CHRISTOPEIT TM 650 Treadmill Instruction Manual

HEIMSPORT-TRAININGSGERÄT
ELEKTRISCHES LAUFBAND Assembly and exercise instructions
for Order No. 2035

TM 650 Treadmill

Dear customer,
We congratulate you on your purchase of this home training sports unit and hope that we will have a great deal of pleasure with it. Please take heed of the enclosed notes and instructions and follow them closely concerning assembly and use.
Please do not hesitate to contact us at any time if you should have any questions.
Top-Sports Gilles GmbH
Friedrichstraße 55
42551 Velbert

Important Recommendations and Safety Instructions

Our products are all TÜV-GS tested and therefore represent the highest current safety standards. However, this fact does not make it unnecessary to observe the following principles strictly.

1. Assembly the machine exactly as described in the installation instructions and use only the enclosed, specific parts of the machine contained in the assembly. Before assembling, verify the completeness of the delivery against the delivery notice and the completeness of the carton against the parts list in the installation and operating instructions.

2. Check the firm seating off all screws, nuts and other connections before using the machine for the first time and at regular intervals (every 1-2 months) to ensure that the trainer is in a safe condition. Replace defective components immediately and/or keep the equipment put of the use until repair.

3. Set up the machine in a dry, level place and protect it from moisture and water. Uneven parts of the floor must be compensated by suitable measures and by the provided adjustable parts of the machine if such are installed. Ensure that no contact occurs with moisture or water.

4. Place a suitable base (e.g. rubber mat, wooden board etc.) beneath the machine if the area of the machine must be specially protected against indentations, dirt etc.

5. Before beginning training, remove all objects within a radius of 2 metres from the machine.

6. Do not use aggressive cleaning agents to clean the machine and employ only the supplied tools or suitable tools of your own to assemble the machine and for any necessary repairs. Remove drops of sweat from the machine immediately after finishing training.

7. WARNING! Systems of the heart frequency supervision can be inexact. Excessive training can lead to serious health damage or to the death. Consult a doctor before beginning a planned training programme. He can define the maximum exertion (pulse, Watts, duration of training etc.) to which you may expose yourself and can give you precise information on the correct posture during training, the targets of your training and your diet. Never train after eating large meals.

8. Only train on the machine when it is in correct working order. Use original spare parts only for any necessary repairs. WARNING: Replace the worm parts immediately and keep this equipment out of use until repaired.

9. When setting the adjustable parts, observe the correct position and the marked, maximum setting positions and ensure that the newly adjusted position is correctly secured. Please remove the Tools you need to adjust after adjusting a new position.

10. Unless otherwise described in the instructions, the machine must only be used for training by one person at a time. The exercise time should not overtake 60 min./daily.

11. Wear training clothes and shoes which are suitable for fitness training with the machine. Your clothes must be such that they cannot catch during training due to their shape (e.g. length). Your training shoes should be appropriate for the trainer, must support your feet firmly and must have non-slip soles.

12. WARNING! If you notice a feeling of dizziness, sickness, chest pain or other abnormal symptoms, stop training and consult a doctor.

13. Never forget that sports machines are not toys. They must therefore only be used according to their purpose and by suitably informed and instructed persons.

14. People such as children, invalids and handicapped persons should only use the machine in the presence of another person who can give aid and advice. Take suitable measures to ensure that children never use the machine without supervision.

15. Ensure that the person conducting training and other people never move or hold any parts of their body into the vicinity of moving parts.

16. At the end of its life span this product is not allowed to dispose over the normal household waste, but it must be given to an assembly point for the recycling of electric and electronic components. You may find the symbol on the product, on the instructions or on the packing.
    The materials are reusable in accordance with their marking. With the re-use, the material utilization or the protection of our environment. Please ask the local administration for the responsible disposal place.

17. To protect the environment, do not dispose of the packaging materials, used batteries or parts of the machine as household waste. Put these in the appropriate collection bins or bring them to a suitable collection point.

18. The maximum permissible load (=body weight) is specified as 120 kg. Evaluate your body weight before you starting the exercise.

