TSI 7590 OmniTrak Smart Station Instruction Manual

Smart Station
Model 7590
Instruction Manual

Operation Instructions

1. Power On: On the right side of the Smart Station, hold circle power button down for 3 seconds.
2. Power Off: On the right side of the Smart Station, hold circle power button down for 2 seconds. Two options then pop-up on the screen to either Power Off or Restart.
3. Charging: Plug USB-C cable into bottom of device and then into power source
4. Connecting to a Module: Power on module by holding down the circle on the left for 1 second. A blue LED light will start to blink indicating Bluetooth® is on.
   – The module will appear in the list on the Smart Station. If not, hit Refresh.
   – Press desired module on screen to connect to Smart Station. A green check mark indicates a successful connection.
   – Press Done

Now you’re ready to take measurements.
The Omni Trak™ Smart Station can be used in conjunction with any Omni Trak™ Module to provide immediate feedback as to the conditions in the immediate area. Take measurements, create reports, and analyze data provided to help improve conditions. This instrument is a handheld device, not to be worn on the body, or near an individual’s head.
Dispose of battery in accordance with local rules and regulations.

Specifications

AC and DC Power Requirements

Environmental/Installation Requirements

Compliance

FCC ID: 2A22JOTSTATION
IC ID: 28101-OTSTATION

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Per FCC 15.21 Changes or modifications not expressly approved by TSI will void the product warranty and may void the user’s authority to operate the equipment.
This device contains license-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s license- exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

To satisfy RF exposure requirements, this device and its antenna may be operated near a persons body and the extremities, but must be operated with a separation distance of at least 20 cm from all person’s head.
LASER WARNING

• Omni Trak™ Modules are Class 1 laser-based instruments.
• During normal operation, you will not be exposed to laser radiation.
• DO NOT open the Omni Trak™ Module when it is powered ON.
• You will not be exposed to the laser radiation when the Omni Trak™ Module is disassembled.
• The PM sensor has a laser inside it. DO NOT open the PM sensor inside Omni Trak Module when the Omni Trak Module is powered.

WARNING

• DO NOT attempt to replace the battery in this instrument.
• DO NOT abuse the battery in any way as the battery may rupture or catch fire.
• DO NOT use a substitute or non-rechargeable battery in this instrument.
• DO NOT short-circuit, incinerate, dismantle or mutilate Lithium ion batteries
• DO NOT expose to water or heat.
• DO NOT use any battery which shows signs of damage, such as bulging, swelling, a swollen plastic wrap, liquid in the plastic wrap, etc.

Specifications are subject to change without notice.
Wi-Fi is a registered trademark of Wi-Fi Alliance®.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
TSI, and the TSI logo are registered trademarks of TSI Incorporated in the United States and may be protected under other country’s trademark registrations.

Knowledge Beyond Measure
TSI Incorporated – Visit our website www.tsi.com for more information.
USA Tel: +1 800 874 2811
UK Tel: +44 149 4 459200
Germany Tel: +49 241 523030
P/N 5003016 Rev B
©2023 TSI Incorporated
Printed in U.S.A.
4420176118

References

• Home | TSI

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>