Carlson 0680 PW Mini Step Over Gate With Small Pet Door Installation Guide
- June 17, 2024
- Carlson
Table of Contents
Carlson 0680 PW Mini Step Over Gate With Small Pet Door
Mini Step-Over Gate with Small Pet Door
- READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THE GATE. KEEP INSTRUCTIONS FOR FUTURE USE.
- www.carlsonpetproducts.com
- Carlson Pet Products, Inc.
- 3200 Corporate Center Drive, Suite 105 / Burnsville, MN 55306, USA/, E.U./, EE. UU. 952.435.1084.
Before Assembly
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS
- A Gate Frame
- B 0 4″ Extension
- C Wall Cups (4)
- D 1″ Wall Mount Screws
- E Threaded Spindle Rods
- F Foot Stands (2)
NOTE
- MODEL NO.
- 0680PW
- MAX SIZE
- 18↔31 in, 18 in tall
BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using it. The safety of your pet and/or child is your responsibility. Please keep these instructions for your reference.
IMPORTANT
- Never use more than two extensions per side of the gate.
- If hardware mounting to a surface other than drywall or wood, please consult with a professional about installation.
REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4)threaded spindle rods to depressurize the gate from its doorway or opening.
Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tigntened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under
reasonable and non-commercial use and conditions of maintenance, it fails
while owned by the original purchaser because of the quality of materials or
workmanship of finish and assembly, Carlson Pet Products, Inc. will replace or
repair it at Carlson’s option. PROOF OF PURCHASE REQUIRED.
Assembling and Installing Your Gate
STEP 1
Attach all the provided panels (B) together.
STEP 2
Locate the (4) threaded spindle rods (E) Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot.
NOTE: It may be necessary to hold the threaded spindle rods or rubber feet while rotating the adjustment wheels to ensure the entire unit does not rotate.
STEP 3
Attach the 2-foot stands (F) to the bottom of the gate.
STEP 4
Insert the (4) threaded spindle rods into the holes at each of the four corners of the gate.
NOTE: The ends of the gate frame are not threaded. The threaded spindle rods should slide into the end of the frame tubes without any resistance.
STEP 5
Position the gate so that it is level and centered within your doorway or opening. Rotate the adjustment wheels on the threaded spindle rods in the opposite direction as in Step 2, expanding the gap between the rubber foot and the adjustment wheel. Expand each of the (4) threaded spindle rods until they make contact with the doorway or opening. Do not fully tighten the threaded spindle rods yet.
NOTE: The gap between the gate and wall should not exceed more than 2.5 inches. Make the appropriate adjustment to ensure you have installed your gate safely.
STEP 6
To use the small pet door, pull back on the spring pin.
Positioning and Attaching Wall Cups
- After you have mounted your gate, and you are satisfied with its positioning, draw a circle on the surtace of your doorway or opening around the perimeter of the (4) rubber feet. Next, completely remove the gate from the opening by loosening each of the (4) threaded spindle rods to depressurize the gate.
- With the gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your (4) wall cups (C). Center each of the wall cups within the guide circles and use the provided self-tapping 25mm screws (DI to fasten them in place via the hole through the center of each wall cup.
- Reinstall your gate in the doorway or opening according to the instructions, using the newly installed wall cups as anchoring points for the (4) threaded spindle rods.
WARNING
- INSTALL ACCORDING TO MANUFACTURES INSTRUCTIONS.
- NOT RECOMMENDED FOR USE WITH CHILDREN.
- TO PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL THE GATE AND USE IT ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
- CHILDREN HAVE DIED OR BEEN SERIOUSLY INJURED WHEN GATES ARE NOT SECURELY INSTALLED. ALWAYS INSTALL AND USE THE GATE AS DIRECTED USING ALL REQUIRED PARTS.
- YOU MUST INSTALL WALL CUPS TO KEEP THE GATE IN PLACE. WITHOUT WALL CUPS, CHILD CAN PUSH OUT AND ESCAPE.
- NEVER STACK GATES ON TOP OF EACH OTHER TO FORM A TALLER BARRIER. THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
- INTENDED FOR USE WITH CHILDREN BETWEEN 6 AND 24 MONTHS.
- STOP USING WHEN A CHILD OR PET CAN CLIMB OVER OR DISLODGE THE GATE.
- USE ONLY WITH THE LOCKING/LATCHING MECHANISM SECURELY ENGAGED.
- TO PREVENT FALLS, NEVER USE ATTOP OF STAIRS.
- NEVER USE TO KEEP CHILD OR PET AWAY FROM POOL.
- ALWAYS ENSURE THE GATE IS RESTING AGAINST THE FLOOR BEFORE BEGINNING INSTALLATION.
- THIS IS A PET GATE, BUT WHEN USED WITH CHILDREN, THE SMALL PET DOOR MUST REMAIN CLOSED AND SECURELY LATCHED.
- STRANGULATION HAZARD: PETS CAN FORCE THEMSELVES INTO VERY SMALL OPENINGS; USE THIS GATE WITH PETS WHOSE HEADS WILL NOT FIT INTO OPENINGS IN THE GATE, BETWEEN THE GATE AND FLOOR, OR BETWEEN THE GATE AND WALL.
- THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL ACCIDENTS. NEVER LEAVE CHILD OR PET UNATTENDED.
- CHECK THE GATE REGULARLY TO SEE IF ALL THE HARDWARE AND MOUNTINGS ARE TIGHTENED.
- DO NOT USE IF ANY COMPONENTS ARE MISSING OR DAMAGED.
- ADULT ASSEMBLY REQUIRED.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>