19. If the connecting cable of this item is damaged, this must be replaced by the manufacturer or the customer service or with an electrically certified person.

20. Declaration of Conformity
    Manufacturer: Top-Sports Gilles GmbH, Friedrichstraße 55, D-42551 Velbert. This product conforms to the following european directives and standards: 2014/30/EU (EMC), 2014/35/EU (LVD), 2011/65/EG (RoHS) and EN 20957-1 (Homesport).

21. The assembly and operating instructions is part of the product. If selling or passing to another person the documentation must be provided with the product.

Assembly Instructions

Put everything clearly on the ground and control the completeness based on the assembly steps. Attention: The simplified assembly process requires 100% attention. Especially in the crease and folding positions. Assembly time is approx. 20min.
Step 1:

1. Remove all small parts, loose packing material out of the box and then take out with help of a second person the preassembled frame of packaging.
2. Lift the support tubes (3+4) high enough so that you can fold down the computer with handrail. Screw the computer (35) to the support tubes (3+4) using the screws M8x15 (51) and washers (64).

Step 2:

1. Fold up with care the supports left and right (3+4) and tighten the supports left and right (3+4) with screws M8x15 (51), screws M8x45 (70) and washers (64) at base frame (2).
2. Attach the support covers left and right (59+60) to cover up the connection points and secure with screw 4×20 (19).
3. Remove the protective film from the display if present.
4. Insert the smartphone / tablet holder (37) into the computer (35).
   

Step 3:
Checks and How to start

1. Check the correct installation and function of all screwed and plug connections.
2. When everything is in order, connect the power supply cable (31) with wall power (220-240V~50-60Hz) and switch on the main switch (32) below the front frame.
3. Put the safety key (71) onto the computer (35) and the computer will show normal manual mode. Put the safety clip (71) at your exercising cloth and stand on the side rails (20). Press Start-Button and after a Count Down the treadmill start moving. Start walking onto the walk surface (26) when speed is slowly and follow the speed. Familiarize yourself with the machine at a low speed settings.
4. Run in the middle of the running surface (26) and don’t step on the side foot rails (21), Hold yourself tight at handrail (5) if you feel insecure Only run with look at the Computer (35) on the treadmill during the running. In emergency case, step of the treadmill lateral and hold on to the handle (5).

Note: Please keep the tool set and the instructions in a safe place as these may be required for repairs or spare parts orders becoming necessary later. Incline adjustment:
Raise the running frame by hand and fold the treadmill together until it is arrested. Pull out both security pins (20), shift the incline adjuster (19) in another position and use the security pins (20) again for secure the new position. The treadmill can folded down.
The incline adjustment is intended in addition to raise the load of the mountain accrual.
How to move/store your treadmill:

1. Put one hand at the end caps of the running frame and lift up into vertically position that it automatically locks the upright position.
2. Place your hands on top of the handrails, than lean the machine toward your body until it is easy moveable on transportation rollers (21).
3. Hold with one hand the position of running frame and press with  footagainst the secure position at cylinder (11) sothat the running  frame can drop down on the floor.

Warning:
Before folding up the treadmill switch off and wait until the running surface totally stopped.
Don’t start the treadmill in fold up position!

Maintenance and adjusting

1. Lubrication for the running belt:
   In order to keep the machine in the best condition, please add some Silicone oil between the running belt and the running board after 50 hours or 1 to 2 month of use. But the running belt may slip, if you lubricate too much. To lubricate the belt please pull the walking belt up and injection the silicone oil into the gap between belt and walking deck.![CHRISTOPEIT TM 650 Treadmill

• fig 5](https://manuals.plus/wp-content/uploads/2023/07/CHRISTOPEIT-TM-650 -Treadmill-fig-5.jpg)

  2. Adjusting running belt:
     You need to adjust the walking belt to the normal position, per the following steps if it is off.
     1. Set speed at 3-5km.
     2. Using the Allen wrench for running belt adjustment (12) to adjust the belt tension bolt on the end cap of the system frame.
     3. If you want to move the belt towards left, turn the right tension bolt clockwise.
     4. If you want to move the belt towards right, turn the left tension bolt clockwise.
     5. If you have already done according to the steps above and it is still not at the good range, then the running belt should be damaged already, please contact your local dealer for replacement.
     Note: Make sure that the running surface is as centered as possible. Once these moves too far from the center, (about 10 mm) it should be readjusted into the center.

