FiiO V01 DAC and Headphone Amplifier User Guide

FiiO V01 DAC and Headphone Amplifier

Buttons and Ports Labeled

1. 3.5mm headphone out/SPDIF out
2. 4.4mm BAL headphones out
3. Gain switch
4. Power/Volume knob
5. RGB ambient light
6. USB Type-C port
7. Power indicator light

Operation Instruction

1. Turn on/off
   Rotate the Power/Volume knob clockwise until a click sound is heard to turn on the device; keep rotating clockwise to increase the volume. Rotate the Power/Volume knob anticlockwise to decrease the volume; keep rotating anticlockwise until a click sound is heard to turn off the device.
   Note: Technically, channel imbalances may occur if the volume is adjusted within low levels by the potentiometer knob. When listening at a low volume level, it is suggested to set the Gain level to Low, and turn the knob past 9 o’clock.

2. Gain switch
   When switched to the H position, the Qll will run under the High Gain mode. When switched to the L position, the Qll will run under the Low Gain mode.

3. RGB ambient light
   When turning off the device, the RGB ambient light is off. When turning on the device, the RGB ambient light will be constantly on. Different colors stand for different states. Here are the details.

   • A) The Qll is powering on but not in working state: Light blue
   • B) In USB decoding mode:
   • PCM,;;48kHz: Light blue
   • PCM >48kHz: Yellow
   • All to DSD: Green
     Note: The RGB ambient light can be turned off in the FiiO Control App on an Android device.

4. USB sound card mode

   • A) On WindowslO and above systems, the Qll runs driver-free.
   • B) After installing the USB DAC driver, the Qll will support ASIO mode for a better experience. Download link for USB DAC driver: https://www.jadeaudio.com/supports
   • C) For MAC computers, there is no need to install the USB DAC driver, so directly select the Qll as the output device.

5. SPDIF output mode
   The Qll supports SPDIF output. Use an exclusive 3.5mm headphone out to SPDIF adapter cable, plugging the 3.5mm end into the 3.5mm headphone out/SPDIF output port of the Qll and the SPDIF end into a device that supports SPDIF input to transmit digital audio signals.

6. Power ambient light

7. A) Powering on/Standby/Working: Blue light will be constantly on.

8. B) Low battery: Blue light will keep flashing. Please charge the Qll in time.

9. C) Charging (device is off): Red light will be constantly on, and will be off when the charge is full.

10. D) Charging (device is on): Purple light will be constantly on. When the charge is full, Blue light will be constantly on.

11. Accessory using instructions

    • A) When using the included Type-C to Type-C cable orType-C to Lightning cable to connect the Qll to a mobile device for decoding, it will only consume little current power of the mobile device, which means the mobile device will not provide power for the Qll.
      ( Note: When connecting the Qll to a device that limits the current output, like mobile phones, tablets, etc, please use the cable included in the accessory. Do not use other unauthorized cables, which may consume the power of the mobile device and cause output overload.)

    • B) Use the included USB-A to Type-C cable to connect the Qll to a computer for data transmission and charging.

    • C) The silicone strap and anti-skid feet can be used to bind the Qll and the mobile device.

Notes and Precautions

• You might be unable to hear the sound of the surroundings when wearing headphones. For your safety, please avoid using headphones in dangerous situations.
• Please adjust the volume to a suitable level before wearing headphones to protect your hearing.
• Please do not place the device in circumstances of excessive high/low temperatures (above 45°C or below 0°c).
• Please keep the device away from liquids, so to avoid any damage to it.
• Please charge the battery on a regular basis to secure the battery life if this product has not been used for a long time.
• Please do not disassemble, damage the battery, or drop it into fire. It’s prohibited to continue using the battery if it is soaked in water.

List of Items Included

• (please check if the following items are included) USB-A to Type-C data cable
• Type-C to Lightning data cable
• Type-C to Type-C data cable
• Silicon strap
• Silicon anti-skid feet
• Warranty card
• Quick start guide

To Learn More
For related video instructions of the Qll and FAQ (Frequently Asked Questions), please scan the QR code below. To learn more about the product, please visit ou rwebsite: http://www.fiio.com.

• jadeaudio.com
• fiio.com

Due to continuous improvement, every specification and design is subject to change at any time without further notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>