0+” / newborn and weighing up to 13 kg. /

NOTICE

1.  This is a ‘Universal’ child restraint. It is approved to Regulation No 44, 04 series of amendments, for general use in vehicles and it will fit most, but not all, car seats.
2. A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable of accepting a ‘Universal’ child restraint for this age group.
3. This child restraint has been classified as ‘Universal’ under more stringent conditions than those applied to earlier designs that do not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.

Appropriate only if the approved vehicles are equipped with three-point / retractor safety belts approved in accordance with UNECE Regulation № 16 or other equivalent standards.

EXTREMELY DANGEROUS! Do not place the rear-facing child seat on the front seat with the airbag. Death or serious injury can occur.

Important safety instructions!

Please read the instructions carefully, because improper installation may cause serious injury, in this case, the manufacturer is not responsible.

1. WARNING! The car seat can not be used forward facing!

2. WARNING! The rigid items and plastic parts of a child restraint shall be so located and installed that
   they are not liable, during everyday use of the vehicle, to become trapped by a movable seat or in a door of the vehicle. Prevent harness/vehicle belt from getting trapped between car doors or rubbing against sharp parts of the seat or body.

3. WARNING! All straps holding the restraint to the vehicle should be tight, all straps restraining the child should be adjusted to the child’s body. The straps should not be twisted! Always make sure that the booster
   seat harness and vehicle belt are correctly tensioned to ensure maximum protection for your child.

4. WARNING! The device should be changed when it has been subject to violent stresses in an accident. After an accident, replace your child restraint and the vehicle seat belts. Although they may look undamaged, they may not protect your child as well as they should.

5. WARNING! Follow closely the instructions for installation. Failure can result in injury to the child!

6. WARNING! It is dangerous to make any alterations or additions to the device without the approval of the Type Approval Authority. Your child is in danger if you don’t follow closely the installation instructions provided by the child restraint manufacturer.

7. WARNING! Do not use any load bearing contact points other than those described in the instructions and marked in the child restrained. Ensure the vehicle seat belt buckle is connected to the correct main load bearing contact point which is intended for the occupied vehicle seat. Ensure the buckle and the seat belt of the vehicle do not interfere with the main load bearing contact points of the child restrained system. Ensure you are following the correct way path of the vehicle’s safety belt by the installation of the restrained system and by the restraining of the child. On this way you will avoid an unsatisfactory position of the adult safety belt buckle relative to the main load bearing contact points on the restraint. Please contact the child restraint manufacturer if in doubt about this point.

8. WARNING! Rearward child restraint systems should not be used in seats protected by an airbag.

9. WARNING! NEVER leave your child unattended in the safety device, even for the shortest time!

10. WARNING! Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.

11. WARNING! Do not use the child restraint system without the cover.

12. WARNING! Do not replace the seat cover with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the restraint performance.

13. WARNING: DO NOT attempt to dismantle, modify or add to any part of the booster car seat or change the way your vehicle seat belts are made or used.

14. WARNING! Do not leave the buckle in a partially closed position and it must only lock when all parts are engaged. It must be possible to release the child from the restraint immediately in an emergency.

15. WARNING! Install the child restraint in vehicle seating positions categorized as ‘Universal’ in the vehicle owner’s manual, by using the primary belt route.

16. WARNING! If the chair is not provided with a textile cover, keep it away from sunlight, otherwise it may be too hot for the child’s skin. If the vehicle has been left in the sun for a long time, check the seat cover and make sure it is not too hot before placing the child in the child cushion.

17. WARNING! Do not use the car seat in the house. It is not designed for home use and should only be used in the vehicle!

18. WARNING! Periodically check the belts for wear, paying special attention to the points of attachment, protections and regulating devices. If the harness / vehicles belts becomes cut or frayed, replace it before traveling.

19. WARNING: ALWAYS secure your child with the safety belts when using the car seat.

20. WARNING! Do not leave the buckle in a partially closed position and it must only lock when all parts are engaged. It must be possible to release the child from the restraint immediately in an emergency. Your child must be taught never to play with the buckle. The buckle is NOT CHILD PROOF

21. WARNING! The baby seat must be secured with car safety belt, even when it is not in use.
    An unsecured seat may injure other passengers in the car in an urgent stop.

22. WARNING! Store this child seat in a safe place when it is not being used. Avoid placing heavy objects on top of it. Do not allow your child seat to come into contact with corrosive substances e.g. battery acid.

23. WARNING! Do not leave your child in this safety seat for a long period of time. By longtrips make more breaks and take out the child from the safety seat.

24. WARNING! Security is only guaranteed if the child restraint is fitted in accordance with these instructions.

25. WARNING! The instruction must be retained on the child restraint for its life period

WASHING INSTRUCTIONS

1. The car seat can be cleaned using lukewarm water and soap. Do not use aggressive cleaners like abrasives or thinner.
2. The cover should be washed by hand at a maximum temperature of 30oC. Do not put in the dryer, just air it.
3. The plastic parts can be cleaned by using a wettish drapery. Please, do not use any solvate.

TYPES OF APPROVED BELTS TO HAVE IN THE CAR
Your child seat can be installed ONLY with the help of 3-point belts!!! ONLY in the OPPOSITE direction of movement of the car!

• Possibility to install ONLY on seats with 3-point seat belts!

CAN NOT BE USED FOR SEATS with 2-point belt!