  3. Running belt slips:
     1. Make sure the walking belt is not too loose.
     2. Make sure the motor belt is not too loose.

  4. No light on the Display:
     1. Check if the power plug is properly connected.
     2. Check if the safety key on the computer is in place.
     3. Check if the wire in the right post is properly connected.
     Remind ! Before you inspect any wire or electrician part, please ensure that the Power supply has been turned off.

  5. Abnormal noise from the machine
     1. Check if any screw of machine is loose.
     2. Check if the motor belt is off.
     3. Check if the running belt is off.

Note: Please contact your local dealer if you have checked all the above listed things but the problem is still there.

User manual of Computer

Displays:
ENTFERNUNG (DISTANCE) – Display:
Shows the distance you run in kilometers.
KCAL / PULS
shows the approx. consumed kilocalories in KCAL and the heart rate in alternation every 6 seconds.
ZEIT (TIME) – Display:
Shows the time of exercising in minutes.
GESCHWINDIGKEIT (SPEED) – Display :
Shows the speed of the treadmill in kilometers per hour.
Key-Function:
[START]-Key:
Press this key to start exercise program (motor starts running).
[STOP/PAUSE]- Key:
Press this key during exercise to interrupt the program (motor stops running). Within 5 min. you can press [START]-key again to continue this exercise program or press [STOP]-key again to finish this program. Prevalues can set to zero by pressing the [STOP] –
key.
[EINGABE] -Key (ENTER):
Select key of Time-program, Distance-program or Calories-program.
[PROG.]-Key (Programs):
Press this key to select exercising programs P1- P15.
[+]-Key:
Press speed up -key increase settings or motor speed.
[-]-Key:
Press speed down -key decrease settings or motor speed.
Quick Speed -keys 4 and 8 km/h
Press one of these keys and the speed changes direct into 4 or 8
Remote keys:
The functions can be activated using the remote keys on the handles Start/Stop and +/- can be controlled in the same way as on keys at computer.
Manual
How to start manual mode:
Put in the AC plug in wall power 220V-240V, 50HZ-60HZ and put on the power switch. Put safety clip on to the computer and it will show normal manual mode. Stand your feet on both side rails. Put the safety key at you exercise cloth and press [START]-key to start with exercising. After a 3 sec. count down, the mo tor begin to run slowly and you can step on the running belt and follow the speed. Adjust the speed with [+/-]- keys into desired speed. If put off the safety clip from computer at any time, the motor stop slowly and the display will show „—“. After put on the safety key on computer the normal manually program will show. Press [+/-] key to adjust value of speed. Press quick speed key to adjust speed quickly. All values of the displays will counter up.
Time-Program:
Press the [EINGABE]-key once and the time display lights up. [ZEIT/PULS] -Display shows a suggestion of 30:00 minutes. Press [+/-]-key to set value. The range is: 5:00-99:00min. If set a value the display counts up till zero and then stops running motor.
Distance-Program:
Press the [EINGABE]-key until the distance lights up. [DISTANCE/CAL] Display shows a suggestion of 1:00 km/h. Press [+/-]-key to set value. The range is: 0,50- 99:90KM. If set a value the display counts up till zero and then stops running motor.
Calories-Program:
Press the [EINGABE]-key until the KCAL lights up. [DISTANCE/CAL] Display shows a suggestion of 50,0 kcal. Press [+/-]-key to set value. The range is: 10-990 kcal. If set a value the display counts up till zero and then stops running motor.
Exercise programs P1-P15:
On the normal manual mode, press the [PROG.]-key to choose one of the exercise speed programs P1-P15. Each program is divided into 20 intervals of time and the speed changes as following program list shows. Initial setting time is 30min, set a time for training session and press [START]key to start the program. Pressing [STOP]-key to have a break or finish earlier the program. Press [+/-] -key to adjust speed during the program if it is too quick or slow. With next intervals of time the speed level will change back to program mode. If the program runs till end of time the motor will stop running

