BAFANG DP C07.CAN LCD Display CAN User Manual
- June 12, 2024
- BAFANG
Table of Contents
- BAFANG DP C07.CAN LCD Display CAN
- Product Information
- Specifications
- Key Definitions
- Product Usage Instructions
- Walk Assistance
- IMPORTANT NOTICE
- INTRODUCTION OF DISPLAY
- PRODUCT DESCRIPTION
- Functional Overview
- DISPLAY
- KEY DEFINITION
- NORMAL OPERATION
- SETTINGS
- ERROR CODE DEFINITION
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BAFANG DP C07.CAN LCD Display CAN
Product Information
The DP C07.CAN is a display unit designed for use with a pedelec. It provides important information and control options for the pedelec system. The display features a clear and easy-to-read screen, with various functions and settings available.
Specifications
- Display of battery capacity in real-time
- Kilometer stand, daily kilometers (TRIP), total kilometers (TOTAL)
- Indication of headlights/backlighting status
- Walking assistance feature
- Speed unit and digital speed display
- Speed mode options: top speed (MAXS) and average speed (AVG)
- An error indicator for troubleshooting
- Data display corresponding to the current mode
- Support level selection
Key Definitions
- Up: Increase value or navigate up
- Down: Decrease value or navigate down
- Light On/Off: Toggle headlights or backlighting
- System On/Off: Turn the system on or off
- OK/Enter: Confirm selection or enter the menu
Product Usage Instructions
Switching the System ON/OFF
To turn on the system, press and hold the System On/Off button on the display for more than 2 seconds. To turn off the system, press and hold the System On/Off button again for more than 2 seconds. If the automatic shutdown time is set to 5 minutes, the display will automatically turn off within that time when not in use.
Selection of Support Levels
When the display is turned on, press and hold the button for 2 seconds to turn off the headlight and the display backlight. The brightness of the backlight can be adjusted in the display settings. If the display is turned on in a dark environment, the display backlight and headlight will automatically be switched on. If manually switched off, the automatic sensor function is deactivated.
Battery Capacity Indication
The battery capacity is shown on the display with ten bars. Each full bar represents the remaining capacity of the battery in percentage. If the frame of the indicator blinks, it means the battery needs to be charged.
Walk Assistance
The walk assistance feature can only be activated when the pedelec is in a stationary position. To activate it, briefly press the designated button.
IMPORTANT NOTICE
- If the error information from the display cannot be corrected according to the instructions, please contact your retailer.
- The product is designed to be waterproof. It is highly recommended to avoid submerging the display underwater.
- Do not clean the display with a steam jet, high-pressure cleaner or water hose.
- Please use this product with care.
- Do not use thinners or other solvents to clean the display. Such substances can damage surfaces.
- Warranty is not included due to wear and normal use and aging.
INTRODUCTION OF DISPLAY
- Model: DP C07.CAN BUS
- The housing material is PC and Acrylic, and the button material is made of silicone.
- The label marking is as follows:
Note: Please keep the QR code label attached to the display cable. The information from the Label is used for a later possible software update.
PRODUCT DESCRIPTION
Specifications
- Operating temperature: -20℃~45℃
- Storage temperature : -20℃~50℃
- Waterproof: IP65
- Bearing humidity: 30%-70% RH
Functional Overview
- Speed display (including speed in real time (SPEED), top speed (MAXS) and average speed (AVG), switching between km and miles)
- Battery capacity indicator
- Automatic sensors explanation of the lighting system
- Brightness setting for backlight
- Indication of performance support
- Walk assistance
- Kilometer stand (including single-trip distance, total distance)
- Display for the remaining distance.(Depends on your riding style)
- Motor output power indicator
- Energy consumption indicator CALORIES
- (Note: If the display has this function)
- Error messages view
- Service
DISPLAY
- Display of battery capacity in real time.
- Kilometer stand, Daily kilometers (TRIP) – Total kilometers (TOTAL).
- The display shows this symbol if the light is on.
- Walking assistance .
- Service: please see the service section.
- Menu.
- Speed unit.
- Digital speed display.
- Speed mode , top speed (MAXS) – Average speed (AVG).
- Error indicator .
- Data: Display data, which corresponds to the current mode.
- Support level
KEY DEFINITION
NORMAL OPERATION
Switching the System ON/OFF
Press and hold on the display to turn on the system. Press and hold again to
turn off the system. If the “automatic shutdown time” is set to 5 minutes (it
can be set with the “Auto Off” function, See “Auto Off”), the display will
automatically be turned off within the desired time when it is not in
operation.
Selection of Support Levels
When the display is turned on, press the or button to switch to the support
level, the lowest level is 1, and the highest level is 5. When the system is
switched on, the support level starts in level 1. There is no support at level
null.
Selection mode
Briefly press the button to see the different trip modes. Trip: daily
kilometers (TRIP) – total kilometers (TOTAL) – Maximum speed (MAXS) – Average
speed (AVG) – Remaining distance (RANGE) – Output power (W) – Energy
consumption (C (only with torque sensor fitted)).
Headlights/backlighting
Hold the button to activate the headlight and the display backlight.