Parts

1. Carrying handle
2. Belt softener
3. Belt buckles
4. Strap for belts adjustment
5. Button for adjusting the belt (under the cover)
6. Lap belt guide
7. Red button for handle adjusting
8. Diagonal belt guide
9. Openings for shoulder straps
10. Shoulder straps
11. Buckle Pads
12. Head Pillow
13. Upholstery
14. Canopy
15. Leg cover

Check the height of the shoulder belts

Always check that the shoulder belts are placed at the correct height for your child. Select the height of the straps according to the child’s height. The position of the straps should be at or slightly above the shoulders of the child. Warning: Do not place the straps too high or so that the child can lean on them! In the back of the safety seat , there are 2 pairs of holes , which can be used to adjust the shoulder straps to suit your child’s weight (Fig. 2)

Adjusting the height of seat belts

1. Press the button for belts adjusting “5” and at the same time pull both shoulder straps. (Picture 3)
2. Take out the belts “10″ of the holes on the back from the front of the seat.
3. Place back the belts in the desired holes on the front side of the backrest and connect them behind the back with the adjusting strap “4″. Make sure the straps are placed on the same level and are not twisted.

Fastening the seat belt

1. Combine the two pieces “E”and “F” at the end of the belt (Picture 6) and place them in the central buckle “3” until it clicks into place. (Picture 7)
2. Make sure the belt is locked by pulling the shoulder straps up. (Picture 8)
3. To release belt, press down the red button on the central buckle “3”.

Adjusting the length of the belts

1. Slack the belts: Press the button for belts adjusting “5” and at the same time pull both shoulder straps.(Picture 3)
2. Tightening the belt: Place your child in the seat, fasten both belts in the buckle in the center and pull the strap “4″ in the middle of the seat. (Picture 5)

Removing the upholstery Picture 19
For children weighing up to 10 kg, the car seat should be used with a padded liner. When the child’s weight is between 10 kg and 13 kg, you must remove the padded liner. Release the straps from the buckle and remove the padded liner.

Crotch belt adjustment
The crotch belt is positioned at the inner slot of the car seat. Once when you feel that the crotch belt is too tight for your child, please adjust as follow :

1. Pull up the cover at the front of your car seat. Picture 9
2. Lift the metal part on the end of the belt , rotate and goes through the openings to pull out the belt. Picture 9 a;b;c;d
3. Insert the metal part through the outer slot, then under the bottom and through the inner slot. Place the metal part at horizontal position and pull the belt to ensure that it is secure. Picture 9 e;f;g

Adjusting of the carry handle
The carry handle of the car seat can be adjusted in 3 stable positions. To adjust the handle, please press the red button on the handle on both sides at the same time. Now it can be rotated. (Picture 10)

1. Position – Straight up for carrying. (Picture 11)
2. Position – The handle clicked back to initiate the rocking feature. (Picture 12)
3. Position – Down to support baby for feeding. (Picture 13)

Ensure that the handle is locked in a position,the harness is correctly fitted and the buckle is fastened before carrying your car seat.

INSTALLATION OF SEAT
“Group 0 +” / newborn and weighing up to 13 kg. / Please use 3-point safety belts of the car to ensure the safety of the child and to secure the child’s seat! Your child seat can be installed ONLY with the help of 3-point belts!!! ONLY in the OPPOSITE direction of movement of the car!

• Step 1. Adjust the handle to the upright position. (Picture14)
• Step 2. Place the child’s safety seat on the car seat „opposite the direction of movement“ and ensure that it is firmly placed to the backrest. The child safety seat must be used only on the rear seats of the car!
• Step 3. Slide the lap belt of the vehicle’s 3-point seatbelt through both Lap belt guides. (Picture 15) Let the tongue plate snap in the belt lock with a clearly audible ”click”. (Picture 16) Pull the shoulder belt in the arrow direction to tighten the lap belt. Check to make sure the tongue plate is locked by pulling on the belt.
• Step 4. Place the diagonal belt in the diagonal belt guide at the back of the seat (Picture 17)
• Step 5. Tighten the vehicle’s own 3-point seatbelt by pulling hard on the positions. (Picture 18)
• Step 6. Make sure that the belt is not twisted and strongly tightened. Make sure the seat is fixed firmly on the car seat.
• Step 7. Place the child in the seat. Check the height of the shoulder belts. Make sure the straps are not twisted or hanging somewhere. Fasten the seat belts on the child, making sure that they are well placed, and pull the strap in the center of the seat to tighten.

INSTALLING THE CAR SEAT ON THE STROLLER FRAME

WARNING The child safety seat must always face the parents, as shown in Fig. 20.

Installation – hold the child’s safety seat so that it faces the stroller’s handlebar. Place the adapters of the child safety seat (included in the set Photo 1, position 11). Position the adapters of the child safety seat above the holes of the plastic holders on both sides of the chassis and press down until a click is heard. Pull upwards the child safety seat to ensure that it is firmly fixed to the stroller’s chassis.

Disassembly – simultaneously press the buttons from both sides of the adapters and pull upwards the seat from the stroller’s chassis. You can dismount the adapters from the seat by pushing simultaneously the red side buttons (figure 20).

Didis Ltd.
Bulgaria, Shumen, 6 Trakia-iztok Street Phone: +359 54 850 830 e-mails: home.market@didis-ltd.com; export@didis- ltd.com

Unic importator in Romania
DIDIS INTERNATIONAL Strada Sfantul Pantelimon Nr.1 Oras Pantelimon, Judetul Ilfov Phone: +40 21 211 65 60 Fax: +40 21 210 65 62 E-mail: office@didis.ro

• www.lorelli.eu

References

• Lorellishop | Anne ve Bebek Ürünleri
• Lorelli - Baby and children products with proven quality

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>