↓
Program| Time →| Programs in 20 intervals of time
---|---|---
1| 2| 3| 4| 5| 6| 7| 8| 9| 10| 11| 12| 13| 14| 15| 16| 17| 18| 19| 20
P01| Km/h| 2| 3| 3| 4| 5| 3| 4| 5| 5| 3| 4| 5| 4| 4| 4| 2| 3| 3| 5| 3
P02| Km/h| 2| 4| 4| 5| 6| 4| 6| 6| 6| 4| 5| 6| 4| 4| 4| 2| 2| 5| 4| 2
P03| Km/h| 2| 4| 4| 6| 6| 4| 7| 7| 7| 4| 7| 7| 4| 4| 4| 2| 4| 5| 3| 2
PO4| Km/h| 3| 5| 5| 6| 7| 7| 5| 7| 7| 8| 8| 5| 9| 5| 5| 6| 6| 4| 4| 3
P05| Km/h| 2| 4| 4| 5| 6| 7| 7| 5| 6| 7| 8| 8| 5| 4| 3| 3| 6| 5| 4| 2
P06| Km/h| 2| 4| 4| 4| 5| 6| 8| 8| 6| 7| 8| 8| 6| 4| 4| 2| 5| 4| 3| 2
P07| Km/h| 2| 3| 3| 3| 4| 5| 3| 4| 5| 3| 4| 5| 3| 3| 3| 6| 6| 5| 3| 3
P08| Km/h| 2| 3| 3| 6| 7| 7| 4| 6| 7| 4| 6| 7| 4| 4| 4| 2| 3| 4| 4| 2
P09| Km/h| 2| 4| 4| 7| 7| 4| 7| 8| 4| 8| 9| 9| 4| 4| 4| 5| 6| 3| 3| 2
P10| Km/h| 2| 4| 5| 6| 7| 5| 4| 6| 8| 8| 6| 6| 5| 4| 4| 2| 4| 4| 3| 3
Pll| Km/h| 2| 5| 8| 10| 7| 7| 10| 10| 7| 7| 10| 10| 5| 5| 9| 9| 5| 5| 4| 3
P12| Km/h| 3| 4| 9| 9| 5| 9| 5| 8| 5| 9| 7| 5| 5| 7| 9| 9| 5| 7| 6| 3
P13| Km/h| 3| 6| 7| 5| 9| 9| 7| 5| 5| 7| 9| 5| 8| 5| 9| 5| 9| 9| 4| 3
P14| Km/h| 2| 2| 4| 5| 6| 5| 4| 3| 2| 1| 2| 3| 4| 5| 6| 5| 4| 3| 2| 1
P15| Km/h| 2| 4| 6| 8| 6| 6| 4| 4| 2| 2| 2| 4| 6| 8| 6| 6| 4| 4| 2| 2

