XGIMI MoGo 2 Pro Portable Projector User Guide
- June 12, 2024
- XGIMI
Table of Contents
XGIMI MoGo 2 Pro Portable Projector User Guide
Overview
Front view
A: ToF Autofocus
B: Lens
C: Auto Keystone Correction
Note: To prevent auto keystone correction failure, avoid blocking the sensor.
Rear view
Note:
- The Type-C port only supports power supply.
- Using a non-XGIMI standard adapter may have a certain impact on the brightness and volume. For the best experience, it is recommended to use the XGIMI standard adapter.
Remote control
A: Power
B: Focus
C: Google Assistant
D: Navigation
E: Return
F: Settings/Menu
G: Home
H: Volume
Please read the Product Instructions carefully before using the product.
Thank you for buying and using the products of XGIMI Technology Co., Ltd.
(hereinafter referred to as “XGIMI Technology” or “XGIMI”). You should read
the Product Instructions carefully before using this product for both your
safety and interests. XGIMI Technology will assume no responsibility for any
personal injury, damage to property or other loss caused because due to
failure to operate this product according to the Product Instructions or
precautions.
About the Product Instructions (hereinafter referred to as “the
Instructions”)
Copyright of the Instructions belongs to XGIMI Technology;
Trademarks and names mentioned in the Instructions belong to their respective
right owners; In the case of inconformity between the content of the
Instructions and the actual product, the actual product shall prevail.
Google, Android TV, and Chromecast built-in are trademarks of Google LLC.
Google Assistant is not available in certain languages and countries.
HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Dolby, Dolby Audio, and double-D symbol are trademarks of Dolby Laboratories.
Disposal instructions for used products:
The product is designed and manufactured with high quality materials and
components that are recyclable.
This symbol on the product indicates that it is protected under the Directive
2012/19/EU.
Getting Started
Power on / off
Connect the device to a power source and press” ” to turn on the device.
When the device is on, press” ” to turn the device off.
Remote control pairing
Place the remote control within 10cm of the device, press” “and ”
“simultaneously, an indicator light will begin flashing as the remote control
enters pairing mode. Release the buons as soon as flashing begins, and the
connection is successful when a “Ding” is heard. If pairing fails, repeat the
above steps after 30s.
Remote control functions
Focus adjustment function
Short press the” ” to trigger autofocus. Long press the” ” to trigger manual
focus.
Shortcut buon
To access the shortcut buon function, briefly press the” ” .
Intelligent Screen Adaption technology
When the automatic keystone function is enabled, the frame will be adjusted
automatically if you move the device to another location.
When the automatic obstacle avoidance function is enabled, the frame will
automatically avoid any obstacles that block projection area. When the
automatic screen alignment function is enabled, the frame will automatically
adjust to an aspect ratio of 16:9 or 16:10.
Press the ” “on the remote control to enter the “Keystone Correction” page.
Select “Auto Keystone Correction” to enable the automatic keystone correction
function. Select “Manual Keystone Correction” to manually adjust the four
points and size of the projection area.
Google Assistant
Google Assistant can be activated by pressing the” “buon on the remote
control. Using your voice, you can quickly access entertainment, control smart
devices, and get answers on screen.
Setting
Adjust device and image seings at any interface by pressing ” ” on the remote
control. Specific functions for various seings are as follows:
Clear Apps | Remove apps from the device |
---|---|
Keystone Correction | Adjust the keystone for the projected image |
Image mode | Adjust image parameters under the video or signal source |
Sound Settings | Adjust the device’s voice output channel |
3D Video Setup | 3D seings for video and signal sources |
Sleep Timer | Automatically shut down the device after a pre-set time |
All settings | Seings for other related functions |
- 3D mode and Image mode settings can only be adjusted via the video play or signal source channel.
- Frame ratio and HDMI version settings can only be adjusted via the HDMI channel.
Chromecast built-inTM
- Cast your favorite entertainment apps—movies & TV shows, music, games, sports and more—from your Android, iOS device, Mac, Windows computer, or Chromebook to the device. Find Chromecast-enabled apps at g.co/castapps.
- Quickly cast video and audio contents to the TV through ” “of mobile application supported.
- Screencasting will not be interrupted due to calling or message sending, and the mobile phone baery consumption is minimal.
- The whole frame of Android phones or Chrome browser on PC can be cast to the TV.
Note:
Screencasting is optimized for selected services only. Streaming quality for
other content might vary. Supported operating systems and devices:
AndroidTM2.3 Gingerbread and higher, i0S® 7 and higher, Windows® 7 and higher,
Mac OS.10.7 and higher and Chrome OS (version 38 or higher).
System upgrade
Online upgrade
The online upgrade can be made through system seing
WARNING:
Please refer to the information on the exterior boom of the enclosure for
electrical and safety information before installing or operating the
apparatus.
