DOMADOO IOMZB-110 IO Module Installation Guide

: June 8, 2024
: DOMADOO

Table of Contents

Product description
Disclaimers
Precautions
Connecting to wired device
Getting started
Modes
Read User Manual Online (PDF format)
Download This Manual (PDF format)

IO Module

DOMADOO IOMZB 110 IO Module-

INSTALLATION MANUAL
Version 1.7

Product description

With the 10 Module, you can connect wired devices to a Zigbee network. Providing four inputs and two outputs, the 10 Module works as a bridge between wired devices and a control system over Zigbee networks. Its inputs can be configured as IAS alarm inputs. making the 10 Module suitable for use in alarm systems.

Disclaimers

CAUTION:

Choking hazard! Keep away from children. Contains small parts.
Please follow the guidelines thoroughly. The 10 Module is a preventive, informing device. not a guarantee or insurance that sufficient warning or protection will be provided. or that no property damage, theft, injury. or any similar situation will take place. Domadoo products cannot be held responsible in case any of the above-mentioned situations occur.

Precautions

WARNING: For safety reasons, always disconnect the IO Module from the powersocket before removing the front cover.
Do not remove the product label as it contains important information.
Do not open the IO Module.
Do not paint the device.

Placement
Connect the IO Module to a device that is located at a temperature between 0-50°C.

Connecting to wired device

You can connect the 10 Module to different wired devices: doorbells. window blinds, wired security devices, heat pumps and more.
The connection of the different devices follows the same principle, using the different inputs and outputs:
a.

IN1
IN2
IN3
IN4
NC2
COM2
NO2
NC1
COM1
NO1
5-28 Vd.c.
USB
PWR
RST
LED| Inputs with internal Pull Up. Must be
shorted to IO Module GND for signal
IO Module GND
Normally Closed for Relay Output 2
Common for Relay Output 2
Normally Open for Relay Output 2
Normally Closed for Relay Output 1
Common for Relay Output 1
Normally Open for Relay Output 1
Power Supply
NOTE: Use ”5-28 V” or ”USB PWR”.
If both are connected ”5-28V” is the primary Power Supply.
Power Supply
NOTE: USB PWR is then used as fall back in case ”5-28 V” is disconnected.
Reset
User Feedback
---|---

Getting started

When the device is connected and powered up, the 10 Module will start searching (up to 15 minutes) for a Zigbee network to join. While the 10 Module is searching for a Zigbee network to join, the yellow LED flashes.
Make sure that the Zigbee network is open for joining devices and will accept the 10 Module.
When the LED stops flashing, the device has successfully joined the Zigbee network.
If the scanning has timed out, a short press on the reset button will restart it.
b.

Resetting
Resetting is needed if you want to connect your IO Module to another gateway or if you need to perform a factory reset to avoid abnormal behavior.
STEPS FOR RESETTING

Connect the IO Module to a power outlet.
Press and hold the reset button with a pen (see Illustration b).
While you are holding the button down, the yellow LED first flashes once, then two times in a row, and finally numerous times in a row.
c.
Release the button while the LED is flashing numerous times in a row.
After you release the button, the LED shows one long flash, and the reset is completed.

Modes

SEARCHING GATEWAY MODE
The yellow LED flashes.
Fault finding and cleaning

In case of a bad or wireless weak signal. change the location of the 10 Module. Otherwise. you can relocate your gateway or strengthen the signal with a smart plug
If the search for a gateway has timed out. a short press on the button will restart it

Disposal
Dispose the product property at the end of its live. This is electronic waste which should be recycled.
FCC statement
Changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced redo/ TV technician for help.

This device complies with FCC PF radiation exposure bmits set forth for an uncontrolled environment The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions I This device may not cause harmful interfer-ence. and 2 this device must accept any interference received. ncludng interference that may cause undesired operation.
This device contans licence-exempt transrntterfst/receiverts) that comply with Innovation. Science and Economic Development Canada’s licence-exempt PSS(s) Operation is subject to the following two conditions
1 This devce may not cause interference
2 This device must accept any interference including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

ISED statement
Innovation, Science and Economic Development
Canada ICES-003 Compliance Label:
CAN ICES-3 (B)/NMB-3(B).
CE certification
The CE mark affixed to this product confirms its compliance with the European Directives which apply to the product and, in particular, its compliance with the harmonized standards and specifications.

IN ACCORDANCE WITH THE DIRECTIVES