Body fat measurement / BMI
Use the PROG. -key to select body fat measurement (FAT) after the 15 training programs and a -1- appears for gender. Select your gender 0 = male or 1 = female by pressing the +/- keys. Press the EINGABE -key again and -2- appears one after the other for age, -3- for height, -4- for weight and enter your personal data using the +/- buttons. All data have been entered and confirmed with the EINGABE -key. With -5- the request appears to grip the hand pulse sensors with both hands for 5 seconds so that the measurement can be carried out. Then the Body fat displayed as a BMI value.
BMI <19 = underweight, BMI 19-26 = normal weight,
BMI 26-30 = overweight, BMI> 30 = obese
Pulse Rate:
A metal contact plate, the sensors, is embedded in the left and right handles. Please make sure that both palms are always resting on the sensors with normal force. The hand pulse measurement is only for orientation, as movement, friction, sweat, etc. can lead to deviations from the actual pulse. A few people may experience malfunctions in the hand pulse measurement. If you have difficulties with the hand pulse measurement, we recommend you the use of a cardio chest strap with an external heart rate monitor. So-called cardio pulse monitors are commercially available, which consist of a transmitter chest strap and a wristwatch receiver.
Safety clip
The safety clip has an emergency function. In fear or danger or if you fall down or jumped from it, the safety clip will lose position at computer and stops the motor with break system. Put the safety key out from computer on any status, the display is „- – -“, the buzzer beeps each second. Put the safety key on computer, then the display will enter normal manual mode. All parameter reset to zero.
Hibernation
If the treadmill is not in use the display switch off into Standby Mode. INDOOR TRAININGS APP
The product can be used with the Kinomap app. This enables entertaining and interactive training with Android or IOS devices and saving training data.
Sport, coaching, gaming and eSport are the keywords of the Kinomap app. This contains many kilometers of real film material to exercise inside as if you were outside; Tracking routes and analysis of your performance; Coaching content; Multiplayer mode; new posts daily; Official indoor races and more … The APP thus contains approx. 100,000 videos recorded by athletes and 200,000 km of accumulated tracks for cycling, running or rowing for currently approx. 270,000 members from all over the world.
Download the app and connect
Scan the adjacent QR code with your smartphone / tablet or use the search function at the Playstore (Android) or APP Store (IOS) to download the Kinomap APP. Register and follow the instructions in the APP.
Activate Bluetooth on the smartphone or tablet and select the device manager via the menu in the APP and then select the „treadmill“ category. Then select your type designation via the manufacturer logo „Christopeit Sport“ in order to connect the sports equipment. Depending on the sports equipment, different functions are recorded by the APP via Bluetooth or data is exchanged.
Attention: The Kinomap APP offers a free trial version for 14 days. After that, fees will apply which are listed on the Kinomap homepage. Further information can be found at: https://www.kinomap.com/en/

https://eqrcode.co/a/PRiGN9

Meanings of error message codes
In case of malfunctions may adjoining list of error messages help for savvy people to get function back. Basically, electrical repairs only in compliance with the relevant safety rules which exists. For more information and assistance in case of malfunctions with our service department (contact details see last page.)

2.Change the safety clip or safety clip socket at computer.
3.If it’s still not ok, than change the computer.
E01| Communication abnormality: abnormal communication between the controller and the electronic meter after powering on.| 1.Switch off the treadmill and plug out AC cable.
2.Check each section of communication cables from the electronic meter to the controller and ensure that all cables are well connected.
3.Check whether cables between the electronic meter and the controller are damaged; if yes, replace the damaged wire.
E02| Voltage-proof protection:| 1.Switch off the treadmill and plug out AC cable
2.Check whether the power supply voltage is less than 50% of the normal value. Please ensurecorrect voltage and test again.
3.Check whether the controller emits the odor of burning; if yes, replace the controller.
4.Check whether motor cables are well connected; re-connect motor wires.
E03| No sensor signal:| 1.Switch off the treadmill and plug out AC cable.
2.Check whether the sensor cable is well plugged or whether it is damaged; plug it well or replace the sensor.
E05| Over-current protection:| 1.Check whether power supply voltage specifications is inconsistent or too low and use correct voltage specifications for re-test.
2.System self-protection is triggered under excessive current caused by the excessive load more than the rated value, or some place of the treadmill is jammed so that the motor cannot rotate; thus, the system start up self- protection against excessive current under excessive load; adjust the treadmill and restart it.
3.Check whether there is over-current sound or burning odor when the motor is running; replace the motor.
4.Check whether the controller emits abnormal odor; replace it if yes.
E07/E08| EEPROM defect| Replace the control board.
Motor will not start| The motor cable is damaged or connected incorrectly.
The fuse on the control board has been damaged or dropped.
The control board is defect.
The motor is defect.| Check the motor cable.
Check the fuse. Reinsert it, or replace the fuse.
Replace the control board. Replace the motor.

