VISUAL COMFORT S 2204 Halle 30 Inch Vanity Light Instruction Manual

VISUAL COMFORT S 2204 Halle 30 Inch Vanity Light

Product Information

• The Halle 30 Vanity Light, item # S 2204, is a light fixture designed for installation in bathrooms or vanity areas. It is not included with bulbs. The fixture should be installed in accordance with all applicable local installation codes and by a person familiar with its construction and operation.
• The package should be carefully inspected for any damage or defects before installation. All packaging material should be retained until installation is complete and approved.

Tools required for installation (not included) are:

• Phillips Screwdriver
• Hammer
• Slotted Screwdriver
• Drill
• Pencil

Product Usage Instructions

1. Remove all parts from the box and place them on a clean, soft surface.
2. Remove the mounting plate (B) from the fixture body (G) by unscrewing the side screws (F).
3. Remove the lantern (I) from the fixture body (G) by unscrewing the side screws (H).
4. Using the mounting plate (B) as a guide, align it with the junction box and mark the anchor positions.
5. Drill holes in the marked positions using a drill bit slightly smaller than the anchor size.
6. Install anchors (A) into the drilled holes using a hammer.
7. Attach the mounting plate (B) to the junction box and secure it with mounting screws (D). Then secure wood screws (C) to the anchors (A).
8. Wrap the fixture ground wire (green) around the green grounding screw in the junction box.
9. Install the fixture body (G) to the mounting plate (B) and secure it with side screws (F).
10. Install a light bulb into the socket.
11. Install the lantern (I) to the fixture body (G) and secure it with side screws (H).

Care Instructions

To clean the vanity light, use only a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS

Halle 30″ Vanity Light
Item # S 2204

NOTICE:

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED

(NOT INCLUDED):

• Phillips Screwdriver
• Slotted Screwdriver
• Drill
• Hammer
• Pencil

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from fixture body (G) by removing side screws (F).
3. Remove lantern (I) from fixture body (G) by removing side screws (H).
4. Using mounting plate (B) as a guide, line up with the junction box and mark anchor positions.
5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into holes using hammer.
6. Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).
7. Wrap fixture ground wire (green) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (E).
   • NOTE: It is imperative that the fixture is grounded.
8. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (E).
9. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (E).
   • CAUTION: Do not reverse the hot and neutral connections.
10. Make sure all wire connections are tight, then carefully tuck into the junction box.
    • NOTICE:
    • This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.
11. Install fixture body (G) to mounting plate (B) and secure with side screws (F).
12. Install a light bulb into the socket.
13. Install lantern (I) to fixture body (G) and secure with side screws (H).

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>