Hold the button again to turn off the headlight and the display backlight. The
brightness of the backlight can be set in the display settings “Brightness”.
(If the display /Pedelec is switched on in a dark environment, the display
backlight/headlight will automatically be switched on. If the display
backlight/headlight has been manually switched off, the automatic sensor
function is deactivated. You can only turn on the light manually after
switching on the system again.)
Walk Assistance
The Walk assistance can only be activated with a standing pedelec.
Activation: Briefly press (<0.5S) the button until to level null, and
then press (<0.5s) the button, and the symbol is displayed. Now hold down the
button and the Walk assistance will activate. The symbol will flashes and the
pedelec moves approx. 4.5 km/h. After releasing the button, the motor stops
automatically and switches back to level null (if no any option be activated
in 5 seconds). If no speed signal is detected, it shows 2.5km/h.
Battery capacity indication
The battery capacity is showed in ten bars. Each full bar represents a
remaining capacity of the battery in a percentage, if the frame of indicator
blinks that means to charge. (as shown in the figure below):
| Bars | Charge in Percentage |
|---|---|
| 10 | ≥90% |
| 9 | 80%≤C<90% |
| 8 | 70%≤C<80% |
| 7 | 60%≤C<70% |
| 6 | 50%≤C<60% |
| 5 | 40%≤C<50% |
| 4 | 30%≤C<40% |
| 3 | 20%≤C<30% |
| 2 | 10%≤C<20% |
| 1 | 5%≤C<10% |
| Blinking | C≤5% |
SETTINGS
After the display is turned on, quickly press the button twice to access the
“MENU” interface. pressing the button, you can select and reset the options.
Then press the button twice to confirm your selected option and return to the
main screen. If no button is pressed within 10 seconds in the “MENU”
interface, the display will automatically return to the main screen and no
data will be saved.
Reset mileage
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface and “tC” appears on the display (as shown below). Now using
the button, choose between “y”(YES) or “n”(NO). If choose “y”, the Daily
kilometers (TRIP), Maximum speed (MAX) and Average speed (AVG) will be reset.
Once you have chosen your desired selection, press (<0.3S) the button twice to
save and return to the main screen, or you can press (<0.3S) the button once
to save and enter the next item “Selection of unit in km/Miles”.
NOTE: If the daily kilometers accumulate 99999km, the daily kilometers will be reset automatically
Selection of unit in km/Miles
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “S7” appears on
the display (as shown below). Now using the button, choose between “km/h” or
“mile/h”. Once you have chosen your desired selection, press (<0.3S) the
button twice to save and return to the main screen, or you can press (<0.3S)
the button once to save and enter the next item “Set light sensitivity
”.
Set light sensitivity
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “bL0” appears on
the display (as shown below). And then press to increase or to reduce (light
sensitivity for 0-5). Chose 0 means turn off the light sensitivity. Once you
have chosen your desired selection, press (<0.3S) the button twice to save and
return to the main screen, or you can press (<0.3S) the button once to save
and enter next item “Set display brightness”.
Set display brightness
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “bL1” appears on
the display (as shown below). And then press to increase or to reduce
(brightness for 1-5). Once you have chosen your desired selection, press
(<0.3S) the button twice to save and return to the main screen, or you can
press (<0.3S) the button once to save and enter next item “Set Auto Off”.
Set Auto Off
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “OFF” appears on
the display (as shown below). And then press to increase or to reduce
(brightness for 1-9minute). Once you have chosen your desired selection, press
(<0.3S) the button twice to save and return to the main screen, or you can
press (<0.3S) the button once to save and enter next item “Service Tip”.
Service Tip
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “nnA” appears on the
display (as shown below). And then press to choose between0 Choose 0 means
turn off the notification. Once you have chosen your desired selection, press
(<0.3S) the button twice to save and return to the main screen.
NOTE: If the “Service” function switch on, every 5000 km (the mileage of more than 5000 km) the indicator “” is displayed every time at switch on.
View Information
All data in this item cannot be changed, only to be viewed.
Wheel Size
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “LUd” appears on
the display (as shown below). Once you have viewed your desired information,
press (<0.3S) the button twice to return to the main screen, or you can press
(<0.3S) the button once to enter next item “Speed Limit”.
Speed Limit
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “SPL” appears on the
display (as shown below). Once you have viewed your desired information, press
(<0.3S) the button twice to return to the main screen, or you can press
(<0.3S) the button once to enter next item “Controller hardware info”.
Controller hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “CHc (Controller
Hardware check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to return to the main
screen, or you can press (<0.3S) the button once to enter next item
“Controller software info”.
Controller software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “CSc (Controller
Software check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return
to the main screen, or you can press (<0.3S) the button once to enter next
item “Display hardware info”.
Display hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “dHc (Display
Hardware check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return to
the main screen, or you can press (<0.3S) the button once to enter next item
“Display software info”.
Display software info
When the system is on, quickly press(<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “dSc (Display
Software check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return to
the main screen, or you can press (<0.3S) the button once to enter next item
“BMS hardware info”.