Training instructions

You must consider the following factors in determining the amount of training effort required in order to attain tangible physical and health benefits:

1. Intensity:
   The level of physical exertion in training must exceed the level of normal exertion without reaching the point of breathlessness and / or exhaustion. A suitable guideline for effective training can be taken from the pulse rate. During training this should rise to the region of between 70% to 85% of the maximum pulse rate (see the table and formular for determination and calculation of this). During the first weeks, the pulse rate should remain at the lower end of this region, at around 70% of the maximum pulse rate. In the
   course of the following weeks and months, the pulse rate should be slowly raised to the upper limit of 85% of the maximum pulse rate. The better the physical condition of the person doing the exercise, the more the level of training should be encreased to remain in the region of between 70% to 85% of the maximum pulse rate. This should be done by lengthening the time for the training and / or encreasing the level of difficulty. If the pulse rate is not shown on the computer display or if for safety reasons you wish to check your pulse rate, which could have been displayed wrongly due to error in use, etc., you can do the following:
   a. Pulse rate measurement in the conventional way (feeling the pulse at the wrist, for example, and counting the number of beats in one minute).
   b. Pulse rate measurement with a suitable specialised device (available from dealers specialising in health-related equipment).

2. Frequency
   Most experts recommend a combination of health-conscious nutrition, which must be determined on the basis of your training goal, and physical training three times a week. A normal adult must train twice a week to maintain his current level of condition. At least three training sessions a week are required to improve one’s condition and reduce one’s weight. Of course the ideal frequency of training is five sessions a week.

3. Planning the training
   Each training session should consist of three phases: the warm-up phase, the training phase, and the cool-down phase. The body temperature and oxygen intake should be raised slowly in the warm-up phase. This can be done with gymnastic exercises lasting five to ten minutes.
   Then the actual training (training phase) should begin. The training exertion should be relatively low for the first few minutes and then raised over a period of 15 to 30 minutes such that the pulse rate reaches the region of between 70% to 85% of  the maximum pulse rate.
   In order to support the circulation after the training phase and to prevent aching or strained muscles later, it is necessary to follow the training phase with a cooldown phase. This should be consist of stretching exercises and / or light gymnastic exercises for a period of five to ten minutes.

4. Motivation
   The key to a successful program is regular training. You should set a fixed time and place for each day of training and prepare yourself mentally for the training. Only train when you are in the mood for it and always have your goal in view. With continuous training you will be able to see how you are progressing day by day and are approaching your personal training goal bit by bit.

Calculation formula:| Maximum pulse rate
90% of the maximum pulse rate
85% of the maximum pulse rate
70% of the maximum pulse rate| = 220 – age (220 minus your age)
= (220 – age) x 0.9
= (220 – age) x 0.85
= (220 – age) x 0.7
---|---|---

Warm up exercises (Warm Up)

Start your warm up by walking on the spot for at least 3 minutes and then perform the following gymnastic exercises to the body for the training phase to prepare accor- dingly. The exercises do not overdo it and only as far run until a slight drag felt. This position will hold a while.

Reach with your left hand behind your head to the right shoulder and pull with the right hand slightly to the left elbow. After 20sec. switch arm.| Bend forward as far forward as possible and let your legs almost stretched. Show it with your fingers in the direction of toe. 2 x 20sec.| Sit down with one leg stretched out on the floor and bend forward and try to reach the foot with your hands. 2 x 20sec.| Kneel in a wide lunge forward and support yourself with your hands on the floor. Press the
pelvis down. Change after 20 sec leg.
---|---|---|---

After the warm-up exercises by some arms and legs shake loose. We recommend the warm-up exercises at the end of the training be conducted and to end your workout with shaking of the extremities. (Cool down)
Part-List + Spare-Part List
TM 650S Order No. 2035
Technical data: Issue: 22.02.2022
Treadmill without assembly directly ready for use