Warning for remote controller and portal device
- There is a risk of explosion if the baery is replaced with the wrong type of baery;
- Disposal of a baery into fire, mechanically crushing or cuing the baery, may result in an explosion;
- Do not leave baery in an environment with extremely high temperature that may result in an explosion or the leakage of flammable liquid or gas;
- Do not put baery in an environment with extremely low pressure that may result in an explosion or the leakage of flammable liquid or gas.
Correct use of the device:
- Do not face lens into eyes as injury to the eyes can be caused by the strong projector light.
- Do not block the air inlet/outlet of the device in order to avoid damage to internal electronic devices arising from normal heat dissipation failure of the device.
- Do not wipe the lens directly with cleaning tools including paper and cloth etc. in order to avoid damage to lens; please clean up the dust on the lens surface through clean air blowing.
- Do not wash the device with chemicals, detergents or any liquid in order to avoid corrosion of circuit board by rainwater, moisture and mineral-containing liquids.
- Keep the device and its components and accessories out of reach of children.
- Ensure that the device is used in a dry and ventilated environment.
- Do not store the device in overheated or overcooled places, because extreme temperatures will shorten the life of electronic devices. Permissible environ ment for storage and use of the device in an environment of 0°C-40°C.
- Do not put the device into any heating equipment (such as dryer and microwave oven etc.) for drying.
- Do not extrude the device firmly or place barriers on it or its back to avoid damage to the device.
- Do not throw, strike or sharply vibrate the device to avoid damage to the internal circuit board.
- Do not try to disassemble and assemble the device yourself. Please contact after-sales service of XGIMI for any problem.
- Do not repair any product on your own. In the case of normal operation failure of the device or any component, you shall consult after-sales service of XGIMI promptly or return it to the factory for repair.
- Operations in the 5.15-5.35 GHz band are restricted to indoor usage only.
- In the installation and operation of the device, the for distance between radiator and body should be at least 20cm.
- As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015
- Use careful with the earphone maybe excessive sound pressure from earphones and headphones can cause hearing loss.
- Adapter plug is used as the disconnect device, so the disconnect device shall remain readily operable.
FCC warning
The device meets provisions of part 15 of FCC rule. Operation meets the
following 2 conditions:
(1) the device will not cause harmful interference, and (2) the device must
accept any interference received, including interference that may result in
accidental operations. Users that intentional or unintentional modification
and replacement of radiators without explicit approval from the responsible
compliance party may prevent the user from operating the device. If the manual
is provided in a form other than paper, such as, provided in computer disk
through the Internet, then the information required in the section can be
included in the manual in the alternative form under the premise that users
can have access to the form information.
For B-class digital or peripheral device, instructions provided by users shall include the following or similar statements and put them in a prominent place of manual text:
- Reposition direction of receiving antenna.
- Increase the distance between the device and the receiver.
- Connect the device to a circuit socket different from the circuit connected to the receiver.
- Consult distributors or experienced radio/television technicians to seek help
Declaration of Conformity
XGIMI Technology Co., Ltd hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU ,Radio Equipment Regulations 2017,Directive 2011/65/EU and UK. The Restriction of the Use of Certain Hazardous Substances in Electrical , Electronic Equipment Regulations 2012, and compliance with REACH Directive (Regulation No 1907/2006). This product is allowed to be used in some of EU member states as illustrated in the right chart. This Frequency applies to the following Member States or the geographical area within a Member State where restrictions on puing into service or requirements for authorisation of use exist.
You can find the Declaration of Conformity on
https://global.xgimi.com/pages/product-support
ISED Warning
This device complies with Innovation, Science and Economic Evelopment Licence- exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
The device is compiled by using FCC and ISED Innovation, Science and Economic
Evelopment radiation exposure limits specified for uncontrolled environments.
The transmier shall not be placed or operated in conjunction with any other
antenna or transmier.
For the LED projector, the device meets FCC and ISED Innovation, Science and
Economic Evelopment radiation exposure limits specified uncontrolled
environments.
- Only use aachments/accessories specified or providedby the manufacturer (such as the exclusive supply adapter etc).
- Beware that this product may emit harmful light radiation.
Wireless Specification
- Bluetooth version: 5.2
- Bluetooth transmier frequency range: 2400 MHz – 2483.5 MHz
- Bluetooth transmier power: ≤17 dBm (EIRP)
- Wi-Fi network: IEEE 802.11 a/b/g/n/ac (2.4GHz/5GHz)
- 2.4G Wi-Fi transmier frequency range: 2412 – 2472 MHz (2.4 GHz ISM Band, USA 11 Channels, Europe and others 13 Channels)
- 2.4G Wi-Fi transmier power: ≤17 dBm (EIRP)
- 5G Wi-Fi transmier frequency range: 5.15 – 5.35GHz, 5.470 – 5.725GHz, 5.725 – 5.850GHz
- 5G Wi-Fi transmier power: 5.15 – 5.25GHz < 22dBm (EIRP), 5.25 – 5.35GHz & 5.470 – 5.725GHz < 19dBm (EIRP), 5.725 – 5.825GHz < 13dBm (EIRP)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>