BMS hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “bHc (BMS
Hardware check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return to
the main screen, or you can press (<0.3S) the button once to enter the next
item “BMS software info”.
BMS software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “dSc (Display
Software check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return to
the main screen, or you can press (<0.3S) the button once to enter next item
“Sensor hardware info”.
Sensor hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “SHc (Sensor
Hardware check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return to
the main screen, or you can press (<0.3S) the button once to enter next item
“Sensor software info”.
NOTE: This information is not displayed, if there are no torque sensor in the drive system.
Sensor software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “SSc (Sensor
Software check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return to
the main screen, or you can press (<0.3S) the button once to enter the next
item “Battery info”.
NOTE: This information is not displayed, if there are no torque sensor in the drive system.
Battery Information
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “b01” appears on the
display (as shown below). You can briefly press (0.3s) to view all information
of the battery. Once you have viewed your desired information, press (<0.3S)
the button twice to save and return to the main screen, or you can press
(<0.3S) the button once to enter next item “Message of Error Code”. 
NOTE: If no data is detected, “–” is displayed.
The message of Error Code
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, and repetitively press the button until the “E00” appears on
the display (as shown below). You can briefly press (0.3s) to view last ten
Error Code “EO0” to “EO9”. Error code “00” means that there is no error. Once
you have viewed your desired information, press (<0.3S) the button twice to
save and return to the main screen.
ERROR CODE DEFINITION
The display can show the errors of a pedelec. If an error is detected, the
wrench icon appears on the display and one of the following error codes will
be displayed.
Note: Please read the description of the error code carefully. If you see
the error code, restart the system first. If the problem is not resolved,
please contact your dealer.
| Error | Declaration | Troubleshooting |
|---|
04
|
The throttle has fault.
| 1. Check the connector of throttle whether they are correctly connected.
2. Disconnect the throttle, If the problem still occurs, please contact your retailer.
(only with this function)
05
|
The throttle is not back in its correct position.
| Check the throttle can adjust back into its correct position, if the situation does not improve, please change to a new throttle.(only with this function)
07
|
Overvoltage protection
| 1. Remove the battery.
2. Re-Insert the battery.
3. If the problem persists, please contact your retailer.
08
| Error with the hall sensor signal inside the motor|
Please contact your retailer.
09| Error with the Engine phase’s| Please contact your retailer.
10
|
The temperature inside the engine has reached its maximum protection value
| 1. Turn off the system and allow the Pedelec to cool down.
2. If the problem persists, please contact your retailer.
11
| The temperature sensor inside the motor has an error|
Please contact your retailer.
12
| Error with the current sensor in the controller|
Please contact your retailer.
13
| Error with the temperature sensor inside of the battery|
Please contact your retailer.
| Error | Declaration | Troubleshooting |
|---|
14
|
The protection temperature inside the controller has reached its maxi- mum protection value
| 1. Turn off the system and let the pedelec cool down.
2. If the problem persists, please contact your retailer.
15
| Error with the temperature sensor inside the controller|
Please contact your retailer.
21
|
Speed sensor Error
| 1. Restart the system
2. Check that the magnet attached to the spoke is aligned with the speed sensor and that the distance is between 10 mm and 20 mm.
3. Check that the speed sensor connector is connected correctly.
4. If the error persists, please contact your retailer.
25
|
Torque signal Error
| 1. Check that all connections are connected correctly.
2. If the error persists, please contact your retailer.
26
|
Speed signal of the torque sensor has an error
| 1. Check the connector from the speed sensor to make sure it is connected correctly.
2. Check the speed sensor for signs of damage.
3. If the problem persists, please contact your retailer.
27| Overcurrent from controller| Please contact your retailer.
30
|
Communication problem
| 1. Check all connections are correctly con- nected.
2. If the error persists, please contact your retailer.
33
|
Brake signal has an error (If brake sensors are fitted)
| 1. Check all connectors.
2. If the error continues to occur, please con- tact your retailer.
| Error | Declaration | Troubleshooting |
|---|---|---|
| 35 | Detection circuit for 15V has an error | Please contact your retailer. |
36
| Detection circuit on the keypad has an error|
Please contact your retailer.
37| WDT circuit is faulty| Please contact your retailer.
41
| The total voltage from the battery is too high|
Please contact your retailer.
42
| The total voltage from the battery is too low|
Please contact your retailer.
43
| The total power from the battery cells is too high|
Please contact your retailer.
44| The voltage of the single cell is too high| Please contact your retailer.
45
| The temperature from the battery is too high|
Please contact your retailer.
46
| The temperature of the battery is too low|
Please contact your retailer.
47| The SOC of the battery is too high| Please contact your retailer.
48| The SOC of the battery is too low| Please contact your retailer.
61
|
Switching detection defect
| Please contact your retailer. (only with this function)
62
|
The electronic derailleur cannot release.
| Please contact your retailer. (only with this function)
71
|
The electronic lock is jammed
| Please contact your retailer. (only with this function)
81
|
The Bluetooth module has an error
| Please contact your retailer. (only with this function)
BF-UM-C-DP C07-EN November 2019