• 90% pre-assembled
• Motor continuous power 1 PS (0,74 kW), maximum motor power 2 PS (1,5 kW)
• Speed: 1 km/h to 16 km/h (in 0,1 km/h steps adjustable)
• Vibration absorbing running surface (Cushion System)
• 3 adjustable manual incline
• 1 manual program with possibility to enter personal limits such as time, distance and approx. calorie consumption.
• 15 predetermined training programs with programmed speed control
• Hand pulse measurement, speed and start/stop adjustment at handrail
• Safety belt stop
• Foldable for save space
• Fold-out Soft-Drop-System for a safety let down of the treadmill
• LED display with backlight touch buttons
• Direct selection keys for 4 km/h and 8 km/h
• Display show: time, distance, speed, approx.. calorie consumption, pulse r and body fat
• In the manual program it is
• Bluetooth-Verbindung für Kinomap – APP (für iOS und Android)
• Holder for tablet + smartphone
• Suitable for maximum body weight of.120 kg
• Measurement of run area (LxW). :120 x 40 cm
• Electrical data: 220-240V/50-60Hz /740 Watt

Product weight approx. 41 kg
Dimension approx. (LxWxH): L148 x W 65 x H 117 cm
Dimension folded (LxWxH): ca. L 76 x W 65 x H 130 cm
Please check after opening the packing that all the parts shown in the following assembly steps are there. Once you are sure that this is the case, you can start assembly. Please contact us if any components are defective or missing, or if you need any spare parts or replacements in future:

Adresse:| Top-Sports Gilles GmbH
Friedrichstraße 55
42551 Velbert
Telefon: +49 (0) 20 51 / 60 67-0
Telefax: +49 (0) 20 51 / 60 67-44
e-mail: info@christopeit-sport.com
www.christopeit-sport.com
---|---

This treadmill is created only for private Home sports activity and not allowed to us in a commercial or professional area. Home Sport use class H/C

Illustr. No.| Designation| Dimension   mm| Quantity| Attached to Illustr. No.| ET-Number
---|---|---|---|---|---
1| Main frame| | 1| 2| 33-2035-01-SW
2| Base frame| | 1| 1| 33-2035-02-SW
3| Left upright tube| | 1| 2| 33-1935-03-SW
4| Right upright tube| | 1| 2| 33-2035-04-SW
5| Computer bracket| | 1| 3+4| 33-2035-05-SW
6| Screw| 4×25| 4| 2+27| 39-9909-SW
7| Cushion| | 4| 1| 36-2035-10-BT
8| Washer| 10//20| 2| 54| 39-9989
9| Front roller| | 1| 1| 33-2035-06-SI
10| Rear roller| | 1| 1| 33-2035-07-SI
11| Cylinder| | 1| 1+2| 36-2035
12| Allen wrench| 5mm| 1| | 36-9119-34-BT
13| DC motor| | 1| 1| 33-2035-08-SI
14| Running board| | 1| 1| 36-2035-04-BT
15| Bolt| M6x35| 4| 14| 39-10435-CR
16| Incline foot| | 2| 1| 36-2035-05-BT
17| Handrail plug| | 2| 5| 36-2035-16-BT
18| Motor cover| | 1| 1| 36-2035-01-BT
19| Bolt| 4×20| 2| 59-60| 39-10519
20| Side rail| | 2| 1| 36-2035-07-BT
21| Right back end cap| | 1| 1| 36-2035-08-BT
22| Left back end cap| | 1| 1| 36-2035-09-BT
23| Locking pin| | 2| 16| 36-2035-17-BT
24| Motor belt| | 1| 9+13| 36-2035-18-BT
25| Power wire buckle| | 1| 1+31| 36-2035-19-BT
26| Running belt| | 1| 9+10| 36-2035-02-BT
27| Foot pad| | 4| 2| 36-2035-20-BT
28| Cable save| | 2| 41| 36-2035-21-BT
29| Transportation wheel| | 2| 2| 36-2035-22-BT
30| Bolt| M6x35| 2| 3,4+5| 39-10435-CR
31| AC power cable| | 1| 40| 36-1241-18-BT
32| Switch| | 1| 1| 36-1241-17-BT
33| Foam| | 2| 5| 36-2035-23-BT
34| Screw| 4×13| 13| 35,36+81| 39-10187
35| Computer top cover| | 1| 5+36| 36-2035-03-BT
36| Computer bottom cover| | 1| 35| 36-2035-12-BT
37| Smartphone or tablet holder| | 1| 35| 36-2035-13-BT
38| Speed +/- remote keys| | 1| 5| 36-2035-14-BT
39| Start/stop remote keys| | 1| 5| 36-2035-15-BT
40| Control board| | 1| 1| 36-2035-06-BT
41| Computer bottom wire| | 1| 35+40| 36-2035-24-BT
42| Bolt| M6x65| 2| 10| 39-10066-SW
43| Barb cushion 1| | 2| 1| 36-2035-25-BT
44| Ferrite ring| | 1| 40| 36-1241-19-BT
45| Connection cable| | 1| 35+41| 36-1241-20-BT
46| Hex screw| M8x25| 3| 11| 39-10455
47| Nylon nut| M6| 10| 15,30+69| 39-9861-SW
48| Screw| 4×30| 4| 21+22| 39-9909
49| Motor bottom cover| | 1| 1| 36-2035-11-BT
50| Barb cushion 2| | 2| 1| 36-2035-26-BT
51| Bolt| M8x15| 4| 5-Feb| 39-9823
52| Hex screw| M8x40| 2| 2+29| 39-9817
53| Bolt| M8x45| 3| 11| 39-10124-VC
54| Hex screw| M10x55| 2| 1+2| 39-9976-SW
55| Washer| 8//16| 2| 80| 33-9962-CR
56| Inner – hex screw| M6x55| 1| 9| 39-9979
57| Cross – head screw| M5x8| 5| 1+18| 36-9990
58| Nylon nut| M8| 6| 46,52,53+70| 39-9918-CR
59| Left support cover| | 1| 2| 36-2035-27-BT
60| Right support cover| | 1| 2| 36-2035-28-BT
61| Running board support tube| | 2| 1| 33-2035-09-SW
62| Support tube cushion| | 4| 61| 36-2035-29-BT
63| Washer| 5//10| 2| 57| 39-10111-SW
64| Washer| 8//16| 12| 46,51-53+70| 33-9962-CR
65| Washer| 6//12| 3| 42+56| 39-10439
66| Isolation nylon pad| | 4| 61| 36-2035-30-BT
67| Spring washer| for M8| 2| 80| 39-9864-VC
68| Overload protector| | 1| 1+40| 36-2035-31-BT
69| Bolt| M6x30| 4| 1+14| 39-10435-CR
70| Inner – hex screw| M8x45| 4| 3,4+16| 39-10124-VC
71| Safety key| | 1| 81| 36-2035-32-BT
72| Silicone oil| | 1| | 36-1935-40-BT
73| Spring washer| for M5| 2| 57| 39-9870
74| Inductor| | 1| 1+40| 36-1940-58-BT
75| Screw| 4×15| 4| 5+35| 39-10515
76| Bolt| 4×45| 4| 5,38+39| 39-10521
77| Bolt| 4×10| 8| 21,22,40+83| 39-10518
78| Multi tool| | 1| | 36-9107-27-BT
79| Screw| 4×12| 8| 49| 39-10518
80| Inner – hex screw| M8x12| 2| 1+13| 39-9922
81| Safety key socket| | 1| 35| 36-2035-33-BT
82| Filter| | 1| 1+40| 36-1940-59-BT
83| Assembly and exercise instructions| f| 1| | 36-2035-34-BT

Service / Hersteller
Bei Reklamationen, notwendigen Ersatzteilbestellungen oder Reparaturen wenden Sie sich bitte an unsere Service Abteilung.

© by Top-Sports Gilles GmbH
D-42551 Velbert (Germany)
Service:
Tel.: +49 (0)2051/6067-0
Fax: +49 (0)2051/6067-44
Top-Sports Gilles GmbH
Friedrichstrasse 55
D – 42551 Velbert
info@christopeit-sport.com
http://www.christopeit-sport.com
02.2022- Druckfehler vorbehalten

References

• Christopeit Sport - Fitnessgeräte in Top-Markenqualität
• Kinomap
• Kinomap
• Kinomap

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>